Pioneer AVH-Z5290BT Operation Manual

Pioneer AVH-Z5290BT Operation Manual

Monitor rds av receiver

Advertisement

Quick Links

AVH-Z5290BT
MONITOR RDS AV RECEIVER
Operation Manual

Advertisement

Table of Contents
loading

Summary of Contents for Pioneer AVH-Z5290BT

  • Page 1 AVH-Z5290BT MONITOR RDS AV RECEIVER Operation Manual...
  • Page 2: Table Of Contents

    Contents Thank you for buying this Pioneer product. Please read through these instructions so you will know how to operate your model properly. After you have finished reading the instructions, keep this document in a safe place for future reference.
  • Page 3 ■ Other functions................. 82 ■ Appendix ................... 84 - 3 -...
  • Page 4: Precaution

    • If you notice smoke, a strange noise or odour from this product, or any other abnormal signs on the LCD screen, turn off the power immediately and consult your dealer or the nearest authorised Pioneer Service Station. Using this product in this condition may result in permanent damage to the system.
  • Page 5 • Never set the volume of this product so high that you cannot hear outside traffic and emergency vehicles. • To promote safety, certain functions are disabled unless the vehicle is stopped and the handbrake is applied. • Keep this manual handy as a reference for operating procedures and safety information.
  • Page 6 • To prevent data loss and damage to the storage device, never remove it from this product while data is being transferred. • Pioneer cannot guarantee compatibility with all USB mass storage devices and assumes no responsibility for any loss of data on media players, iPhone, smartphone, or other devices while using this product.
  • Page 7 • We offer the latest information about PIONEER CORPORATION on our website. • Pioneer regularly provides software updates to further improve it’s products. Please check the support section of the Pioneer website for all available software updates. Protecting the LCD panel and screen •...
  • Page 8: Parts And Controls

    Parts and controls Main unit Press to activate the voice recognition mode such as Siri when the iPhone is connected to the unit via Bluetooth or USB. VOL (+/ Press to display the top menu screen. Press and hold to power off. To power back on, press any button. Press to switch between the Application screen and the AV operation screen.
  • Page 9 Remote control Volume (+/-) MODE Press to switch between the Application screen and the AV operation screen. Press and hold to turn off the display. Press to cycle through all the available sources. Press and hold to turn the source off. TOP MENU Press to return to the top menu during DVD playback.
  • Page 10: Basic Operation

    Basic operation Resetting the microprocessor CAUTION • Pressing the RESET button resets settings and recorded contents to the factory settings. – Do not perform this operation when a device is connected to this product. – Some of the settings and recorded contents will not be reset. •...
  • Page 11 If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. • Batteries (battery pack or batteries installed) must not be exposed to excessive heat such as sunshine, fire or the like.
  • Page 12 Touch [OK]. Initial Legal Disclaimer screen appears. Touch [OK]. The top menu screen appears. NOTE Once the speaker mode is set, the setting cannot be changed unless this product is restored to the default settings. Restore the default settings to change the speaker mode setting (page 83). Switching the speaker mode To change the speaker mode, you need to restore this product to the default settings.
  • Page 13 Touching an item on the list allows you to narrow down the options and proceed to the next operation. Appears when all characters are not displayed on the display area. If you touch the key, the rests are scrolled for display. NOTE This function is available only when you stop your vehicle in a safe place and apply the handbrake.
  • Page 14 Skips files forwards or backwards. Performs fast reverse or fast forwards. Displays setting menu screen (page 61). Closes the menu bar. Top menu screen Switches the top menu screen layout. Touch and hold appears at the top of the screen. Touch When you finish switching the layout, press Favourite source icons...
  • Page 15 AV operation area Displays the current source. Touch to go to the displayed source. TIPS • When the control icons are displayed at the bottom of the key, you can control the displayed operation. • You can also switch to display/hide the artwork with the following procedure. Touch and hold appears on the AV operation area.
  • Page 16: Bluetooth

