ABB Relion REU 615 Manual
  1. Manuals
  2. Brands
  3. ABB Manuals
  4. Surge Protector
  5. REU615
  6. Manual

ABB Relion REU 615 Manual

Hide thumbs Also See for Relion REU 615:
Table of Contents

Advertisement

Quick Links

Download this manual
®
Relion
615 series
Voltage Protection and Control
REU615
DNP3 Point List Manual

Advertisement

Table of Contents
loading

Related Manuals for ABB Relion REU 615

Summary of Contents for ABB Relion REU 615

  • Page 1 ® Relion 615 series Voltage Protection and Control REU615 DNP3 Point List Manual...
  • Page 3 Document ID: 1MRS757056 Issued: 2013-02-21 Revision: C Product version: 4.0 FP1 © Copyright 2013 ABB. All rights reserved...
  • Page 4 Copyright This document and parts thereof must not be reproduced or copied without written permission from ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose. The software or hardware described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such license.
  • Page 5 In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other than under explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or damage resulting from the use of this manual or the application of the equipment.
  • Page 6 (EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB in accordance with the product standards EN 50263 and EN 60255-26 for the EMC directive, and with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive.

  • Page 7: Table Of Contents

    Table of contents Table of contents Section 1 Introduction...............7 This manual..................7 Intended audience................7 Product documentation...............7 Product documentation set............7 Document revision history.............8 Related documentation..............8 Symbols and conventions..............9 Symbols..................9 Document conventions..............9 Functions, codes and symbols............10 Section 2 DNP3 data mappings.............13 Overview...................13 Supported functions................13 Binary inputs..................15 System functions.................15 CTRL.LLN0 Local/remote state (also present in DNP IIN-...
  • Page 8 Table of contents LD0.LEDPTRC1 Global protection signals......20 LD0.TRPPTRC1 Global conditioning (1)........20 LD0.TRPPTRC2 Global conditioning (2)........21 LD0.FRPFRQ1 Frequency protection (1).......21 LD0.FRPFRQ2 Frequency protection (2).......21 LD0.FRPFRQ3 Frequency protection (3).......21 LD0.FRPFRQ4 Frequency protection (4).......22 LD0.FRPFRQ5 Frequency protection (5).......22 LD0.FRPFRQ6 Frequency protection (6).......22 LD0.LSHDPFRQ1 Load-shedding - instance 1......23 LD0.LSHDPFRQ2 Load-shedding - instance 2......23 LD0.LSHDPFRQ3 Load-shedding - instance 3......23 LD0.LSHDPFRQ4 Load-shedding - instance 4......24...
  • Page 9 Table of contents LD0.SECRSYN1 Synchrocheck ..........28 Generic functions.................29 LD0.MAPGAPC1 Multipurpose analog protection function (1)................29 LD0.MAPGAPC2 Multipurpose analog protection function (2)................29 LD0.MAPGAPC3 Multipurpose analog protection function (3)................29 LD0.MAPGAPC4 Multipurpose analog protection function (4)................29 LD0.MAPGAPC5 Multipurpose analog protection function (5)................29 LD0.MAPGAPC6 Multipurpose analog protection function (6)................30 LD0.MVGAPC1 Multipurpose binary inputs (1)......30 LD0.MVGAPC2 Multipurpose binary inputs (2)......30...
  • Page 10 Table of contents Generic functions.................36 LD0.SPCGGIO1 Multipurpose binary outputs (1)....36 LD0.SPCGGIO2 Multipurpose binary outputs (2)....37 LD0.SRGAPC1 Multipurpose binary outputs - flip-flop resets (1)................38 LD0.SRGAPC2 Multipurpose binary outputs - flip-flop resets (2)................38 Analog inputs..................38 System functions.................39 CTRL.LLN0 Local remote station off........39 LD0.LPHD1 System values............39 LD0.DNPGGIO1 Active parameter setting group....39 LD0.LEDGGIO1 LHMI LED indications (3 states)....40...
  • Page 11 Table of contents Protection functions..............45 LD0.T2PTTR1 Temperature protection values (2)....45 Protection-related functions............45 DR.RDRE1 Disturbance recorder values.......45 LD0.SECRSYN1 Synchrocheck line and bus state....45 Generic functions.................46 LD0.XRGGIO130 RTD inputs..........46 Section 3 DNP3 protocol implementation........47 DNP3 device profile................47 DNP3 implementation table..............49 Section 4 Glossary.................53 REU615 Point List Manual...

