Husqvarna AUTOMOWER 310 Operator's Manual page 29

3.12.8.1 Profiles
With the function Profiles, different sets of product
settings can be saved. This can be used when one
product is used for more than one work areas and
charging stations. The product settings and the pairing
with the charging stations are saved in the profile and
can easily be used again.
To save settings to a profile
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Use profiles > Profile A, B, C.
3. Use the arrow buttons and the OK button to select
and save the profile.
4. Push the BACK button.
If settings have been changed but not saved, the symbol
* is shown beside the profile name.
To change the name of a profile
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure Settings
Use profiles > Profile A, B, C. > Rename.
3. Use the arrow buttons and the OK button to select
letters.
4. Push the BACK button to save the new profile
name.
To use a profile
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Use profiles > Profile A, B, C > Select.
3. Push the BACK button.
To connect a new charging station to a profile
1. Save the settings in a profile to be used with the
original charging station. Do steps 1–4 in
settings to a profile on page 29 .
2. Put the product in the new charging station.
3. Use the arrow buttons and the OK button to move
through the menu structure
New loop signal .
4. Save a profile for the new charging station, or
select a profile in the list. Do steps 1–4 in
settings to a profile on page 29 , or do steps 1–3 in
To use a profile on page 29 .
3.12.8.2 ECO mode
If ECO mode is activated, it switches off the signal in the
boundary loop, the guide wire and the charging station,
when the product is parked or is charging.
1440 - 004 - 24.03.2021
Note:
interference with other equipment, for example hearing
loops or garage doors.
Note:
push the STOP button before you remove the product
from the charging station. If not, the product can not be
started in the work area.
To set the ECO mode
Settings > Profiles >
1.
2.
3.
4.
3.12.8.3 Spiral Cutting
The product cuts the grass in a spiral pattern if the grass
is longer in an area.
•
> Profiles >
•
•
•
•
The level sets how sensitive the product is to changes in
grass height.
Note:
mode. Cutting in the
the product to start
start in slopes steeper than 15%.
Settings > Profiles >
To set the Spiral Cutting
1.
2.
To save
3.
Security > Advanced > To set the level of Spiral Cutting
1.
To save
2.
3.
4.
ECO mode to save energy and avoid
Use
To start the product manually in the work area,
Do steps 1–3 in To get access to the menu in the
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Settings > ECO mode .
through the menu structure
Push the OK button to select the
Push the BACK button.
Spiral cutting can be set in 5 levels:
Low-
Low
Mid
High
High+
Spiral cutting is only started in the Main area
Secondary area mode does not let
Spiral cutting . Spiral Cutting does not
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Settings > Spiral
through the menu structure
Cutting > Use Spiral Cutting .
Push the BACK button.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 23 .
Use the arrow buttons and the OK button to move
Settings > Spiral
through the menu structure
Cutting > Use Spiral Cutting > Intensity .
Use the left arrow button to select the level of the
Spiral Cutting.
Push the BACK button.
ECO mode .
Installation - 29