    Bluetooth Bluetooth connection Turn on the Bluetooth function on the device. Press Touch then The Bluetooth screen appears. Touch [Connection]. Touch The unit starts to search for available devices, then displays them in the device list. Touch the Bluetooth device name. After the device is successfully registered, a Bluetooth connection is established by the system.
  • Page 17 CAUTION Never turn this product off and disconnect the device while the Bluetooth setting operation is being processed. Menu Item Description [Connection] Connect, disconnect, or delete registered Bluetooth device manually. Touch to delete registered device. To connect a registered Bluetooth device manually, touch the name of the device.
  • Page 18 registered devices are already connected, you can connect the remaining third device to use the audio function only from the switch devices key on the audio source screen. • The icon for the mobile phone currently being used is displayed on the Phone menu screen.
  • Page 19 The following items are displayed. • Name of the current mobile phone • List number of the current mobile phone • Reception status of the current mobile phone • Battery status of the current mobile phone If you connect two mobile phones to this product at the same time, you can switch between the mobile phones using the switch devices key.
  • Page 20 Touch Touch On the [Phone Book] screen, touch the desired name to display the contact’s phone number. Touch ▶Dialling from the preset dial list Touch Touch the desired entry on the list to make a call. The dial screen appears and dialling starts. ▶Deleting a phone number Press Touch...
  • Page 21 Press Touch Touch The voice recognition function launches and the voice control screen appears. TIPS • You can also launch the voice recognition function by pressing button. • If two mobile phones are automatically connected to this product with the Bluetooth device auto connect function, the voice recognition function (Siri Eyes Free Mode) will be set on the second phone.
  • Page 22 Touch to turn private mode on or off. NOTES • If two mobile phones are connected to this product and the first phone is set to private mode, you can receive incoming calls on the second phone while maintaining the call in progress on the first phone.
  • Page 23 ▶The received call and dialled number histories • You cannot make a call to the entry of an unknown user (no phone number) in the received call history. • If calls are made by operating your mobile phone, no history data will be recorded in this product.
  • Page 24 The Bluetooth audio playback screen appears. Basic operation Bluetooth audio playback screen Track number indicator Switches between playback and pause. Skips files forwards or backwards. • By pressing then touch , you can also skip files forwards or backwards. • By pressing then touch and hold , you can also perform fast reverse or fast forwards.
  • Page 25: Av Source

    AV source Supported AV source You can play or use the following sources with this product. • Radio • CD • Disc (compressed audio or video files on discs) • DVD-Video • USB The following sources can be played back or used by connecting an auxiliary device. •...
  • Page 26 Selecting a source Source on the AV source selection screen Press then touch Touch the source icon. When you select [Source OFF], the AV source is turned off. Source on the source list Press then touch the AV operation key. Touch Touch the source key.
  • Page 27 Adjusting the range of favourite source icons area NOTE This function is available only when you stop your vehicle in a safe place and apply the handbrake. Press Touch and hold appears at the top left of the favourite source icons. Drag to the desired position.
  • Page 28: Radio

    Radio Starting procedure Press then touch Touch [Radio]. The Radio screen appears. Basic operation Radio screen Recalls the preset channel stored to a key from memory. Stores the current broadcast frequency to a key. Displays the preset channel list. Select an item on the list ([1] to [6]) to switch to the preset channel. Selects the FM1, FM2, FM3, or AM band.
  • Page 29 Manual tuning Seek tuning or non stop seek tuning Releasing the key in a few seconds skips to the nearest station from the current frequency. Keep holding the key for long seconds to perform non stop seek tuning. Searches for a broadcast by PTY information (page 29). TIPS •...
  • Page 30 To cancel the storage process Touch [Cancel]. Radio settings Press Touch then The system setting screen appears. Touch [AV Source Settings]. Touch [Radio settings]. The menu items vary according to the source. Menu Item Description [Local] Local seek tuning allows you to only tune into [Off] radio stations with sufficiently strong signals.
  • Page 31 Menu Item Description [Alarm Interrupt ]*2 The alarm broadcast can be received from the [On] [Off] last selected frequency, interrupting the other sources. [TA Interrupt]*2 Receives the traffic announcement from the last [On] [Off] selected frequency, interrupting the other sources. [News Interrupt]*2 Interrupt the currently selected source with [On] [Off]...
  • Page 32: Disc

