Use model and serial number in all correspondence and when ordering parts. To order replacement parts from an authorized TORO Distributor, supply the following information: Model and serial numbers of the machine.
Safety WARNING—Petrol is highly flammable. Training • Store fuel in containers specifically designed Read the instructions carefully. Be familiar with for this purpose. the controls and the proper use of the equipment. • Refuel outdoors only and do not smoke Never allow children or people unfamiliar with while refueling.
Page 4
• stay alert for bumps and hollows and other adjustment can be made from the operator’s hidden hazards; position. • never mow across the face of the slope, • before clearing blockages; unless the lawn mower is designed for this •...
Page 5
Sound & Vibration Levels Sound Levels This unit has a continuous A-weighted sound pressure level at the operator ear of: 84.2 dB(A), based on mea- surements of identical machines per Directive 91/386/EEC. This unit has a sound power level of 99 LWA, based on measurements of identical machines per procedures outlined in Directive 84/538/EEC and amendments.
Page 6
Symbol Glossary Caustic liquids, Poisonous Electrical shock, High pressure High pressure High pressure Crushing of Crushing of chemical burns to fumes or toxic electrocution fluid, injection spray, erosion of spray, erosion of fingers or hand, toes or foot, force fingers or hand gases, asphyxiation into body flesh...
Page 7
Eye protection Head protection Hearing Caution, toxic First aid Flush with water Engine Transmission must be worn must be worn protection must risk be worn Hydraulic Brake system Coolant (water) Intake air Exhaust gas Pressure Fire, open light & smoking system prohibited Level...
Page 8
Engine coolant Engine coolant f Engine Engine intake/ Engine intake/ Engine intake/ Engine start Engine stop pressure ilter lubricating oil combustion air combustion air air filter pressure pressure n/min Engine failure/ Engine rotational Choke Primer (start aid) Electrical preheat Transmission oil Transmission oil Transmission oil malfunction speed/frequency...
Specifications Power : 4-cycle gasoline engine, electric start, with accessory terminal is available at the leak detector output of 11.9 kW @3,600 rpm. Maximum no-load test switch if attachment of headlights is desired. governed engine speed is 2,850 rpm. Battery : 12-Volt, Lead Acid, 32-Amp.
Install the dipstick firmly in place. FILLING THE GAS TANK THE TORO COMPANY STRONGLY RECOMMENDS THE USE OF CLEAN, FRESH UNLEADED REGULAR GASOLINE IN TORO GASOLINE-POWERED PROD- UCTS. UNLEADED GASOLINE BURNS CLEANER,...
Page 11
fuel system damage could result. Fill the gasoline tank to the bottom of the filler neck. DO NOT OVERFILL. Install the cap and tighten it securely in place. DANGER Because gasoline is flammable, use caution when storing or handling lt. Do not fill the fuel tank while the engine is running, or hot, or when the machine is in an enclosed area.
Page 12
Phillips HG fluid Shell Donax TD Texaco Union Oil Hydraulic/Tractor fluid Note: The fluids within this group are interchangeable. Group 2 Hydraulic Fluid (Recommended for ambient temperatures consistently above 70° F) ISO type 68 anti-wear hydraulic fluid Figure 3 Mobil DTE 26 or DTE 16 1.
Page 13
One bottle is sufficient for 22 L of hydraulic fluid. Order Part No. 44-2500 from your Authorized Toro Distributor. Position the machine on a level surface. Make sure the machine has cooled down so fluid is cold.
Controls MOW PEDAL (Fig. 4)—Depressing the mow pedal FULLY during operation lowers the cutting units and starts the reels. BRAKE PEDAL (Fig. 4)—The brake pedal actuates an automotive drum-type mechanical brake. LIFT PEDAL (Fig. 4)—Depressing the lift pedal during operation stops the reels from turning and lifts the cutting units.
Page 15
circuit. LEAK DETECTOR TEST/LIGHT SWITCH (Fig. 6) From the middle operating position, move the switch rear- ward to check the operation of the leak detector alarm and time delay. Move the switch forward to operate optional headlights. HOUR METER (Fig. 6)—Shows the total hours of machine operation.
NOTE: When the Greensmaster 3100 is new and the Sit on the seat, place the shift selector in bearings and reels are tight, it is necessary to use the NEUTRAL, and check the mow and lift pedals to FAST throttle control position for this check.
Page 17
If the engine did not crank, go to step 3. If the engine cranked, contact your local TORO dealer for assistance. Sit on the seat, engage the parking brake, depress the lift pedal and release it.
Page 18
#2 position. If the engine does not stop, stop the engine and find the problem before operating the machine. If you need assistance, contact your local Figure 10 TORO dealer. BEFORE START (cold oil) 1. Sight window 2. Solenoid return valve open CHECK THE LEAK DETECTOR’S...
Page 19
1. Fluid level (warm) 2. Warning buzzer 3. Float down, switch closed Before mowing greens with the GREENSMASTER 3100, we suggest that you find a clear area and practice starting and stopping, raising and lowering the cutting units, turning, etc. This will help you gain confidence in the performance of the GREENSMASTER 3100.
Operating BEFORE MOWING important, so the mowers do not cut into the fringe area. However, as much of the green as possible should be cut to minimize the amount of grass left Inspect the green for debris, remove the flag from the cup, to mow around the outer periphery.
Page 21
brakes, etc. LEAK DETECTOR OPERATION The leak detector alarm may sound for one of the following reasons: A leak has occurred. The oil level in the main reservoir is reduced by 4 to 6 ounces due to oil contraction from cooling. If the alarm sounds, turn it off as quickly as possible and inspect for leaks.
Page 22
After you achieve the desired setting, hold the knob to prevent any rotation and tighten the jam nut. ADJUSTING LIFT CYLINDERS When in the raised (transport) position, the front lift cylinders may be adjusted. Lower the cutting units to the floor. Loosen the jam nut on the clevis of the cutting unit lift cylinder to be adjusted.
Maintenance Maintenance Schedule Maintenance Procedure Maintenance Interval & Service Check battery fluid level Every Every Every Every 50 Check battery cable connections hours Service the air filter pre-cleaner hours hours hours Lubricate all grease fittings Change the engine oil Replace the engine oil filter Replace the air filter element Check the reel bearing preload adjustment Torque the wheel lug nuts...