  • Page 13: Section 1 Introduction

    Section 1 1MRS757056 C Introduction Section 1 Introduction This manual The point list manual describes the outlook and properties of the data points specific to the IED. The manual should be used in conjunction with the corresponding communication protocol manual. Intended audience This manual addresses the communication system engineer or system integrator responsible for pre-engineering and engineering for communication setup in a...

  • Page 14: Document Revision History

    Content updated to correspond to the product version C/2013-02-21 4.0 FP1 Content updated to correspond to the product series version Download the latest documents from the ABB Website http://www.abb.com/substationautomation. 1.3.3 Related documentation Name of the document Document ID DNP3 Communication Protocol Manual...

  • Page 15: Symbols And Conventions

    Section 1 1MRS757056 C Introduction Symbols and conventions 1.4.1 Symbols The caution icon indicates important information or warning related to the concept discussed in the text. It might indicate the presence of a hazard which could result in corruption of software or damage to equipment or property.

  • Page 16: Functions, Codes And Symbols

    Section 1 1MRS757056 C Introduction 1.4.3 Functions, codes and symbols Table 1: REU615 functions, codes and symbols Function IEC 61850 IEC 60617 IEC-ANSI Protection Three-phase non-directional overcurrent PHLPTOC1 3I> (1) 51P-1 (1) protection, low stage Three-phase non-directional overcurrent PHHPTOC1 3I>> (1) 51P-2 (1) protection, high stage Three-phase non-directional overcurrent...
  • Page 17 Section 1 1MRS757056 C Introduction Function IEC 61850 IEC 60617 IEC-ANSI Multi-purpose protection MAPGAPC1 MAP (1) MAP (1) MAPGAPC2 MAP (2) MAP (2) MAPGAPC3 MAP (3) MAP (3) MAPGAPC4 MAP (4) MAP (4) MAPGAPC5 MAP (5) MAP (5) MAPGAPC6 MAP (6) MAP (6) Load shedding and restoration LSHDPFRQ1...

  • Page 19: Section 2 Dnp3 Data Mappings

    Section 2 1MRS757056 C DNP3 data mappings Section 2 DNP3 data mappings Overview This document describes the DNP3 data points and structures available in the IED. The data points are unmapped as a default on the DNP3 level. The point lists describe a superset of all DNP3 data available through the standard configuration/s including the optional functionalities.
  • Page 20 Section 2 1MRS757056 C DNP3 data mappings Function block UE01 UE02 PSPTUV2 ● NSPTOV1 ● NSPTOV2 ● FRPFRQ1 ● FRPFRQ2 ● FRPFRQ3 ● FRPFRQ4 ● FRPFRQ5 ● FRPFRQ6 ● T2PTTR1 ● TRPPTRC1 ● ● TRPPTRC2 ● ● ARCSARC1 ARCSARC2 ARCSARC3 MAPGAPC1 MAPGAPC2 MAPGAPC3...

  • Page 21: Binary Inputs

    Section 2 1MRS757056 C DNP3 data mappings Function block UE01 UE02 TCSSCBR2 ● ● CCRDIF1 ● SEQRFUF1 ● RDRE1 ● ● CMMXU1 ● CSMSQI1 ● VMMXU1 ● ● RESVMMXU1 ● VSMSQI1 ● ● PEMMXU1 ● XRGGIO130 FMMXU1 ● ● = available in the device variant, o = optionally available in the device variant Binary inputs Table 3: Explanations of the binary input table columns...

