Husqvarna AUTOMOWER 420 Operator's Manual page 26

3.13.4.1 To set the security level
Select 1 of 3 security levels for your product.
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 24 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Security level .
3. Use the arrow buttons and the OK button to select
the level of security.
4. Push the OK button.
3.13.4.2 To create a New loop signal
The loop signal is randomly selected to create a unique
link between the product and the charging station. In
rare cases, there may be a need to generate a new
signal, for instance if two adjacent installations have a
very similar signal.
1. Place the product in the charging station.
To get access to the menu in the
2. Do steps 1–3 in
display of the product on page 24 .
3. Use the arrow buttons and the OK button to move
through the menu structure
New loop signal .
4. Await confirmation that the loop signal has been
generated. This normally takes about 10 seconds.
3.13.4.3 To change the PIN-code
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 24 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Advanced > Change PIN-code .
3. Enter the new PIN code.
4. Push the OK button.
5. Enter the new PIN code again.
6. Push the OK button.
7. Make a note of the new PIN code. Refer to
Introduction on page 3 .
3.13.4.4 To change the duration of the alarm
1. Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Duration > Duration of alarm .
3. Use the arrow buttons to select a time interval of 1
to 20 minutes.
4. Push the BACK button.
3.13.4.5 To change the duration of the time lock
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 24 .
26 - Installation
2.
3.
4.
Settings > Security >
3.13.5 Messages
In this menu the previous fault and information
messages can be found. For some of the messages,
there are tips and advice to help to rectify the fault.
Refer to
If the product is disrupted in any way, for example it is
trapped or the battery is low, a message is saved
relating to the disruption and the time it happened.
If the same message is repeated several times, this may
indicate that an adjustment to the installation or the
product is required. Refer to
Security > Advanced >
3.13.5.1 To read the messages
1.
2.
3.
Settings > Security >
3.13.6 Weather timer
Weather timer automatically adjust the cutting time to
the growth of the grass. The product is not permitted to
operate more than the schedule settings.
Note:
to make as much operating time as possible available
for
than necessary.
Security > Advanced >
The first operation of the day is set by the schedule
settings. The product always complete 1 mowing cycle,
and then
continue to operate or not.
Note:
operate for more than 50 hours, or if a
settings is done. Weather timer is not changed if a Reset
of schedule settings is done.
Use the arrow buttons and the OK button to move
through the menu structure
Duration > Duration of time lock .
Use the number buttons to select a time interval of
1–90 days.
Push the BACK button.
Troubleshooting on page 38 .
Installation on page 15 .
To get access to the menu in the
Do steps 1–3 in
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure
messages and Messages > Info messages .
Read the messages and read the
to get information and recommendations to correct
the faults.
When using Weather timer , it is recommended
Weather timer . Do not restrict the schedule more
Weather timer selects if the product will
Weather timer is reset if the product does not
Security > Advanced >
Messages > Fault
Troubleshooting
Reset of all user
1201 - 005 - 19.03.2021