    Disc Inserting and ejecting a disc You can play a normal music CD, Video-CD, or DVD-Video using the built-in drive of this product. CAUTION Do not insert anything other than a disc into the disc-loading slot. Inserting a disc Insert a disc into the disc-loading slot. The source changes and then playback will start.
  • Page 33 Audio source Audio source screen Track number indicator Switches between playback and pause. Skips files forwards or backwards. Sets a repeat play for the current disc/the current track. Plays or does not play tracks in random order. Selects a track from the list. Touch a track on the list to play back.
  • Page 34 Video source screen 1 Hides the touch panel keys. To display the keys again, touch anywhere on the screen. Performs fast reverse or fast forwards. Touch again to change the playback speed. Stops playback. Performs frame-by-frame playback. Performs slow-motion playback. Each time you touch , it changes the speed in four steps in the following order: 1/16 ->...
  • Page 35 Searches for the part you want to play. Touch [Title], [Chapter], [10Key], or [Track] then input the desired number from [0] to [9]. To start playback from the number you registered, touch TIPS • To cancel an input number, touch [C]. •...
  • Page 36 Resumes playback (Bookmark). This function is available for DVD-Video. You can memorise one point as a Bookmark for a disc (up to five discs). To clear the bookmark on the disc, touch and hold this key. Returns and begins playback from the specified point. This function is available for DVD-Video and Video-CDs featuring PBC (playback control).
  • Page 37: Compressed Files

    Compressed files Inserting and ejecting media You can play compressed audio, compressed video, or still image files stored in a disc or an external storage device. CAUTION Do not insert anything other than a disc into the disc-loading slot. Inserting a disc Insert a disc into the disc-loading slot.
  • Page 38 USB cable USB storage device Unplugging a USB storage device Pull out the USB storage device from the USB cable. NOTES • Check that no data is being accessed before pulling out the USB storage device. • Turn off (ACC OFF) the ignition switch before unplugging the USB storage device. Starting procedure For Disc Insert the disc (page 37).
  • Page 39 Audio source Audio source screen 1 (Example: USB) Displays the link search screen. Touch the song to play back followed by touching the song information, after switching to Music Browse mode (page 40). If you touch the artwork, the list of songs in the album is displayed. NOTE This function is available for the USB storage device only.
  • Page 40 Switches the following media file types. [Music]: Compressed audio files [Video]: Compressed video files [CD-DA]: Audio data (CD-DA) [Photo]: Image files Selects a file from the list. Touch a file on the list to playback. Touching a folder on the list shows its contents. You can play a file on the list by touching it.
  • Page 41 NOTES • This function is available for the USB storage device only. • Music Browse mode cannot be held once the power is turned off. Touch to create a database. Music Browse mode will be available after the database has been created. Touch Touch the desired category to display the file list.
  • Page 42 Performs fast reverse or fast forwards. Touch again to change the playback speed. Stops playback. Performs frame-by-frame playback. Performs slow-motion playback. Sets a repeat play range for all files/the current folder/the current file. Switches the audio/subtitle language. NOTE Switching of the subtitle function is only available on disc. Switches the following media file types.
  • Page 43 Still image screen Hides the touch panel keys. To display the keys again, touch anywhere on the screen. Switches between playback and pause. Skips files forwards or backwards. Selects the previous folder or the next folder. Saves the current images as the wallpaper. Touch the following items then touch [Yes] to overwrite the image.
  • Page 44 Selects a file from the list. Touch a file on the list to playback. Touching a folder on the list shows its contents. You can play a file on the list by touching it. - 44 -...
  • Page 45: Ipod

    iPod Connecting your iPod When connecting an iPod to this product, the settings are automatically configured according to the device to be connected. For details of the compatiblity, refer to Compatible iPod/iPhone models (page 97). NOTES • Depending on the generation or version of the iPod, some functions may not be available. •...
  • Page 46 Displays the link search screen. Select a song from the list related to the song currently playing. If you touch the artwork, the list of songs in the album is displayed. NOTE This function is not available while playing Apple Music Radio. Switches between playback and pause.
  • Page 47 Audio source screen 2 Changes the audiobook speed. Normal—Fast—Slow Displays the hidden function bar. Apple Music® Radio source Important Apple Music Radio may not be available in your country or region. For details about Apple Music Radio, visit the following site: http://www.apple.com/music/ NOTE This function is only available when using the iPod function with iOS 8 or higher (up to iOS 11) installed on iPhone 7, iPhone 7 Plus, iPhone SE, iPhone 6s, iPhone 6s Plus, iPhone 6, iPhone 6 Plus, iPhone 5s,...
  • Page 48 Displays the pop-up menu for Apple Music Radio. • Touch [Play More Like This] to play back songs similar to the current song. • Touch [Play Less Like This] to set it not to play back the current song again. •...
  • Page 49: Weblink