  • Page 22: Ld0.Lln0 Settings Supervision

    Section 2 1MRS757056 C DNP3 data mappings 2.3.1.2 LD0.LLN0 Settings supervision Table 5: LD0.LLN0 Settings supervision IEC 61850 name SA name Description Values LD0.LLN0 .SetChg.stVal Settings changed 1=Changed .SetSeld.stVal Settings reserved 1=Reserved 2.3.2 Switchgear functions 2.3.2.1 CTRL.Cxxxxx1 Circuit breaker (1) CB object and failure protection Table 6: CTRL.Cxxxxx1 Circuit breaker (1) CB object and failure protection IEC 61850 name...

  • Page 23: Ctrl.dxxxxx2 Controllable Disconnector (2)

    Section 2 1MRS757056 C DNP3 data mappings 2.3.2.3 CTRL.Dxxxxx2 Controllable disconnector (2) Table 8: CTRL.Dxxxxx2 Controllable disconnector (2) IEC 61850 name SA name Description Values CTRL.DCCILO2 .EnaCls.stVal ENA_CLOSE Close enabled 1=Enabled .EnaOpn.stVal ENA_OPEN Open enabled 1=Enabled .ItlByPss.stVal ITL_BYPASS Interlocking bypass 1=Bypassed CTRL.DCCSWI2 .Pos.stSeld...

  • Page 24: Ld0.Arcsarc2 Fault Arc Protection Stage 2

    Section 2 1MRS757056 C DNP3 data mappings 2.3.3.2 LD0.ARCSARC2 Fault arc protection stage 2 Table 11: LD0.ARCSARC2 Fault arc protection stage 2 IEC 61850 name SA name Description Values LD0.ARCSARC21 .FADet.stVal ARC_FLT_DET Arc detected 1=Detected LD0.ARCPTRC21 .Op.general OPERATE Operate 1=Operate 2.3.3.3 LD0.ARCSARC3 Fault arc protection stage 3 Table 12:...

  • Page 25: Automatic Control Functions

    Section 2 1MRS757056 C DNP3 data mappings 2.3.4 Automatic control functions 2.3.4.1 LD0.OLATCC1 On-load tap changer controller Table 15: LD0.OLATCC1 On-load tap changer controller IEC 61850 name SA name Description Values LD0.OLATCC1 .ParOp.stVal PARALLEL Parallel or single op. 1=Parallel .Auto.stVal AUTO Auto or manual op.

  • Page 26: Ld0.Vmmxu1 Three-Phase Voltage Limit Supervision

    Section 2 1MRS757056 C DNP3 data mappings 2.3.5.3 LD0.VMMXU1 Three-phase voltage limit supervision Table 18: LD0.VMMXU1 Three-phase voltage limit supervision IEC 61850 name SA name Description Values LD0.VMMXU1 .HiAlm.stVal HIGH_ALARM High alarm 1=Alarm .HiWrn.stVal HIGH_WARN High warning 1=Warning .LoAlm.stVal LOW_ALARM Low alarm 1=Alarm .LoWrn.stVal...

  • Page 27: Ld0.Trpptrc2 Global Conditioning (2)

    Section 2 1MRS757056 C DNP3 data mappings 2.3.6.3 LD0.TRPPTRC2 Global conditioning (2) Table 22: LD0.TRPPTRC2 Global conditioning (2) IEC 61850 name SA name Description Values .Op.general Operate input signal 1=Operate .Tr.general Trip output signal 1=Trip 2.3.6.4 LD0.FRPFRQ1 Frequency protection (1) Table 23: LD0.FRPFRQ1 Frequency protection (1) IEC 61850 name...

  • Page 28: Ld0.Frpfrq4 Frequency Protection (4)

    Section 2 1MRS757056 C DNP3 data mappings IEC 61850 name SA name Description Values .Op.general OPR_OFRQ -Operate 1=Operate LD0.FRPTUF3 Underfrequency .Op.general OPR_UFRQ -Operate 1=Operate LD0.FRPFRC3 Frequency gradient .Op.general OPR_FRG -Operate 1=Operate 2.3.6.7 LD0.FRPFRQ4 Frequency protection (4) Table 26: LD0.FRPFRQ4 Frequency protection (4) IEC 61850 name SA name Description...

