Related Manuals for Huawei AP6510DN-AGN-US
Summary of Contents for Huawei AP6510DN-AGN-US
- Page 1 AP6510DN-AGN-US Outdoor Wireless LAN Access Point Quick Start Guide HUAWEI TECHNOLOGIES CO., LTD.
- Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope.
-
Page 3: Symbol Conventions
Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a potentially hazardous situation, which if not avoided, could CAUTION result in equipment damage, data loss, performance degradation, or unexpected results. Provides additional information to emphasize or supplement important NOTE points of the main text. -
Page 4: Packing List
AP6510DN-AGN-US Quick Start Guide 技术支持 Before performing Installation, confirm that the installation accessories and tools are available. Technical Support Installation tools: Installation accessories: Huawei Technologies Co., Ltd. Address: Huawei Industrial Base Flat-head Phillips Diagonal Adjustable 6mm drill Bantian,Longgang Hammer screwdriver... - Page 5 ● Select an appropriate installation position and leave space above and around the device for cooling air circulation. ● Outdoors Aps are used for hotspot coverage and often installed against walls or poles. The pole diameter is 48 mm to 114 mm. AP6510DN-AGN-US dimensions (unit: mm) without a backplane Recommended AP6510DN-AGN-US installation space support.
- Page 6 And use the screwdriver to secure screws on the hoop. Field strength 场强示意 ● The procedure for installing the AP6510DN-AGN-US against a horizontal pole is similar to the procedure for installing the AP6510DN-AGN-US against a vertical pole. 上电调试 ● Installing the Security Lock...
-
Page 7: Installing Cables
Installing Cables ● AP6510DN-AGN-US external cable arrangement drawing Feed line Feed line Feed line Feed line Ground cable Network cable ● Connecting network cables 1. Use a shield straight-through cable. Cut the cable of proper length based on the distance between the AP and the PSE device, peel the insulation on both ends of the network cable, and crimp the wires to RJ45 connectors. - Page 8 Installing Cables ● Connecting the feed line 1. The outdoor AP's antenna ports already have 5 KA surge protection capability. Generally, no surge protection devices need to be installed; therefore, the antenna cables are directly connected to the AP's antenna ports. Feed line Waterproof adhesive tape 2.
- Page 9 Installing Cables CAUTION Requirements for laying out ground cables: 1. All ground cables must be connected to a ground bar. 2. The ground cable cannot be led in aerially, but buried in the earth or arranged indoor. 3. Both ends of the external conductor of the coaxial cable and those of the insulation of the shielded cable should have good electric contact with the metal shell of the equipment they connect to.
-
Page 10: Technical Specifications
Power-on NOTE 2 连接线缆 The AP6510DN-AGN-US supports the PoE function that complies with 802.3at. Power on the AP6510DN-AGN-US and check the indicator status to determine the system running status. Information Description Link Wireless Type Steady green The device is being started. -
Page 11: Logging In To The Router
Logging In to the Router After an AP is powered on, you can log in to the AP using the following methods. 1. Logging In to the AP Using Telnet This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using commands. -
Page 12: Declaration On Hazardous Substances In Electronic Information Products
Declaration on Hazardous Substances in Electronic Information Products Hazardous Substances Part Cr6+ PBDE Mechanical part Board/circuit module Signal cable Cable connector Power adapter Auxiliary equipment O: Indicates that the concentration of the hazardous substance contained in all the homogeneous materials of this part is below the limit requirement of the SJ/T 11363-2006 standard. -
Page 13: Warranty Card
In any of the following cases, the warranty card becomes unenforceable or inapplicable without prior notice: 1. The defects are caused by improper handling in transportation and assembly. 2. The defects are caused by the fact that the product is dismantled or altered by anyone that is not from a Huawei authorized service partner. - Page 14 HUAWEI TECHNOLOGIES CO., LTD . Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China http://enterprise.huawei.com...