    Using WebLink Important • Pioneer is not liable for any issues that may arise from incorrect or flawed app-based content. • The content and functionality of the supported applications are the responsibility of the App providers. • In WebLink, functionality through the product is limited while driving, with available functions determined by the App providers.
  • Page 50 WebLink Displays the main menu of the WebLink source screen. When the rear display is connected to this unit, video from the WebLink screen can be displayed to the rear display except while the AV source with video content is active even while driving. For iPhone users System requirement iOS 10.0 or higher (up to iOS 11.x)
  • Page 51 • The video playback capability depends on the connected Android device. Unlock your smartphone and connect it to this product via USB. Refer to the Quick start guide. Press Touch Touch [WebLink]. Touch desired icon in the tab. The WebLink app is launched. Using the audio mix function You can output the audio mixing AV source and an application for iPhone or smartphone when WebLink is used.
  • Page 52: Apple Carplay

    • Apple CarPlay allows access to applications other than those listed that are subject to limitations while driving. • PIONEER IS NOT RESPONSIBLE AND DISCLAIMS LIABILITY FOR THIRD PARTY (NON-PIONEER) APPS AND CONTENT, INCLUDING WITHOUT LIMITATION ANY INACCURACIES OR INCOMPLETE INFORMATION.
  • Page 53 Touch [Driving Position]. Touch the item. [Left] Select for a left-hand drive vehicle. [Right] Select for a right-hand drive vehicle. Starting procedure Connect an Apple CarPlay compatible device to this product via USB. Press Touch Touch [Apple CarPlay]. Touch Apple CarPlay icon in the tab. The application screen appears.
  • Page 54 Touch to mute. Touch again to cancel mute. Touch [+]/[-] to adjust the guidance volume. Displays the main sound volume. To adjust the main sound volume, press VOL (+/-) on the unit or touch [+]/[-]. NOTE The volume menu is displayed for four seconds. If the menu disappears, press VOL (+/-) again. The menu reappears.
  • Page 55: Android Auto

    • Android Auto allows access to applications other than those listed that are subject to limitations while driving. • PIONEER IS NOT RESPONSIBLE AND DISCLAIMS LIABILITY FOR THIRD PARTY (NON-PIONEER) APPS AND CONTENT, INCLUDING WITHOUT LIMITATION ANY INACCURACIES OR INCOMPLETE INFORMATION.
  • Page 56 Touch [Driving Position]. Touch the item. [Left] Select for a left-hand drive vehicle. [Right] Select for a right-hand drive vehicle. Starting procedure Connect an Android Auto™ compatible device to this product via USB. Press Touch Touch [Android Auto]. Touch Android Auto icon in the tab. The application screen appears.
  • Page 57 Touch to mute. Touch again to cancel mute. Touch [+]/[-] to adjust the guidance volume. Displays the main sound volume. To adjust the main sound volume, press VOL (+/-) on the unit or touch [+]/[-]. NOTE The volume menu is displayed for four seconds. If the menu disappears, press VOL (+/-) again. The menu reappears.
  • Page 58: Aux

    You can display the video image output by the device connected to video input. CAUTION For safety reasons, video images cannot be viewed while your vehicle is in motion. To view video images, stop in a safe place and apply the handbrake. NOTE A Mini-jack AV cable (sold separately) is required for connection.
  • Page 59 Hides the touch panel keys. To display the keys again, touch anywhere on the screen. You can set the screen size for the video image (page 82). Switches between the video input and audio input. - 59 -...
  • Page 60: Av Input

