Related Manuals for Huawei SmartAX MA5811S-AE08
Summary of Contents for Huawei SmartAX MA5811S-AE08
- Page 1 SmartAX MA5811S-AE08 Multi-service Access Module V800R017C10 Installation Guide Issue: 01 Date: 2016-09-14 HUAWEI TECHNOLOGIES CO., LTD.
-
Page 2: Table Of Contents
Contents 1. Precautions 2. Check Tools and Meters 3. Appearance and Structure 4. Installing the Chassis a. Installing the MA5811S-AE08 on a pole b. Installing the MA5811S-AE08 on the wall 5. Routing the Cables a. Routing a PGND Cable b. Connecting a Subscriber Cable c. -
Page 3: Precautions
Copyright © Huawei Technologies Co., Ltd. 2016. All rights reserved. -
Page 4: Check Tools And Meters
Before you begin, get the following tools ready. Marker Flat-head Phillips Diagonal screwdriver screwdriver pliers 5# (M6) wrench Crimping tool Paper knife Measuring tape 3# (M4) wrench Cable cutter ESD gloves Optical power Multimeter meter Impact tool Locking pliers Hammer drill (HUAWEI-JPX) -
Page 5: Appearance And Structure
Appearance and Structure Appearance 130 mm 330 mm 230 mm Internal Structure (without terminal block) Ground point Support for the Upstream optical port Maintenance serial port terminal block PGND cable entrance Optical fiber entrance Reserved Subscriber cable entrance... - Page 6 Appearance and Structure Internal Structure(with terminal block) Subscriber cable connector Terminal block Subscriber cable assembly Ground point Support for the Upstream optical port Maintenance serial port terminal block PGND cable entrance Optical fiber entrance Reserved Subscriber cable entrance...
-
Page 7: Installing The Chassis
Installing the Chassis Installing MA5811S-AE08 on a Pole Insert hose clamps into the mounting bracket. Use a hex key to fix the mounting bracket onto the pole. 5# (M6) wrench Trim excess hose clamps off. - Page 8 Installing the Chassis Installing MA5811S-AE08 on a Pole Wrap the clipped hose clamp using insulation tapes. Coiling the excess hose clamp on the pole and binding it using a cable tie is recommended for convenience of follow-up migration. Install the MA5811S-AE08 onto the mounting bracket. Use a Phillips screwdriver to fix the screws in the bottom of the mounting bracket.
-
Page 9: Installing The Ma5811S-Ae08 On The Wall
Installing the Chassis Installing MA5811S-AE08 on the wall Place the MA5811S-AE08 separate mounting bracket against the wall, verify that the mounting bracket is horizontally placed, and mark anchor points. Maker Drill holes on the wall according to marked installation points and Install M6 x 60 expansion bolts. (hole diameter: 8.5 mm;... - Page 10 Installing the Chassis Installing MA5811S-AE08 on the wall Install mounting kits into the wall. Mount the MA5811S-AE08 to the mounting kits and fasten the screws at the bottom of the mounting kits to complete the installation. Bottom view Note: Theoretically, the MA5811S-AE08 can be reversely installed. However, it can only be reversely installed indoors without any water leakage.
-
Page 11: Routing The Cables
Routing Cables Routing a PGND Cable The structure of the MA5811S-AE08 in the document is slightly different from the actual device; however, the difference does not affect device installation. Remove the cap from the waterproof Route the PGND cable through the cap of connector at the PGND cable entrance. -
Page 12: Connecting A Subscriber Cable
Routing Cables Routing a Subscriber Cable (MA5811S-AE08 without terminal block) Remove the cap from the waterproof connector at the subscriber cable entrance. Route the subscriber cable through the cap, waterproof connector, and device compartment. 350 mm 1. Install the terminal block to the support delivered in the package. (The terminal block should be provide by the user.) 2. - Page 13 Routing Cables Routing a Subscriber Cable (MA5811S-AE08 without terminal block) Pin assignments of the subscriber cable is shown in the following table. Color Relation Port Color Relation Port White Pair White Pair Blue Grey White Pair Pair Orange Blue White Pair Pair Green...
- Page 14 Routing Cables Routing a Subscriber Cable (MA5811S-AE08 with terminal block) Remove the cap from the waterproof connector at the subscriber cable entrance. Route the subscriber cable through the cap, waterproof connector, and device compartment. 350 mm Remove the support from the MA5811S-AE08.
- Page 15 Pin assignments of the subscriber cable is shown in the following table. Color Relation Port Color Relation Port White Pair White Pair Blue Grey White Pair Pair Orange Blue White Pair Pair Green Orange White Pair Pair Brown Green Impact tool (HUAWEI-JPX)
- Page 16 Routing Cables Routing a Subscriber Cable (MA5811S-AE08 with terminal block) 1. Install the support routed with subscriber cables to the device. 2. Install the connector of the subscriber cable to the subscriber port.
-
Page 17: Routing An Optical Fiber
Routing Cables Routing an Optical Fiber The MA5811S-AE08 supports 10G GPON, GPON, 10GE and GE upstream transmission. These four upstream transmission modes have different optical models and optical fibers but they have the same installation modes. The following uses GE upstream transmission as an example. GE upstream GPON upstream LC/UPC... - Page 18 Routing Cables Routing an Optical Fiber Entrance and route the optical fiber through Use a Phillips screwdriver to open the clip. the device compartment. Coil the optical fiber and fasten the Use the Phillips screwdriver to fasten the clip. waterproof connector.
-
Page 19: Checking The Installation
Checking the Installation Description Method No object must be placed on the chassis. Observe All the cables are bound with proper tightness. The space between the cable ties is even, and the remaining parts of the cable ties are cut off Observe neatly. -
Page 20: Checking Device Running Used Backup Power
Checking Device Running used local power After the MA5811S-AE08 is installed and the PSE does not supply power for the device, use the local power test port to test whether the device can run normally. Before the test, connect local power to the BATTERY hole. If the RUN/ALM indicator blinks green, on for 1s and off for 1s, the device can run normally. -
Page 21: Checking Upstream Port Optical Power
Checking Upstream Port Optical Power • When measuring Upstream port optical power, do not stand close to or look into the optical port without eye protection. • The MA5811S-AE08 optical power meets the following requirements: GPON: –27 dBm to –8 dBm ... -
Page 22: Checking Device Running
Checking Device Running Turn on the output switch of the AC power system that supplies for the MA5811S-AE08. Indicator status: •After the device is powered on, the RUN/ALM indicator starts (blinking green at an interval of 0.25s). About 4 minutes later, it is normal (blinking green at an interval of 1s). •If the upstream port mode is correct and the Rx optical power of the upstream port is within the normal range, see the following table the UPLINK indicator to check the upstream port status. -
Page 23: Faqs For Installation
Do not distort cables. The ends of the optical cables should be fiber that is not used should grounded. be protected with dustproof caps. HUAWEI TECHNOLOGIES CO., LTD. Huawei Industrial Base Bantian Longgang Shenzhen 518129 People's Republic of China www.huawei.com...