Sharp 8M-B120 Installation Manuallines

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

8M-B120

Installation Guidelines

<Ver. 1.0>

October 2020

System Solutions Business Unit

Business Solutions BU

SHARP Corporation

Table of Contents

Summary of Contents for Sharp 8M-B120

Page 1 8M-B120 Installation Guidelines <Ver. 1.0> October 2020 System Solutions Business Unit Business Solutions BU SHARP Corporation...
Page 2: Table Of Contents
3. Precautions for transportation 3.1 Precautions for transportation of the boxed display... 22 4. Precautions for unpacking 4.1 Precautions for unpacking... 26 4.2 Unpacking procedure... 27 4.3 Operation check when unpacking... 28 Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 4 - Installation environment of the LCD monitor differs by individual cases. Please make appropriate installation by referring to this material. If you have any difficulty in making judgment about installation or have any comments/questions about the contents of this material, please ask SHARP sales subsidiaries.
Page 5: Precautions For Use
1.Press”MENU” and select “setup” using [↑][↓][←][→] buttons and confirm with enter. 2.Press [↑][↓][←][→] to select (Information)-Identification and confirm with enter. 3.Select “Test pattern”, then the panel status will be displayed. Power connection Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 6 •For transportation and installation work, use a crane without using human power. •Check the eyebolts looseness when unpacking. Continuous operation time This product is designed for a maximum daily use of 16 hours. Use the monitor within the time of continuous operation. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 7: Maintenance Check
When the LCD panel is covered with dust, please use commercial electrostatics removal brush(dustproofing brush) Do not use a dirty cloth, a moist cloth and a chemical cloth to protect the LCD panel. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 9: Precautions For Temperature ,Clearance Space And Installation Environment
- Using a heat exchanger Measures against temperature 1 This monitor should be used at an ambient temperature between 32°F(0 ℃) Heat prevention unit and 104°F (40℃). Example of fan installation (Apiste co.) Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 10: Precautions For Direct Sunlight
> Monitor will break down or uniformity issue will occur. Cabinet will also deform. Utilizing the shade of the building Setting the monitor back to the place Example of LCD darkening Example of LCD darkening where there is no direct sunlight Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 11: Precautions For Dust
-You will need the countermeasures against thermal at the same time, such as using the heat exchanger or the air conditioner etc. Air intake fan Air exhaust fan Regular maintenance of the enclosure is required to maintain performance. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 12: Reflected Glare
If air flow fan is required, sufficient test is needed. Guard Panel Keep space At least 3cm space needed for natural air flow Light Light LCD surface temperature below 60℃ Flow Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 13: Precautions For Installation Location, Dew Condensation, Water Drops And Salt Damage
• Please install so that you can remove the influence from the wind. • Caution for salt damage • Please consult with an authorized SHARP servicing dealer with us in advance when installing near the sea where salt damage may occur. • Caution for sulfide •...
Page 14: Precautions For Vibration/Expansion/Afterimage
If it is displayed in a short time, it can recover by turning off power. However if it is displayed for a long period, you need to change the image regularly, After repair or it takes time to recover. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 15: Precautions For Power Supply
- If the cord is pulled with an excessive force, the internal core wire may be damaged and abnormal heat may occur, therefore it is recommended that the cord is fixed with a bushing or the like. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 16 -When you use light conversion cable to extend the transmission distance, EDID may not be read accurately. Not reading EDID accurately, monitors cannot display correctly. Check the image quality beforehand when using these devices. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 17 Connect the HDMI 2.0 cable to the HDMI terminal on the side terminal. Connect to the HDMI terminal for 8K. Up to 4 units can be connected INPUT 7 DP-HDMI DP-HDMI DP-HDMI HDMI DP-HDMI Any of the INPUT 1～4 Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 18: Precautions For Space Between Monitors(Multi-Display Etc.)