    AV input You can display the video image output by the device connected to video or camera input. For details, refer to the Quick start guide. CAUTION For safety reasons, video images cannot be viewed while your vehicle is in motion. To view video images, stop in a safe place and apply the handbrake.
  • Page 61: Settings

    Settings You can adjust various settings in the main menu. Displaying the setting screen Press Touch Touch one of the following categories, then select the options. System settings (page 61) Theme settings (page 69) Audio settings (page 70) Video settings (page 77) Bluetooth settings (page 16) System settings The menu items vary according to the source.
  • Page 62 [Auto Mix] Menu Item Description [Auto Mix] Select whether to perform mixing the sound output from [On] [Off] WebLink and AV source sound automatically. [Input/Output settings] Menu Item Description [USB MTP] Select whether or not to activate USB MTP (Media Transfer [Off] [On] Protocol) connection.
  • Page 63 Touch this key to switch the display between the rear view image and 2nd camera image. CAUTION Pioneer recommends the use of a camera which outputs mirror reversed images, otherwise the screen image may appear reversed. • Immediately verify whether the display changes to the rear view camera image when the gearstick is moved to REVERSE (R) from another position.
  • Page 64 Menu Item Description [Parking Assist Guide Adjusting the guidelines by dragging or touching Adjust] on the screen. Touch [Default] to reset the settings. CAUTION • When adjusting the guidelines, be sure to park the vehicle in a safe place and apply the handbrake. •...
  • Page 65 • Depending on your vehicle, this function may not work properly. In this case, contact your dealer or an authorised PIONEER Service Station. • Please use a PIONEER wiring harness for each car model when [With Adapter] mode is engaged, otherwise select [W/o Adapter].
  • Page 66 Menu Item Description [Touch panel calibration] Touch [Yes]. Touch two corners of the screen along the arrows then touch the centres of the two [+] marks at the same time twice. Press The adjustment results are saved. Press once again. Proceed to 16-point adjustment.
  • Page 67 Menu Item Description [Dimmer Duration] Adjust the time that the dimmer is turned on or off by dragging the cursors or touching You can use this function when [Dimmer Trigger] is set to [Time]. TIPS • Each touch of moves the cursor backwards or forwards in the 15 minute width.
  • Page 68 Menu Item Description [Brightness] Adjust the black intensity. [-24] to [+24] [Contrast] Adjust the contrast. [-24] to [+24] [Colour]* Adjust the colour saturation. [-24] to [+24] [Hue]* Adjust the tone of colour (which colour is emphasised, red, [-24] to [+24] or green).
  • Page 69: Theme Settings

    Menu Item Description [Firmware Update] CAUTION • The USB storage device for updating must contain only the correct update file. • Never turn this product off, disconnect the USB storage device while the firmware is being updated. • You can only update the firmware when the vehicle is stopped and the handbrake is engaged.
  • Page 70: Audio Settings

    Menu Item Description (custom)*1 Displays the background display image imported from the external storage device. (off ) Hides the background display. [Illumination]*2 Select an illumination colour from the colour list or create a defined colour. Coloured Keys Select the desired preset colour. (custom) Displays the screen to customise the illumination colour.
  • Page 71 Menu Item Description [Graphic EQ] Select or customise the equaliser curve. [Super Bass (S.Bass)] Select a curve that you want to use as the basis of [Powerful] [Todoroki] customising then touch the frequency that you want to [Vocal] [Flat] [Custom1] adjust.
  • Page 72 Menu Item Description [Source Level Adjuster] Adjust the volume level of each source to prevent radical [-4] to [+4] changes in volume when switching between sources other than FM. Touch to adjust the source volume after comparing the FM tuner volume level with the level of the source.
  • Page 73 Menu Item Description [Time Alignment] Select or customise the time alignment settings to reflect [On] [Off] the distance between the listener’s position and each Listening Position*1*2 speaker. You need to measure the distance between the [Off] [Front Left] [Front head of the listener and each speaker unit. Right] [Front] [All] Touch to select the listening position then...
  • Page 74 Menu Item Description [Automatic Level Control] Corrects automatically the audio level difference between the music files or the sources. [Off] Turns the auto level control setting off. [Mode1] Corrects a little the audio level difference between the music files or the sources (for the narrow dynamic range audio signal).
  • Page 75 ▶Before operating the Auto EQ function • Perform Auto EQ in a quiet place with the vehicle engine and air conditioning switched off. Also, cut the power of car phones or mobile phones in the vehicle, or remove them in advance. Surrounding sounds may prevent correct measurement of the vehicle’s acoustics.
  • Page 76 Disconnect the iPhone or smartphone device. Turn on the ignition switch (ACC ON). If the vehicle’s air conditioner or heater is turned on, turn it off. Switch the AV source to [Source OFF] (page 26). Press Touch then Touch [A-EQ&TA Measurement]. Connect the microphone for acoustical measurement (sold separately) with this product.
  • Page 77: Video Settings

