Related Manuals for Huawei AP6610DN-AGN-US
Summary of Contents for Huawei AP6610DN-AGN-US
-
Page 1: Quick Start Guide
AP6610DN-AGN-US Outdoor Wireless LAN Access Point Quick Start Guide HUAWEI TECHNOLOGIES CO., LTD. - Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope.
-
Page 3: Symbol Conventions
Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a potentially hazardous situation, which if not avoided, could CAUTION result in equipment damage, data loss, performance degradation, or unexpected results. Provides additional information to emphasize or supplement important NOTE points of the main text. -
Page 4: Packing List
AP6610DN-AGN-US Quick Start Guide 技术支持 Before performing Installation, confirm that the installation accessories and tools are available. Technical Support Installation tools: Installation accessories: Huawei Technologies Co., Ltd. Address: Huawei Industrial Base Flat-head Phillips Diagonal Adjustable 6mm drill Hammer screwdriver screwdriver... - Page 5 ● Select an appropriate installation position and leave space above and around the device for cooling air circulation. ● Outdoors Aps are used for hotspot coverage and often installed against walls or poles. The pole diameter is 48 mm to 114 mm. AP6610DN-AGN-US dimensions (unit: mm) without a backplane Recommended AP6610DN-AGN-US installation space support.
- Page 6 Field strength 场强示意 ● The procedure for installing the AP6610DN-AGN-US against a horizontal pole is similar to the procedure for installing the AP6610DN-AGN-US against a vertical pole. 上电调试 ● Installing the Security Lock...
-
Page 7: Installing Cables
Installing Cables ● AP6610DN-AGN-US external cable arrangement drawing Feed line Feed line Feed line Feed line Ground cable AC power cable Optical fiber ● Connecting the feed line 1. The outdoor AP's antenna ports already have 5 KA surge protection capability. Generally, no surge protection devices need to be installed;... - Page 8 1. The right figure shows the appearance of the optical fiber： 2. The optical fiber connection of AP6610DN-AGN-US is similar to that of WA653SN. Here, WA653SN is used as an example. Connect the optical fiber to the AP and ensure that the waterproof connector is fastened.
- Page 9 Installing Cables 4. Tighten the screws in the three holes using a Phillips 3. Install the core wires in the correct holes. screwdriver. CAUTION After the screws are tightened, check that the cable is securely installed by evenly pulling the cable with a 10 kg force.
- Page 10 Installing Cables ● Connecting the ground cable Cut the cable of proper length, and select 6-M4 OT terminal for the AP and 6-M6 OT terminal for the ground bar. Connecting the ground CAUTION Requirements for laying out ground cables: 1. All ground cables must be connected to a ground bar. 2.
-
Page 11: Technical Specifications
Power-on NOTE 2 连接线缆 Power on the AP6610DN-AGN-US and check the indicator status to determine the system running status. Information Description Link Wireless Type Steady green The device is being started. The system is working properly. Blinking green Startup status Steady red The system fails to load the DRAM or system software. -
Page 12: Logging In To The Router
Logging In to the Router After an AP is powered on, you can log in to the AP using the following methods. 1. Logging In to the AP Using Telnet This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using commands. -
Page 13: Declaration On Hazardous Substances In Electronic Information Products
Declaration on Hazardous Substances in Electronic Information Products Hazardous Substances Part Cr6+ PBDE Mechanical part Board/circuit module Signal cable Cable connector Power adapter Auxiliary equipment O: Indicates that the concentration of the hazardous substance contained in all the homogeneous materials of this part is below the limit requirement of the SJ/T 11363-2006 standard. -
Page 14: Warranty Card
In any of the following cases, the warranty card becomes unenforceable or inapplicable without prior notice: 1. The defects are caused by improper handling in transportation and assembly. 2. The defects are caused by the fact that the product is dismantled or altered by anyone that is not from a Huawei authorized service partner. - Page 15 HUAWEI TECHNOLOGIES CO., LTD . Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Http://enterprise.huawei.com...