Page 2
The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Notation Term Description Generic term of MB86R11 evaluation board which is a set of MB86R11EVB-CPU01 (CPU MB86R11EVB board), MB86R11EVB-BASE01 (Base board), and MB86R11EVB-OPT01 (Option board).
Page 3
When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information.
This board mounts only the external peripheral functions. The pin of MB86R11 is multifunctional, and is switched by the external pin setting or the register setting. In MB86R11EVB, to realize the switching of each resource according to the setting mode by an enable control, the buffer is inserted between MB86R11 and each resource.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 1.2. General specifications The table below shows the general specifications. Table 1-1 General specifications Item Contents Remarks CPU board Board name Base board Option board DDR2 Flash ROM ...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 1.3. External view The external view of MB86R11EVB is shown as follows. Figure 1-1 External view of MB86R11EVB External view of CPU board Figure 1-2 External view of CPU board 1. Outline of MB86R11EVB...
Page 10
MB86R11 Evaluation Board MB86R11EVB Hardware Manual External view of Base board Figure 1-3 External view of Base board External view of Option board Figure 1-4 External view of Option board 1. Outline of MB86R11EVB...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 1.4. Connection configuration The connection configuration is shown as follows. CPU Board Option Board Base Board MB86R1 Option Board Base Board CPU Board Option board side connector CPUboard side connector CN8 Base board side connector...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Outline of Hardware This chapter describes the outline of hardware of MB86R11EVB. 2.1. Hardware specifications of CPU board Table 2-1 shows the hardware specifications of CPU board. Table 2-1 Hardware specifications of CPU board...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 2.2. Hardware specifications of Base board Table 2-2 shows the hardware specifications of Base board. Table 2-2 Hardware specifications of Base board (1/2) Used FPGA Spartan6 XC6SLX100-2FGG676C (Xilinx) FBGA-676pin Item Contents Remarks The connector is DVI-I.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Details of hardware This chapter describes details of the hardware of MB86R11EVB. 3.1. CPU board Single-chip system LSI MB86R11 with built-in CoreTex-A9 is used for CPU. Table 3-1 CPU Item Model number Manufacturer Quantity...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.1.4. USB-Function The CPU board has the USB2.0-Function by 1 port (CN4). VBUS is connected to INT_A[1]. Table 3-5 USB-Function Item Model number Manufacturer Quantity Remarks USB connector UX60SC-MB-5ST miniB Schmitt buffer SN74LVC1G17DCK VBUS detection...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.1.6. Selection of boot flash memory The CPU board has the switch that selects the boot memory. It can select either of NOR-FLASH or NAND-FLASH of the external memory. Table 3-7 Slide switch Item...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.1.7. Pin Multiplex Switch The setting of each switch on CPU board is as follows. Table 3-9 DIP SW Item Model number Manufacturer Quantity Remarks DIP SW CHS-08B NIDEC COPAL ELECTRONICS SW2 (PLLMODE) Default...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.1.8. Jumper setting The CPU board has the header pin that has the following functions. Table 3-12 General-purpose pin header Item Model number Manufacturer Quantity Remarks General-purpose pin FFC-2ASM1 HONDA TSUSHIN 1 row, 2 poles...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.2. Base board The AC adaptor is connected to this board, and it supplies power to each board. The signal of the Display, Capture, and External Bus are connected to FPGA, and an enable control is performed for the buffer of each resource according to the mode that the user set.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.2.3. Display The Base board has 2 ports (Display0 and Display1) as an image output interface, and is output with the DVI connector. In addition, only the Diplay0 port has CVBS and the analog RGB connector for the analog output.
Page 26
MB86R11 Evaluation Board MB86R11EVB Hardware Manual SW1 (DISP0_DAC_CTRL) Default Set SW1[2:1]=[OFF, OFF] when I2C0 is used. Default SW1 Signal Description (I2C mode) DSEL Dual edge clock select / I2C Data This pin is an open collector input/output. If I2C bus is enabled (ISEL=OFF), then this pin is the I2C data line.
Page 27
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Default SW1 Signal Description (I2C mode) DKEN De-skewing enable. I2C mode (ISEL=OFF) DKEN pin must be set to OFF. DK[3:1] pins are ignored and the De-skewing increments are selected through the I2C interface. Non I2C mode (ISEL=ON) DKEN=ON: then default De-skewing setting is used.