    NOTE [Subwoofer Settings] is available only when [Subwoofer] is [On]. Press Touch then Touch [Crossover] or [Subwoofer Settings]. Touch to switch the speaker. Drag the graph line to set the cutoff position. Drag the lowest point of the graph to set the cutoff slope. The following items can also be set.
  • Page 78 Menu Item Description [TV Aspect] Set the aspect ratio suitable for your rear display 16:9 (wide screen display) or 4:3 (regular display). (We recommend use of this function only when you want to fit the aspect ratio to the rear display.) NOTES •...
  • Page 79 Menu Item Description [Parental] Set restrictions so that children cannot watch violent or adult-oriented scenes. You can set the parental lock level in steps as desired. Touch [0] to [9] to input a four-digit code number. Touch Registers the code number, and you can now set the level.
  • Page 80 [Video Signal Setting] Menu Item Description [AV] Select the suitable video signal setting when you connect [Auto] [PAL] [NTSC] [PAL- this product to an AV equipment. M] [PAL-N] [SECAM] [AUX] Select the suitable video signal setting when you connect [Auto] [PAL] [NTSC] [PAL- this product to an AUX equipment.
  • Page 81: Favourite Menu

    Favourite menu Registering your favourite menu items in shortcuts allows you to quickly jump to the registered menu screen by a simple touch on the [Favourites] screen. NOTE Up to 12 menu items can be registered in the favourite menu. Creating a shortcut Press then touch...
  • Page 82 Other functions Setting the time and date Touch the current time on the screen. Touch to set the correct time and date. You can operate the following items: Year, month, date, hour, minute. TIPS • You can change the time display format to [12hour] or [24hour]. •...
  • Page 83 [Trimming] An image is displayed across the entire screen with the horizontal-to-vertical ratio left as is. If the screen ratio differs from the image, the image may be displayed partly cut off either at the top/bottom or sides. NOTE [Trimming] is for image files only. TIPS •...
  • Page 84 – Park your vehicle in a safe place and here, contact your dealer or the nearest apply the handbrake. authorised Pioneer service facility. No video output from the connected Common problems equipment. → The [AV Input] or [AUX Input] setting is incorrect.
  • Page 85 – The operation is not possible. (For The picture is extremely unclear/ example, the DVD playing does not distorted and dark during playback. feature that angle, audio system, → The disc features a signal to prohibit subtitle language, etc.) copying. (Some discs may have this.) –...
  • Page 86 If the error persists, screen operation. record the error message and contact your – Stop the vehicle in a safe place and dealer or your nearest Pioneer service check the screen on the smartphone. centre. The screen is displayed, but operation Common does not work at all.
  • Page 87 – Clean the disc. Video frame rate not supported → The disc is scratched. → DivX file’s frame rate is more than 30 fps. – Replace the disc. – Select a file that can be played. → The disc is loaded upside down. –...
  • Page 88 Pioneer Service Station. – Disconnect the USB storage device and do not use it. Turn the ignition Apple CarPlay switch to OFF, then to ACC or ON and then connect a compliant USB storage device.
  • Page 89 If the error message is still performing the above action, please displayed after performing on-screen contact your dealer or an authorised instructions, please reconnect the Pioneer Service Station. device. Android Auto Handling and care of discs Android Auto has stopped.
  • Page 90 • Playback of discs may not be possible because of disc characteristics, disc format, recorded application, playback environment, storage conditions and so • Road shocks may interrupt disc playback. • Read the precautions for discs before using them. AVCHD recorded discs Ambient conditions for playing a This unit is not compatible with discs recorded in AVCHD (Advanced Video...
