Instructions For Installation; Electric Connection - Electrolux PR700 Installation, Operation And Maintenance Manual

II. INSTRUCTIONS FOR INSTALLATION
1. POSITIONING
Notice:
Immediately inspect for shipping damage.
• Place the appliance under its extraction hood to insure the
removal of all vapours generated whilst the appliance is working.
• Adjust the height of the appliance and level it by rotating the
adjustable feet.
• Carefully peel off the plastic covering from the external panel,
if some of the glue remains attached it can be easily removed
using a suitable solvent.
• Close the holes on the side of the appliance by means of the
plugs supplied.
• Whenever the appliance is to be placed against a wall, this last
must be made of uninflammable materials.
MINIMUM BACK CLEARANCE: 4"/100 mm
Data plate
The data plate is placed on the lower side of the control panel.
1.1 ASSEMBLY APPLIANCES (fig. 2)
• Remove the spacers from the holes "A" and "B".
• Provisionally set side by side the appliances. Level the height
of the appliances and then separate them.
• Apply a thin adhesive tape "C" on the edge of the upper top that
goes alongside.
• Apply a seam "D" of special seal on the upper zone of the top
side (DOW CORNING® 732 - Adhesive/Sealant Silicone).
• Set side by side the appliances, fastening them through the
holes "A" and "B" with screws M5x20. Fasten them by means of
nuts and washers.
• Clean the sealant in eccess with a special spatule and remove
the adhesive tape.
Warning!
The sealant begins polymerization starting from the external
surface: it is recommended not to touch the sealant in the first
three hours after application in order to avoid any trimming.
1.2 ASSEMBLY OF TOP APPLIANCE ON SUPPORT
• See the relative enclosed assembly instructions for the
installation.
2.

ELECTRIC CONNECTION

• Before carrying out the electric connection, make sure that the
voltage and frequency rated on the appliance data
conform to those of the mains supply.
• To accede to the main terminal board you just need to remove
the control panel.
• The power supply cable must be flexible and of a type matching
at least the qualities of a rubber-type cable and it must
be protected by a stiff plastic pipe.
The cable shall be connected to the main terminal board accord-
ing to the instructions of the wiring diagram attached to the
appliance and then fastened by means of cable clamps (see
points "I" fig. 1).
• For supply connections use N°14 AWG wires suitable for 60°C.
• The appliance shall be connected to the mains through a
suitable automatic circuit breaker that leaves a gap of at least
3mm between its contacts.
• The maximum leakage current is 1 mA/kW.
• The appliance must be earthed. To this purpose, inside the
appliance, near the main terminal board, there is a screw
marked with the symbol G to which must be connected the
earth wire.
The appliance must be included in a correctly dimensioned
equipotential system. The connection should be carried out
using the screw marked with the symbol E, which is located
near the front left leg.
The manufacturer accepts no liability for situations arising
from failure to comply with these safety rules.
3. COMPLIANCE REFERENCE
• The electrical connection must be carried out in conformity with
the current local safety regulations.
• This equipment is to be installed to comply with the applicable
federal, state or local codes.
These installation procedures must be followed by qualified
personnel or warranty will be void.
The National Fire Protection Association, Inc states in its NFPA
latestedition that local codes are the "authority having jurisdiction"
when it comes to installation requirements for equipment.
Therefore, installations should comply with all local codes.
4. COOKING ACCESSORIES
Container (H=100mm):
type
"
"
Container (H=150mm):
type
"
2
"
Drilled False Bottom
7
1/3 a codice 329410
2/3 a codice 329310
1/1 a codice 329210
1/3 a codice 329415
2/3 a codice 329315
1/1 a codice 329215
a codice 921622
plate