  • Page 29: Ld0.Lshdpfrq1 Load-Shedding - Instance 1

    Section 2 1MRS757056 C DNP3 data mappings IEC 61850 name SA name Description Values .Op.general OPR_OFRQ -Operate 1=Operate LD0.FRPTUF6 Underfrequency .Op.general OPR_UFRQ -Operate 1=Operate LD0.FRPFRC6 Frequency gradient .Op.general OPR_FRG -Operate 1=Operate 2.3.6.10 LD0.LSHDPFRQ1 Load-shedding - instance 1 Table 29: LD0.LSHDPFRQ1 Load-shedding - instance 1 IEC 61850 name SA name Description...

  • Page 30: Ld0.Lshdpfrq4 Load-Shedding - Instance 4

    Section 2 1MRS757056 C DNP3 data mappings 2.3.6.13 LD0.LSHDPFRQ4 Load-shedding - instance 4 Table 32: LD0.LSHDPFRQ4 Load-shedding - instance 4 IEC 61850 name SA name Description Values LD0.LSHDPTRC4 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start .RestLodOp.general RESTORE Restore the load 1=Restore .RestLodStr.general...

  • Page 31: Ld0.Phhptoc1 Phase Overcurrent Protection - High Stage 1

    Section 2 1MRS757056 C DNP3 data mappings 2.3.6.17 LD0.PHHPTOC1 Phase overcurrent protection - high stage 1 Table 36: LD0.PHHPTOC1 Phase overcurrent protection - high stage 1 IEC 61850 name SA name Description Values LD0.PHHPTOC1 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start...

  • Page 32: Ld0.Phptov3 Phase Overvoltage Protection - Stage 3

    Section 2 1MRS757056 C DNP3 data mappings 2.3.6.22 LD0.PHPTOV3 Phase overvoltage protection - stage 3 Table 41: LD0.PHPTOV3 Phase overvoltage protection - stage 3 IEC 61850 name SA name Description Values LD0.PHPTOV3 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start 2.3.6.23 LD0.PHPTUV1 Phase undervoltage protection - stage 1...

  • Page 33: Ld0.Psptuv2 Positive-Sequence Undervoltage Protection - Stage 2

    Section 2 1MRS757056 C DNP3 data mappings 2.3.6.27 LD0.PSPTUV2 Positive-sequence undervoltage protection - stage 2 Table 46: LD0.PSPTUV2 Positive-sequence undervoltage protection - stage 2 IEC 61850 name SA name Description Values LD0.PSPTUV2 .Op.general OPERATE Stage operate 1=Operate .Str.general START Stage start 1=Start 2.3.6.28 LD0.ROVPTOV1 Residual overvoltage protection (1)

  • Page 34: Protection-Related Functions

    Section 2 1MRS757056 C DNP3 data mappings 2.3.7 Protection-related functions 2.3.7.1 LD0.CCRDIF1 Current circuit failure protection Table 51: LD0.CCRDIF1 Current circuit failure protection IEC 61850 name SA name Description Values LD0.CCRDIF1 .Alm.stVal FAIL Fail Alarm 1=Alarm .Op.general ALARM Fail Operate 1=Operate 2.3.7.2 LD0.SEQRFUF1 Fuse failure protection...

  • Page 35: Generic Functions

    Section 2 1MRS757056 C DNP3 data mappings 2.3.8 Generic functions 2.3.8.1 LD0.MAPGAPC1 Multipurpose analog protection function (1) Table 55: LD0.MAPGAPC1 Multipurpose analog protection function (1) IEC 61850 name SA name Description Values LD0.MAPGAPC1 .Op.general OPERATE Stage operate 1 = Operate .Str.general START Stage start...