Please be careful not to block it as much as possible so as to pass through. Black tape monitor Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 19: Cable Wiring
2.10 Cable wiring Cable wiring To reduce loads on the terminals and prevent breakage, thread the HDMI cables through the cable clamps to secure Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 20: Lan Control
- This product is planned to support power ON/OFF control and input switching (INPUT switching) with e-Signage, as in the PN series. * It is necessary to upgrade the version of the control distribution application (e-Signage). Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 21 If you can see the following green screen, the reset is completed. If red screen appears, the reset is not completed. You need to execute “Reset” of “Error info” and “Product Reset” again 5. Unplug AC cord. Screen when the reset is completed Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 23: Precautions For Transportation Of The Boxed Display
(In case width of a cart is no more than 900mm and height of a cart is no more Margin Upper 100mm than150mm) Ceiling Carry-in space > 1,800 mm > 2,200mm * Width is calculated from the corner space 2,200mm Wall Wall Wall Wall 1,800mm 1,800mm Cart Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 24 The size of the doorway must meet the width and height. Width Depth Height Boxed display 973mm 2,940mm 1,870mm Cart > 900mm > 150mm Carry-in space > 1,000mm > 3,000mm > 2,200mm Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 25 Distance between the side wall to the edge of the door Angle Tilting angle of the product when carrying in an ※The door should have the same width of the product when the angle is 0 degree. elevator Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 27 Includes a set of stand and wall hangings Material Joint Cardboard, expanded polypropylene 1,870mm The bottom pallet is integrated with the packaging box and cannot be removed. 2,940mm 973mm Bottom pallet Forklift can be used from 4 directions Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 28: Unpacking Procedure
7. Use the eyebolts attached to the main unit and lift Wall mount bracket, bracket are included in the box it off the bottom cardboard of the package. 8. Remove the packaging PP. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 29: Operation Check When Unpacking
1.Press”MENU” and select “setup” using [↑][↓][←][→] buttons and confirm with enter. 2.Press [↑][↓][←][→] to select (Information)-Identification and confirm with enter. 3.Select “Test pattern”, then the pattern will be displayed. Power connection terminal Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 31 - It is necessary to lift the main unit for installation and maintenance. Depending on the installation location, we may ask you to install a winch or chain block on the ceiling. - The following installation and use are not possible. [Horizontal] [Vertical] [Ceiling mount] [Tilt] [Diagonal] [Rotation] Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 32 When installing or moving, hold the handle or the touch the LCD display surface. Also,do not touch designated part, or it may cause damage, malfunction the remote control light receiving section of bottom or injury. center of screen. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 33: Maintenance Space For Installation
If you cannot secure the maintenance space, you may be charged an additional cost for each maintenance. * A space is required in front of the display to install the stand. Also, a working space of about 700 mm is required on the back. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 34: Example Of Installation (Stand Installation)
Display Construction example Anchor bolt Only the screw holes are processed in the front and back. Anchor bolt Metal fittings needs to be manufactured individually. 床 floor floor Side view Front view Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 35: Example Of Installation (Wall Hanging Bracket, Bracket)
When performing maintenance, it is ・壁 Wall ・ necessary to attach the stand and ・・ Display ・ remove it from the H steel. ・・ floor Front view Side view Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 36: Example Of Installation (H Steel Installation)