Page 28
MB86R11 Evaluation Board MB86R11EVB Hardware Manual SW2 (DISP_DAC_CTRL1) Default Set SW2[2:1]=[OFF, OFF] when I2C0 is used. Default SW2 Signal Description (I2C mode) DSEL Dual edge clock select / I2C Data This pin is an open collector input/output. If I2C bus is enabled (ISEL=OFF), then this pin is the I2C data line.
Page 29
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Default SW2 Signal Description (I2C mode) DKEN De-skewing enable. I2C mode (ISEL=OFF) DKEN pin must be set to OFF. DK[3:1] pins are ignored and the De-skewing increments are selected through the I2C interface. Non I2C mode (ISEL=ON) DKEN=ON: then default De-skewing setting is used.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.2.4. Capture The Base board has 4 ports as an image output interface. Capture0 can be input from DVI, NTSC, and the pin header, and Capture1 can be input from HD, NTSC, and the pin header.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.2.5. Ethernet The Base board has 1 port (CN11) as the Ethernet interface for GbE. Table 3-22 GbE Item Model number Manufacturer Quantity Remarks GbE-PHY 88E1111-B2-BAB-C000 Marvell LAN connector TM21R-5C88(50) Transformer H5007NL Pulse Xtal...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.2.8. As for the Base board, CAN0 1ch is connected to the Dsub9 connector (CN14) as the CAN interface. Table 3-25 CAN Item Model number Manufacturer Quantity Remarks Transceiver SN65HVD234 Dsub9 connector RDED-9P-LNA(4-40)(55) Switch...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.2.9. USART (UART) As for the Base board, 2ch of USART0/1 is connected to the Dsub9 connector (CN15, CN17) and the general-purpose pin header as the UART interface. Table 3-26 UART Item Model number...
3.2.10. GPIO MB86R11 has 126 channels as the GPIO interface. The GPIO interface of 10 channels is used in the Base board. They are connected to a tact switch, LED, and a general-purpose connector. The 6 channels are used for the tact switch, and the 4 channels are used for LED and the pin header.
SDIO The Base board mounts SD0 1ch as the SDIO interface, and is connected to the SD card slot (CN21). The power supply to the SD card is controlled with the pin of MB86R11 (see Figure 3-). Table 3-30 SDIO...
Page 37
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.2.12. The Base board has the TS interface. This interface is connected to pin header (CN23). Table 3-31 TS Item Model number Manufacturer Quantity Remarks General-purpose pin OQW-11-4.2-07PW Mac8 2 rows, 14 poles header...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.2.13. MediaLB This Base board has one connector (CN24) as the MediaLB interface. Table 3-33 MediaLB Item Model number Manufacturer Quantity Remarks Connector for MOST A3A-10PA-2SV(71) 2 rows, 10 poles controller connection Table 3-34 MOST debug connector pin assignment...
MB86R11EVB Hardware Manual 3.2.14. Pin Multiplex Switch The pin of MB86R11 can be switched by MPXMODE[2:0] or the register setting. In the Base board, the same setting as the register setting is set with an external switch. Table 3-35 DIP SW...
Page 40
MB86R11 Evaluation Board MB86R11EVB Hardware Manual SW11 (SW_ED) SW11 switches the PIN mode of "PIN Group E and D" of MB86R11. Default Table 3-31 SW11 setting SW11 Group Description Default SW[1]=[OFF]: Mode5 SW[1]=[ON]: Mode0 SW[3, 2]=[ON, ON] SW[6, 5, 4]=[ON, ON, ON]: Mode0...
Page 41
MB86R11 Evaluation Board MB86R11EVB Hardware Manual SW14 (SW_IH) SW14 switches the PIN mode of "PIN Group I and H" of MB86R11. Default Table 3-39 SW14 setting SW14 Group Description Default SW[3, 2, 1]=[ON, ON, ON]: Mode0 SW[3, 2, 1]=[ON, ON, ON]...
