Page 1
Digital Copier Operating Instructions (For Internet Fax) DP-2500/3000 Options DA-AR250/AS200/DS200/DS205/DS210/DS215/FG230/FG231/FK200/FK210/FS200/MD200 DA-NE200/PC200/PC210/SM08B/SM16B/SM28B/UC200/XN200/XT200; UE-410047/410048/403171 Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference. English...
IMPORTANT INFORMATION When requesting information, supplies or service, always refer to the model and serial number of your machine. The model and serial number plate (Main Name Plate) is located on the machine as shown below. For your convenience, space is provided below to record information you may need in the future for reference or troubleshooting.
Important Information ... 22 s Differences between Internet Fax and Regular Fax ... 22 s Transmitted Document Confirmation ... 22 s DP-2500/3000 Cannot Make a Phone Call via LAN ... 22 s Dual Port Communication ... 22 s Transmission Resolution ... 22 s Internet Mail Reception ...
Page 4
General Description ... 101 s Relay Network ... 102 s Setting up your DP-2500/3000 as an Internet Relay Station ... 104 s Setting Up Your Machine for Relayed Transmission ... 105 s Programming the End Receiving Station into your Auto Dialer ... 105 s Sending Documents via Internet Relay ...
Page 5
Printout Journals and Lists Journals and Lists ... 117 s Transaction Journal ... 117 s Communication Journal (COMM. JOURNAL) ... 121 s Phone Book List ... 123 s Group and Program List ... 125 s FAX Parameter List ... 126 Problem Solving Troubleshooting ...
Getting to Know Your Machine Safety Information denotes a potential hazard that could result in serious injury or death. WARNING • TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE. • TO MINIMIZE THE POSSIBILITY OF SHOCK OR DAMAGE TO THE MACHINE, IT MUST BE PROPERLY GROUNDED.
Safety Information denotes hazards that could result in minor injury or damage to the machine. CAUTION • THIS PRODUCT CONTAINS A LITHIUM BATTERY. DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS OF YOUR LOCAL SOLID WASTE OFFICIALS.
Page 8
GETTING TO KNOW YOUR MACHINE Safety Information denotes hazards that could result in minor injury or damage to the machine. CAUTION Do not install the machine near heating or an air conditioning unit. Avoid exposure to direct sunlight. Install the machine on a flat surface, leave at least 4 inches (10 cm) of space between the machine and other objects.
Function Key Any function can be started by first pressing Deferred Communication 01 = XMT 02 = Polling 03 = Advanced Communication Advanced Communication 02 = Mailbox 04 = Sub-Address XMT 05 = LAN Relay XMT Edit File Mode 01 = File List (Print/View) 02 = Change Time/Station 03 = Delete File 04 = Print File...
FEED ADD TONER ADD TONER ON LINE ON LINE CONTRAST INTERNET PRINTER ON LINE ON LINE DATA DATA ON LINE Indicator • Blinks: When sending or receiving faxes. • Used to select the original size manually. Touch Panel Display DP-3000...
Page 11
Control Panel Control Panel Power save • Used to switch the • Used to start or machine into energy select the saving mode. function and For more details, see sub-functions. page 33 of the These functions Operating Instructions are explained in (For Copier.) detail on page 9.
Copy the Pre-installation Information form found at the end of this section on page 15, record the MAC Address on the form and ask your network administrator to complete the remaining information on the form. The MAC Address of your DP-2500/3000 can be found on the 2nd page of the Fax Parameter List printout (press...
NOTE 1. To function as SMTP mail server, the DP-2500/3000’s email address must include its unique Host name within your company domain. This unique Host name must be registered within your network’s DNS (Domain Name System) server. Example: DP-3000@fax01.panasonic.com 2.
GETTING TO KNOW YOUR MACHINE Pre Installation Information Setup as POP3 Client To install the DP-2500/3000 as POP3 Client, the following network parameters need to be programmed on your network. • IP Address of the DNS Server (if not available, see Note 2) •...
Page 15
SERVER) to "1:Invalid". Then the machine will prompt you to enter the IP Address of the SMTP and POP Servers. 3. If required, the MAC Address of the DP-2500/3000 can be obtained from the 2nd page of the Fax Parameter List...
Page 16
: POP User Name. (Up to 40 characters) : POP Password. (Up to 10 characters) : The name assigned to your DP-2500/3000. (Up to 60 characters) : The information to be added to the Subject Line for all outgoing emails. (Up to...