  • Page 36: Ld0.Mapgapc6 Multipurpose Analog Protection Function (6)

    Section 2 1MRS757056 C DNP3 data mappings 2.3.8.6 LD0.MAPGAPC6 Multipurpose analog protection function (6) Table 60: LD0.MAPGAPC6 Multipurpose analog protection function (6) IEC 61850 name SA name Description Values LD0.MAPGAPC6 .Op.general OPERATE Stage operate 1 = Operate .Str.general START Stage start 1 = Start 2.3.8.7 LD0.MVGAPC1 Multipurpose binary inputs (1)

  • Page 37: Ld0.Spcggio2 Multipurpose Binary Outputs - Status (2)

    Section 2 1MRS757056 C DNP3 data mappings 2.3.8.9 LD0.SPCGGIO2 Multipurpose binary outputs - status (2) Table 63: LD0.SPCGGIO2 Multipurpose binary outputs - status (2) IEC 61850 name SA name Description Values LD0.SPCGGIO2 .SPCS01.stVal Output 1 state 0/1=Off/On .SPCS02.stVal Output 2 state 0/1=Off/On .SPCS03.stVal Output 3 state...

  • Page 38: Ld0.Xggio100 Physical I/O

    Section 2 1MRS757056 C DNP3 data mappings 2.3.9.3 LD0.XGGIO100 Physical I/O Table 66: LD0.XGGIO100 Physical I/O IEC 61850 name SA name Description Values LD0.XGGIO100 .SPCSO1.stVal X100-Output 1 1/0=ON/OFF .SPCSO2.stVal X100-Output 2 1/0=ON/OFF .SPCSO3.stVal X100-Output 3 1/0=ON/OFF .SPCSO4.stVal X100-Output 4 1/0=ON/OFF .SPCSO5.stVal X100-Output 5 1/0=ON/OFF...

  • Page 39: Binary Outputs

    Section 2 1MRS757056 C DNP3 data mappings IEC 61850 name SA name Description Values .Ind6.stVal X130-Input 6 1/0=ON/OFF .SPCSO1.stVal X130-Output 1 1/0=ON/OFF .SPCSO2.stVal X130-Output 2 1/0=ON/OFF .SPCSO3.stVal X130-Output 3 1/0=ON/OFF Binary outputs Table 69: Explanations of the binary output table columns Column name Description IEC 61850...

  • Page 40: Switchgear Functions

    Section 2 1MRS757056 C DNP3 data mappings IEC 61850 name SA name Description Type .ActSG4.ctlVal Setting group 4 .ActSG5.ctlVal Setting group 5 .ActSG6.ctlVal Setting group 6 2.4.2 Switchgear functions 2.4.2.1 CTRL.CBCSWI1 Circuit breaker control Table 72: CTRL.CBCSWI1 Circuit breaker control IEC 61850 name SA name Description...

  • Page 41: Metering And Measurand Functions

    Section 2 1MRS757056 C DNP3 data mappings 2.4.3 Metering and measurand functions 2.4.3.1 LD0.PEMMXU1 Reset accumulated energy values Table 76: LD0.PEMMXU1 Reset accumulated energy values IEC 61850 name SA name Description Type LD0.PEMMXU1 .SupDmdRs.Oper.ctlVal RSTACM Reset accum. energy 2.4.4 Protection functions 2.4.4.1 LD0.LSHDPFRQ1 Loadshedding controls (1) Table 77:...

  • Page 42: Ld0.Lshdpfrq4 Load Shedding Controls (4)

    Section 2 1MRS757056 C DNP3 data mappings 2.4.4.4 LD0.LSHDPFRQ4 Load shedding controls (4) Table 80: LD0.LSHDPFRQ4 Load shedding controls (4) IEC 61850 name SA name Description Type LD0.LSHDPTRC4 .ManRest.Oper.ctlVal MAN_RESTORE Manual restore .BlkRest.Oper.ctlVal BLK_REST Cancel restore 2.4.4.5 LD0.LSHDPFRQ5 Load shedding controls (5) Table 81: LD0.LSHDPFRQ5 Load shedding controls (5) IEC 61850 name...

