Figures - ABB A200-L Operation Manual

Operation Manual / A200-L

Figures

Figures
Fig. 1: Layout and function of the turbocharger ...... 6
Fig. 2: Locations of the rating plates ......................... 8
Fig. 3: Warning plate locations ................................... 13
Fig. 4: Rating plate ........................................................ 13
Fig. 5: Attachment of loads on the crane hook ....... 16
Fig. 6: Attachment angle.............................................. 16
Fig. 7: Fitting the lifting gear ...................................... 27
Fig. 8: Placing the turbocharger................................ 28
Fig. 9: Compressor-end foot...................................... 29
Fig. 10: Turbine-end foot ............................................ 29
Fig. 11: Oil temperature at the outlet ....................... 35
Fig. 12: Layout and overview of the speed measure-
ment system................................................................... 37
Fig. 13: Replacing the speed sensor ......................... 39
Fig. 14: U-tube manometer at the filter silencer .... 40
Fig. 15: Noise insulation, bellows .............................. 42
Fig. 16: Layout and overview of filter silencer ........ 50
Fig. 17: Dismantling filter ring circumferential part ....
52
Fig. 18: Opening filter ring lock.................................. 52
Fig. 19: Attaching new filter ring ............................... 53
Fig. 20: Fitting new filter ring .................................... 53
Fig. 21: Overview of wet cleaning of compressor .. 56
Fig. 22: Filter plug view................................................. 57
Fig. 23: Dry cleaning device ........................................ 59
Fig. 24: Drain pipe diagram ........................................ 62
Fig. 25: Weights of assemblies .................................. 72
Fig. 26: Dismantling the filter silencer casing ......... 73
Fig. 27: Fitting the filter silencer casing .................. 74
Fig. 28: Fitting the filter silencer casing .................. 75
Fig. 29: Fitting the filter silencer casing .................. 75
Fig. 30: Fitting the filter silencer casing .................. 76
Fig. 31: Fitting the filter silencer casing................... 76
Fig. 32: Fitting the bellows .......................................... 77
© Copyright 2021 ABB. All rights reserved.
Fig. 33: Dismantling the filter silencer....................... 78
Fig. 34: Dismantling the filter silencer ...................... 79
Fig. 35: Dismantling the wall insert (A255-L.. - A260-
L..) ..................................................................................... 80
Fig. 36: Moving out wall insert .................................... 81
Fig. 37: Putting down wall insert ................................ 81
Fig. 38: Dismantling the wall insert (A265-L.. - A280-
L..) ..................................................................................... 82
Fig. 39: Moving out wall insert .................................... 83
Fig. 40: Putting down wall insert................................ 83
Fig. 41: Putting down wall insert ................................ 84
Fig. 42: Dismantling the diffuser ............................... 85
Fig. 43: Measuring axial clearance A .......................... 86
Fig. 44: Removing the insulation (A275-L and smal-
ler)..................................................................................... 87
Fig. 45: Dismantling the gas inlet casing (275-L and
smaller) ............................................................................ 88
Fig. 46: Dismantling the nozzle ring (A275-L and
smaller) ............................................................................ 89
Fig. 47: Dismantling the gas inlet casing (A280-L) . 90
Fig. 48: Fitting the nozzle ring holder........................ 91
Fig. 49: Dismantling the nozzle ring .......................... 92
Fig. 50: Put down the nozzle ring ............................... 92
Fig. 51: Fitting the nozzle ring (A275-L and smaller)....
93
Fig. 52: Fitting the gas outlet casing (A275-L and
smaller) ............................................................................ 94
Fig. 53: Fitting the insulation (A275-L and smaller) .....
95
Fig. 54: Fitting the nozzle ring (A280-L) ................... 96
Fig. 55: Attaching the nozzle ring (A280-L) ............. 97
Fig. 56: Fitting the gas inlet casing (A280-L) ........... 98
Fig. 57: Measuring axial clearance A .......................... 99
Fig. 58: Fitting the diffuser........................................ 100
Fig. 59: Positioning wall insert.................................. 101
Fig. 60: Fitting the wall insert (A255-L.. - A260-L..) ......
102
HZTL4036_EN Revision T December 2021