Advertisement
dO nOt cover heater when in use, and do not obstruct the air inlet and outlet grilles.
8
dO nOt place heater too close to yourself or any object, allow the air to circulate freely.
8
dO nOt touch the outlet grille of the heater during and immediately after use as it will be hot.
8
2. intrOductiOn & SpecificatiOnS
Powder coated metal cabinet with two quartz infrared elements and chemically polished reflectors for maximum heat emission. controllable power
output by rocker switches on the side of the cabinet. features easy-rolling swivel castors with 2 locking castors. suitable for wide range of heating
including restorative applications. supplied with power cable.(plug not supplied)
model no. ..............................................................irs153.V5
Power output (2 heat settings) ...................... 1500/3000 Watt
size WxdxH ................................................600x503x810mm
Weight ............................................................................13Kg
supply ........................................................... 230V-16A-50Hz
3. aSSeMblY
3.1.
fit the handle section of the support frame to the wheel section ensuring the fixing
holes align.
3.2.
fit the heater to the support frame using the bolts provided, ensuring the shaped spacers are
fitted either side of the frame as shown. tighten the bolts sufficiently to retain the heater at the
required angle.
3.3.
remove the front grille by unscrewing the retaining screws.
warning! never touch element glass directly with fingers, only touch the ceramic ends or use
‰
a soft cloth, to prevent damage.
3.4.
carefully insert each element into the two push-in side fittings with a gentle pressure.
3.5.
check the element is properly locate, then replace front grill.
4. heater OperatiOn
4.1.
Place the heater on a level floor in the area you require to heat. Allow a minimum of 2mtr between the heater and adjacent objects.
4.2.
Plug the heater into the mains supply and select the required output by using the two rocker switches on the side which switch the
elements on and off. each lamp has an output of 1500W.
4.3.
to switch the unit off, select "0" on both the rocker switches and unplug from the mains. Allow the unit to cool before handling or storage.
warninG! dO nOt touch the top of the heater when in use as it becomes hot.
‰
warninG! Always allow elements to cool before moving the units. use only on a smooth even surface. failure to do so will cause premature
‰
wear to the lamps and reduce their working life.
4.4.
the heater has a built in tilt switch safety mechanism that switches off the unit if it is tilted beyond 35° either forwards or backwards.
this prevents fire in the event of the unit being knocked over. if the unit does not turn on again when returned to the vertical, tip it
approximately 35° in the opposite direction until you hear the internal switch operate. As the heater switches on return it to the vertical
position.
5. Maintenance
warning! Before attempting any maintenance ensure the unit is unpluged from the mains power supply, it is cool and on level ground.
‰
dO nOt touch the element glass, even when cold.
8
dO nOt use the heater with out the grills fitted.
8
5.1.
To clean the reflector, remove the front grill by unscrewing the retaining screws and wipe the reflector with a clean dry cloth. dO nOt
use abrasives or solvents. The surface of the reflector is very soft and scratches may cause it to overheat. Replace the grille.
5.2.
to change the element remove the front grille by unscrewing the retaining screws.
5.2.1.
ease the sprung sockets on the ends of the element back and pull the element forward so that it clears the socket, remove element.
warning! never touch element glass directly with fingers, only touch the ceramic ends or use a soft cloth, to prevent damage.
‰
5.2.2.
carefully insert the replacement lamp into the two push in side fittings with gentle pressure.
5.2.3.
check the element is properly locate, then replace front grill.
parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on Waste electrical and electronic
equipment (Weee). When the product is no longer required, it must be disposed of in an environmentally protective way.
contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMpOrtant: no liability is accepted for incorrect use of this product.
warrantY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
P
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
01284 757500
01284 703534
irs153.V5 | issue1 20/04/16
www.sealey.co.uk
web
sales@sealey.co.uk
Advertisement