Page 42
MB86R11 Evaluation Board MB86R11EVB Hardware Manual SW19 (DEVICE_SEL) The Caputure0-3 and the color space can be selected by the SW19[5:1] bits. In addition, FPGA internal memory can be checked by the SW19[8:6]. Default Table 3-40 SW19 setting SW19 Function Color Space...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.3. Option board All functions of MB86R11 can be used by using the CPU board, the Base board, and the Option board. The Option board has the Dual monitor function and the HDMI connector. 3.3.1. Display The Option board mounts three DVI connectors as an image output interface.
Page 44
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Default SW1 Signal Description (I2C mode) EDGE Edge select / Hot Plug input. If the I2C bus is enabled (ISEL=OFF), then this pin is used to monitor the "Hot HTPLG Plug" detect signal (Please refer to the DVI or VESA P&D and DFP standards).
Page 45
MB86R11 Evaluation Board MB86R11EVB Hardware Manual SW2 (DISP1_DAC_CTRL) Default Set SW1[2:1]=[OFF, OFF] when I2C1 is used. Default SW2 Signal Description (I2C mode) DSEL Dual edge clock select / I2C Data This pin is an open collector input/output. If I2C bus is enabled (ISEL=OFF), then this pin is the I2C data line.
Page 46
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Default SW2 Signal Description (I2C mode) DKEN De-skewing enable. I2C mode (ISEL=OFF) DKEN pin must be set to OFF. DK[3:1] pins are ignored and the De-skewing increments are selected through the I2C interface. Non I2C mode (ISEL=ON) DKEN=ON: then default De-skewing setting is used.
Page 47
MB86R11 Evaluation Board MB86R11EVB Hardware Manual SW3 (DISP2_DAC_CTRL) Default Set SW3[2:1]=[OFF, OFF] when I2C1 is used. Default SW3 Signal Description (I2C mode) DSEL Dual edge clock select / I2C Data This pin is an open collector input/output. If I2C bus is enabled (ISEL=OFF), then this pin is the I2C data line.
Page 48
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Default SW3 Signal Description (I2C mode) DKEN De-skewing enable. I2C mode (ISEL=OFF) DKEN pin must be set to OFF. DK[3:1] pins are ignored and the De-skewing increments are selected through the I2C interface. Non I2C mode (ISEL=ON) DKEN=ON: then default De-skewing setting is used.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.3.2. I2S (AUDIO) The Option board has 3 channels as an audio interface. This interface is connected to audio mini-jack and the general-purpose pin header for the connection of the microphone and the speaker.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.3.3. The Option board has 1 channel as the CAN interface. This interface is connected to Dsub9 connector (CN6). Table 3-45 CAN Item Model number Manufacturer Quantity Remarks Transceiver SN65HVD234 Dsub9 connector RDED-9P-LNA(4-40)(55) Switch...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.3.5. The Option board has 1 channel (USART ch5) as the LIN interface. This interface is connected to 2pin connector (CN28). The interface of LIN Host and Function can be switched by setting CN27.
The Option board has 2 channels of Ch1 (CN31) and Ch2 (CN32) as the SDIO interface. This interface is connected to the SD card slot. The power supply to the SD card is controlled with the pin of MB86R11 (see Figure 3-). Table 3-51 SDIO...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.3.7. The Option board has 12 channels as the PWM interface. This interface is connected to the pin header (CN29 and CN30). CN29 is connected with CR integrating circuit, and CN30 is not connected with it.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.3.9. The Option board has ATA2.5inch connector (CN33) as the IDE interface. The connection specification is Host. Table 3-56 IDE Item Model number Manufacturer Quantity Remarks ATA connector WCAW-20-2-22PW MAC8 Table 3-57 IDE connector pin assignment...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.3.10. SPI-FLASH (Quad) The Option board has the SPI-FLASH (Quad) interface. This interface is connected to the SPI-FLASH of 32Mbit and the general-purpose pin header. Table 3-58 SPI-FLASH (Quad) Item Model number Manufacturer Quantity...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 3.3.13. General-purpose ADC The Option board has general-purpose connector (CN1) as the general-purpose ADC interface. This interface is connected to the operational amplifier. The operational amplifier power supply connects +3.3V with the plus side, and connects GND with the minus side.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Board interface 4.1. CPU – Base board I/F The CPU board and the Base board are connected by two 160pin stack connectors. Table 4-1 CPU – Base board I/F Item Model number Manufacturer Quantity...
