Advertisement
3. SPECIFICATION
MODEL NO: ............................................................... SD008
Electrical Plug Type: ................................................ 3-Pin BS
Frequency: .....................................................................50Hz
Heating Element Voltage: ......................................... 230V AC
Power: .............................................................................48W
4. OPERATION
4.1.
Unpack the soldering station and check all parts. Damaged parts must not be put into operation.
4.2.
Put the holding rack for the soldering iron sideways in the soldering station, wet the cleaning sponge in the sponge rack with water.
4.3.
Put the soldering iron in the holding rack.
4.4.
Place the soldering station on a solid and dry surface.
4.5.
Connect the mains supply and turn on the soldering station by using the power switch (I=ON/0=OFF).When turned on, the
power switch is lit.
4.6.
Always put the soldering iron on the holding rack when it is heating up or during breaks from soldering.
4.7.
Make sure the workbench for soldering is clean.
4.8.
Only use solder for electronics. Acidic solder can damage the soldering tip or the work piece.
4.9.
Regulate the desired temperature of the soldering iron with the adjusting knob.
4.10.
The colour-coded areas are equal to following temperatures:
Yellow ≥ 160°C
Light Orange 180°C to 350°C
Deep Orange 350°C to 450°C
Red ≥ 550°C
4.11.
Lower the temperature during breaks, this saves energy and extends the durability of the soldering tip.
4.12.
Wait for about 10 minutes until the soldering tip reaches the setting temperature, test the temperature by touching the soldering tip
with solder. If the solder melts away easily, start soldering.
4.13.
Tin the hot soldering tip with solder; wipe off excessive solder on the wet cleaning sponge.
4.14.
Heat up the to-be-soldered part with the soldering tip and add solder.
4.15.
Wait for the hot solder to cool down.
4.16.
Clean the soldering tip on the wet sponge after each soldering.
4.17.
After the soldering is done, put back the soldering iron in the rack and turn off the soldering Station at the main switch.
4.18.
DO NOT file off the soldering tip, or it will be damaged.
4.19.
Never touch the hot soldering tip.
4.20.
Let the soldering iron cool down after use.
4.21.
The soldering iron should not be dunked into water.
4.22.
During breaks, the soldering iron must be placed in the holding rack.
5. MAINTENANCE
5.1.
This tool must be placed on its stand when not in use.
5.2.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to
avoid hazards.
5.3.
GENERAL CLEANING
5.3.1.
The outer case of the iron or station may be cleaned with a damp cloth using small amounts of liquid detergent Never submerse the
unit in liquid or allow any liquid to enter the housing. Never use solvent to clean the case.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
01284 703534
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
SD008 Issue 1 28/01/2021
Advertisement