  • Page 43: Ld0.Spcggio2 Multipurpose Binary Outputs (2)

    Section 2 1MRS757056 C DNP3 data mappings IEC 61850 name SA name Description Type .SPCS04.ctlVal Output 4 control On/Off .SPCS05.ctlVal Output 5 control On/Off .SPCS06.ctlVal Output 6 control On/Off .SPCS07.ctlVal Output 7 control On/Off .SPCS08.ctlVal Output 8 control On/Off .SPCS09.ctlVal Output 9 control On/Off .SPCS10.ctlVal...

  • Page 44: Ld0.Srgapc1 Multipurpose Binary Outputs - Flip-Flop Resets (1)

    Section 2 1MRS757056 C DNP3 data mappings 2.4.6.3 LD0.SRGAPC1 Multipurpose binary outputs - flip-flop resets (1) Table 85: LD0.SRGAPC1 Multipurpose binary outputs - flip-flop resets (1) IEC 61850 name SA name Description Type LD0.SRGAPC1 .Rs1.ctlVal Reset flip-flop 1 .Rs2.ctlVal Reset flip-flop 2 .Rs3.ctlVal Reset flip-flop 3 .Rs4.ctlVal...

  • Page 45: System Functions

    Section 2 1MRS757056 C DNP3 data mappings Column name Description Values The value range of the original IEC 61850 data. Scaling is needed to convert floating point data into DNP3 integer values. Scaling type selected as default. Default “R” means ratio scaling. See the DNP communication protocol manual for details.

  • Page 46: Ld0.Ledggio1 Lhmi Led Indications (3 States)

    Section 2 1MRS757056 C DNP3 data mappings 2.5.1.4 LD0.LEDGGIO1 LHMI LED indications (3 states) Table 91: LD0.LEDGGIO1 LHMI LED indications (3 states) IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.LEDGGIO1 0/1/3=Off/Ok/ .ISCSO1.stVal LED 1 state Alarm 0,3,0,3 0/1/3=Off/Ok/ .ISCSO2.stVal LED 2 state Alarm...

  • Page 47: Ctrl.dcsxswi2 Disconnector 2, 4-Pole (2 Bit) Position Values

    Section 2 1MRS757056 C DNP3 data mappings 2.5.2.3 CTRL.DCSXSWI2 Disconnector 2, 4-pole (2 bit) position values Table 94: CTRL.DCSXSWI2 Disconnector 2, 4-pole (2 bit) position values IEC 61850 name SA name Description Values Arg 1,2,3,4 CTRL.DCSXSWI2 Intermediate=0; Off=1; On=2; .Pos.stVal POSITION Bad=3 0…3...

  • Page 48: Ctrl.essxswi2 Earth Switch 2, 4-Pole (2 Bit) Position Values

    Section 2 1MRS757056 C DNP3 data mappings 2.5.2.8 CTRL.ESSXSWI2 Earth switch 2, 4-pole (2 bit) position values Table 99: CTRL.ESSXSWI2 Earth switch 2, 4-pole (2 bit) position values IEC 61850 name SA name Description Values Arg 1,2,3,4 CTRL.ESSXSWI2 Intermediate=0; Off=1; On=2; .Pos.stVal POSITION Bad=3...

  • Page 49: Metering And Measurand Functions

    Section 2 1MRS757056 C DNP3 data mappings 2.5.5 Metering and measurand functions 2.5.5.1 LD0.CMMXU1 Phase currents (1) Table 103: LD0.CMMXU1 Phase currents (1) IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.CMMXU1 Phase-to-ground current .A.phsA.instCVal.mag I_INST_A -phsA magnitude 0.00..40.0 [xIn] 0,40,0,4000 .A.phsB.instCVal.mag I_INST_B...

  • Page 50: Ld0.Resvmmxu1 Residual Voltage (1)

    Section 2 1MRS757056 C DNP3 data mappings IEC 61850 name SA name Description Values Arg 1,2,3,4 0.00…4.00 .phsAB.cVal.mag U_DB_AB -phsAB magnitude [xUn] 0,4,0,400 0.00…4.00 .phsBC.cVal.mag U_DB_BC -phsBC magnitude [xUn] 0,4,0,400 0.00…4.00 .phsCA.cVal.mag U_DB_CA -phsCA magnitude [xUn] 0,4,0,400 2.5.5.5 LD0.RESVMMXU1 Residual voltage (1) Table 107: LD0.RESVMMXU1 Residual voltage (1) IEC 61850 name...