Page 60
MB86R11 Evaluation Board MB86R11EVB Hardware Manual The connector pin assignment is shown as follows. Table 4-2 Stack connector pin assignment [CPU (CN8), Base (CN31)] (1/2) Name Name +3.3V +3.3V +3.3V +3.3V DISP0G0 DISP0G4 DISP0G1 DISP0G5 DISP0G2 DISP0G6 DISP0G3 DISP0G7 DISP0R0...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 4.2. Base – Option board I/F The Base board and the Option board are connected by 160pin stack connector. Table 4-4 Base – Option board I/F Item Model number Manufacturer Quantity Remarks Connector receptacle...
Page 65
MB86R11 Evaluation Board MB86R11EVB Hardware Manual The connector pin assignment is shown as follows. Table 4-5 Stack connector pin assignment [Base (CN7), Option (CN33)] (1/2) Name Name QD0SCK QD0SDI0 QD0SDI1 QD0SEL0 QD0SDI2 QD0SEL1 QD0SDI3 QD0SEL2 QD0SEL3 A10 OSDCLK1 B10 SD1DATA0...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 4.3. Customer I/F The Base board and the Customer's board are connected by 100pin connector. Table 4-7 Connector for Customer's board connection (CN38) Item Model number Manufacturer Quantity Remarks Right angle connector 87BFN100R-3F Receptacle...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 5.2.2. VERSION register VERSION(00h) Initial 0000_0000 Name Reserved Initial 0000_0000 Name Reserved Initial xxxx_xxxx Name Version Initial xxxx_xxxx Name Revision Revison(bit7-0) FPGA Revision Version(bit15-8) FPGA Version 9. Allocation of peripheral resource and I2C port...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 5.2.3. PINMUX register PINMUX(04h) Initial 0000 Name Reserved Initial Name Initial Name Reser Initial Name Reserved The read value of PINMUX is changed by the DIPSW setting. 000 : mode0 001 : mode1 010 : mode2...
Page 75
MB86R11 Evaluation Board MB86R11EVB Hardware Manual G_B(bit5-3) Set value of SW_CB[3:1](Base Board SW10) Read attribute : ON=”L” G_C(bit8-6) SW_CB[6:4](Base BoardのSW10) set value Read attribute : ON=”L” G_D(bit11-9) SW_ED[1](Base Board SW11) set value SW_ED[1]=ON(mode0) : ”000”, OFF(mode5) : ”101” G_E(bit14-12) SW_ED[6:4](Base Board SW11) set value Read attribute : ON=”L”...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual 5.2.5. ACC_TEST register ACC_TEST(0C~FF) Initial 0000_0000 Name ACC_TEST Initial 0000_0000 Name ACC_TEST Initial 0000_0000 Name ACC_TEST Initial 0000_0000 Name ACC_TEST ACC_TEST(bit31-0) Access Test register. Setting of the SW19(DEVICE_SEL) bit[8:6]=[ON,ON,OFF]. The access except the above setting is “Hi-Z”.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Allocation of peripheral resource and I2C port MB86R11EVB has the I2C port of 5 channels. Ch0 and Ch1 of I2C are allocated in the control of the peripheral resource. The slave address must not overlap if you use the port allocated in the peripheral resource for the interface with the outside.
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Power system diagram The power system diagram is shown as follows. Figure 7-1 Power system diagram of Base board 10. Power system diagram...
Page 81
MB86R11 Evaluation Board MB86R11EVB Hardware Manual The power supply of +5V and +3.3V is supplied from the Base board to CPU board through the stack connector. Figure 7-2 Power system diagram of CPU board 10. Power system diagram...
Page 82
MB86R11 Evaluation Board MB86R11EVB Hardware Manual The power supply of +5V and +3.3V is supplied from the Base board to Option board through the stack connector. Figure 7-3 Power system diagram of Option board 10. Power system diagram...
MB86R11 Evaluation Board MB86R11EVB Hardware Manual Clock system diagram The clock system diagram of MB86R11EVB is shown as follows. Figure 8-1 Clock system diagram of MB86R11EVB 11. Clock system diagram...