  • Page 91 CD-R/CD-RW discs • Unfinalised discs cannot be played back. • It may not be possible to playback CD-R/ CD-RW discs recorded on a music CD recorder or a computer because of disc characteristics, scratches or dirt on the Detailed information disc, or dirt, scratches or condensation on for playable media the lens of the built-in drive.
  • Page 92 USB storage device compatibility • For details on the DivX video versions that can be played on this product, refer • For details about USB storage device to Specifications (page 100). compatibility with this product, refer to • For more details about DivX, visit the Specifications (page 100).
  • Page 93 SAMPLING FREQUENCY USB: 32 kHz to Media compatibility chart 48 kHz Disc: 8 kHz to General 48 kHz • Maximum playback time of audio file TRANSMISSION RATE USB: 8 kbps to stored in the disc: 60 h 320 kbps (CBR)/ •...
  • Page 94 • If a file contains more than 4 GB, playback .avi stops before the end. Compatible video codec MPEG4, DivX, • Some special operations may be H.264, H.263 prohibited because of the composition of Maximum resolution 1 920 × 1 080 DivX files.
  • Page 95 OR IMPLIED WARRANTIES, INCLUDING, BUT registered trademarks owned by Bluetooth SIG, NOT LIMITED TO, THE IMPLIED Inc. and any use of such marks by PIONEER WARRANTIES OF MERCHANTABILITY AND CORPORATION is under license. Other FITNESS FOR A PARTICULAR PURPOSE ARE trademarks and trade names are those of their respective owners.
  • Page 96 Download free software at www.divx.com to create, play and cast digital videos. • Pioneer accepts no responsibility for data lost from an iPod, even if that data is lost while using this product. Please back up your iPod data regularly.
  • Page 97 iPhone, iPod and Lightning Apple CarPlay Apple CarPlay is a trademark of Apple Inc. Use of the Made for Apple badge means that Use of the Works with Apple badge means an accessory has been designed to connect that an accessory has been designed to work specifically to the Apple product(s) identified specifically with the technology identified in in the badge, and has been certified by the...
  • Page 98 Content application(s) or Using app-based service by its provider. connected content • Pioneer is not liable for any issues that may arise from incorrect or flawed app- based content. Important • The content and functionality of the Requirements to access app-based...
  • Page 99 • Do not push the LCD screen with Notice regarding MP3 excessive force as this may scratch it. file usage • Never touch the LCD screen with anything besides your finger when operating the touch panel functions. The Supply of this product only conveys a LCD screen can scratch easily.
  • Page 100 Preout output level (max): 4.0 V visible. In that case, please consult your Equaliser (13-Band Graphic Equaliser): dealer or the nearest authorised Pioneer Frequency: Service Station. 50 Hz/80 Hz/125 Hz/200 Hz/315 Hz/ 500 Hz/800 Hz/1.25 kHz/2 kHz/3.15...
  • Page 101 <Network Mode> DVD drive HPF (High): System: Frequency: DVD-V, VCD, CD, MP3, WMA, AAC, DivX, 1.25 kHz/1.6 kHz/2 kHz/2.5 kHz/3.15 MPEG player kHz/4 kHz/5 kHz/6.3 kHz/8 kHz/10 kHz/ Usable discs: 12.5 kHz DVD-VIDEO, VIDEO-CD, CD, CD-R, CD- Slope: RW, DVD-R, DVD-RW, DVD-R DL -6 dB/oct, -12 dB/oct, -18 dB/oct, -24 Region number: 5 dB/oct...
  • Page 102 File system: FAT16, FAT32, NTFS MPEG4 video decoding format: <USB audio> Simple Profile, Advanced Simple Profile MP3 decoding format: MPEG2 video decoding format: MPEG-1 & 2 & 2.5 Audio Layer 3 Main Profile WMA decoding format: Bluetooth Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch audio) Version: (Windows Media Player) Bluetooth 4.1 certified...
  • Page 103 © 2019 PIONEER CORPORATION. All rights reserved. <OPMWEB_AVHZ5290BTXNID_engb_A> ID...

Table of Contents