  • Page 51: Ld0.Fmmxu1 Frequency Measurement

    Section 2 1MRS757056 C DNP3 data mappings 2.5.5.8 LD0.FMMXU1 Frequency measurement Table 110: LD0.FMMXU1 Frequency measurement IEC 61850 name SA name Description Values Arg 1,2,3,4 LD0.FMMXU1 .Hz.mag Frequency value 35…75 [Hz] 35,75,3500,7500 2.5.6 Protection functions 2.5.6.1 LD0.T2PTTR1 Temperature protection values (2) Table 111: LD0.T2PTTR1 Temperature protection values (2) IEC 61850 name...

  • Page 52: Generic Functions

    Section 2 1MRS757056 C DNP3 data mappings 2.5.8 Generic functions 2.5.8.1 LD0.XRGGIO130 RTD inputs Table 114: LD0.XRGGIO130 RTD inputs IEC 61850 name SA name Description Values Arg 1,2,3,4 -10000… .AnIn1.instMag AI_VAL1 RTD input 1 10000 -1E4,1E4,-1E4,1E4 -10000… .AnIn2.instMag AI_VAL2 RTD input 2 10000 -1E4,1E4,-1E4,1E4 -10000…...

  • Page 53: Section 3 Dnp3 Protocol Implementation

    Implementation table and the point list tables, provides a complete configuration/interoperability guide for communicating with a device. Table 115: Device profile document DNP3 device profile document Vendor name: ABB Oy Device name: REU615 Highest DNP level supported: Device function: For requests: Level 2+ ○...
  • Page 54 Section 3 1MRS757056 C DNP3 protocol implementation DNP3 device profile document ○ Sometimes ● Configurable as: "Only when reporting event data", or "When reporting event data or multi-fragment messages" Timeouts while waiting for: Data link ○ None ○ Fixed at ____ ○...

  • Page 55: Dnp3 Implementation Table

    Section 3 1MRS757056 C DNP3 protocol implementation DNP3 device profile document ○ Configurable ○ When device restarts ○ Only certain objects ○ When status flags change ○ Sometimes (attach explanation) ○ ENABLE/DISABLE UNSOLICITED No other options are permitted. function codes supported Default counter object/variation: Counters roll over at: ●...
  • Page 56 Section 3 1MRS757056 C DNP3 protocol implementation Table 116: Implementation table OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) Object Variation Function codes Qualifier codes number number Description Function codes (dec) Qualifier codes (hex) (dec) (hex) Binary 1 (read) 00, 01 (start-stop) input –...
  • Page 57 Section 3 1MRS757056 C DNP3 protocol implementation OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) 16-bit 1 (read) 00, 01 (start-stop) 129 (response) 00, 01 (start-stop) 2 (default) analog 06 (no range, or all) 17, 28 (index) input 07, 08 (limited qty) 17, 28 (index) 32-bit...
  • Page 58 Section 3 1MRS757056 C DNP3 protocol implementation OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) Time delay 129 (response) 07 (limited qty) fine (qty = 1) Not defined Class 0 1 (read) 06 (no range, or all) data Class 1 1 (read) 06 (no range, or all)

  • Page 59: Section 4 Glossary

    Section 4 1MRS757056 C Glossary Section 4 Glossary Application function block library CROB Control relay output block Common time of occurrence. The time and date CTO object is an information object that represents the absolute time of day. DNP3 A distributed network protocol originally developed by Westronic.
  • Page 64 Contact us ABB Oy Medium Voltage Products, Distribution Automation P.O. Box 699 FI-65101 VAASA, Finland Phone +358 10 22 11 +358 10 22 41094 ABB Limited Distribution Automation Maneja Vadodara 390013, India Phone +91 265 2604032 +91 265 2638922 www.abb.com/substationautomation...

Table of Contents