・・ A winch and chain block are required above the installation position for Steel pillar installation and maintenance. Steel pillar (H steel etc.) (H steel etc.) Floor 床 Floor 正面図側面図 Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 37: How To Use Eyebolts
The space from the ceiling needs at least 4-5M. Lift with two cranes. Lift via a crossbeam. Lift with two cranes. Lift via a crossbeam. More than 45 degrees *Not to lift within 45 degrees Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 38 * It is recommended to use the cover for eyebolts regardless of stand or wall hanging installation. Remove the left and right Attach the cover with the eyebolts. attached screw *The eyebolts will be needed for repair and maintenance. Therefore please keep it in a safe space. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 39: Installation Of The Display Stand
Dimension of ground contact area width about 2,600 depth about 800 Construction example 2.08m About Only the screw holes are processed in the front and back. 1,200mm Metal fittings needs to be manufactured individually. 2.6m 0.8m Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 40: Precautions When Installing The Stand (Strength Of Anchor)
It is assumed that the above force is applied to the anchor bolt. Please select and install bolts in consideration of the safety factor. About58ｃｍ Anchor fixing position ※The calculated value is for reference only. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 41: Installation Of The Display Stand
Screw hole processed on the front and rear legs for anchor. Construction example The screw holes are processed in the front and back. Metal fittings needs to be manufactured individually. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 42: Parts List Of Wall Hanging Bracket And Mounting Bracket
PIPE B PIPE C PIPE D M33 NUT COTTER PIN LOCK PLATE-T LOCK PLATE-B SCREW M5 L=10 (mm) PIPE E STOPPER RING SCREW M6 L=10 (mm) TOP PLATE SCREW M5 L=45 (mm) M5 NUT Copyright © All rights reserved, SHARP CORPORATION...
Page 43: Mounting Of Bracket
As shown above, A and B should be fixed to be the same length. Since the packaging material avoids wall hangings. M6 screw Can be assembled with the set in the packing material. Copyright © All rights reserved, SHARP CORPORATION...
Page 44: Wall Hanging Bracket (Assembling Procedures)
2. Assemble STOPPER RING * 4pcs to PIPE C/D 1. Assemble PIPE B & PIPE C/D PIPE C/D with M5 L=10mm screw *16pcs PIPE C * 3sets PIPE D * 1set CAUTION Please assemble PIPE D at bottom side Copyright © All rights reserved, SHARP CORPORATION...
Page 45 5.7 Wall hanging bracket (Assembling procedures) 1. Assemble PIPE D & PIPE E with M5 (L=10mm)screw * 4pcs Assemble PIPE C/D & STOPPER RING*2pcs with M5( L=10mm) screw *8pcs PIPE D * 1set PIPE C * 3sets Copyright © All rights reserved, SHARP CORPORATION...
Page 46 5. Repeat 2. & 3. in previous page. 6. Fix wall hanging bracket to wall with screw. (another side) (another side) CAUTION Please fix PIPE C/D to be horizontal. Please prepare applicable screw for each wall. Copyright © All rights reserved, SHARP CORPORATION...
Page 47 Rotate pipe A (set) while lifting it slightly. Rotate until the upper notch of pipe A is inserted into pipe C. Lower the pipe A (set) and hook it on the pipe. Copyright © All rights reserved, SHARP CORPORATION Confidential...
Page 48 Please assemble LOCK PLATE-T * 2pcs at first. Next assemble LOCK PLATE-B * 2pcs LOCK PLATE-T* 2pcs Fixing plate-T Insert the fixing plate-T into Fix with M5 (L = 10mm) the above gap screws 4 places Copyright © All rights reserved, SHARP CORPORATION...
Page 49 Next assemble LOCK PLATE-B * 2pcs Fixing plate-B Fixing plate-B While supporting with hands Push in from below until LOCK PLATE-B * 2pcs Fix with M5 (L = 10mm) screws it hits pipe D. Copyright © All rights reserved, SHARP CORPORATION...
Page 51: Operation-Verified Pc / Graphics Card
The screen may turn black when the display is turned off / on. In this case, restart your PC. This symptom may occur even if you use another graphic card or DP-HDMI conversion adapter. Therefore restart the PC in the same way in that case. Copyright © All rights reserved, SHARP CORPORATION...

Sharp 8M-B120 Installation Manuallines

1 Overall Precautions

2 Design Considerations

3 Precautions for Transportation

4 Precautions for Unpacking

5 Precautions for Installation

6 Options and Recommended Equipment

Quick Links

Related Manuals for Sharp 8M-B120

Summary of Contents for Sharp 8M-B120

Table of Contents