Internet Communication Features Internet Fax Transmission The DP-2500/3000 allows you to transmit documents over the Internet to another Internet Fax or a PC. The document is first scanned and converted into a TIFF-F formatted image file, and then transmitted to the remote location as an attachment file to an email using MIME encoding.
When an incoming Internet Fax, email or a regular fax document is received, the DP-2500/3000, checks for the following: 1. First, the DP-2500/3000 checks whether a sub-address is included. If it is, it will look for a sub-address match within its auto dialer and will route the documents to the corresponding stations email address(s) and/or telephone number(s).
G3 Fax Network Scanner The DP-2500/3000 can be utilized as a network scanner by simply transmitting an image to a PC as TIFF-F attachment to an email. This feature was enhanced with an addition of a new Fax Parameter No. 164 (IFAX XMT HEADER), giving you a selection of whether to include the header when sending a document to an addressee in the same Domain as specified in the Default Domain parameter.
DP-2500/3000 via TCP/IP protocol. There are two parts to setting up the DP-2500/3000 as a network printer. Part 1 requires you to download the software (printer driver and LPR) from the web site listed below.
Relayed Transmission The DP-2500/3000 allows you to transmit an email received from an Internet Fax or PC connected to the LAN to multiple fax machines via a telephone line. You can attach files with the TIFF-F format to this email.
Normal. Internet Mail Reception 1. The DP-2500/3000 can receive text email from a PC and print ANSI characters. It will print a "n " symbol if an unrecognized character is received. 2. Received email font and character size are fixed and cannot be changed.
TIFF-F formatted image file. An Image data in TIFF-F format has been attached to this email. You can download the TIFF-F Image Viewer from the following URL addresses: http://www.panasonic.co.jp/mgcs/internetfax/ http://www.panasonic.com/internetfax/ Internet Relayed Transmission To prevent unauthorized stations from accessing your Relay Station for Internet Relayed Transmission, you must set up your Network security.
GETTING TO KNOW YOUR MACHINE Connecting the LAN Cables ACTIVITY Lamp Blinks when there is data traffic on the LAN. LINK Lamp Illuminates when connected to the LAN. Lamp will not turn ON if LAN cable is defective (contains breaks). LAN Connection Jack (10Base-T/100Base-TX) LAN Cable...
Installing Your Machine User Parameters Setting the User (Internet) Parameters See Operating Instructions (For Facsimile) if you wish to set the basic settings (User Parameters). Before starting, you will need a completed copy of page 15 (Pre Installation Information). For your machine to be able to operate on the Network properly, the following five (5) Basic Parameters must be pre-programmed into the machine.
Page 26
INSTALLING YOUR MACHINE User Parameters Enter the IP Address using the keypad. 1 2 3 1 7 8 2 4 0 0 0 3 (See Note 2) To advance to the next parameter, press to return to Step 3 or press CANCEL return to standby.
Setting the Internet Parameters Setting the User Parameters for the LAN Interface Depending on how the DP-2500/3000 will be configured to communicate on the LAN, the appropriate parameters listed in the table below must be stored first. (See pages 12 to 17) Parameter DATE &...
• Relay Domain (up to 10 Domain Names authorized for Relay XMT Request) The DP-2500/3000 interprets the command that you enter in the "Subject:" line of your email message and performs one of the following functions, it Retrieves or Stores data into the Internet Parameters (User Parameters).
Programming or Retrieving Parameters via Email To Input the Internet Parameters for the First Time Create a script in the message body of a plain text email and send it to the DP-2500/3000’s email address. The "Subject:" line of the email must be as follows: #set parameters(password)#: Where the "password"...
Page 30
Turn "Off" the automatic line feed, or define the number of characters per line to prevent a line feed, or the data will be ignored. : The DP-2500/3000’s email address : This field is normally not visible when creating new email message(s). It is your default email address for retrieving the Internet Parameters and for error message notification.
Programming or Retrieving Parameters via Email To Retrieve the Internet Parameters for Backup To retrieve the existing Internet Parameters, send a plain text email to the DP-2500/3000’s email address with the following command in the "Subject:" line: #get parameters(password)# : Where the "password" is the Remote Password programmed in the DP- 2500/3000’s User Parameters (i.e.
Page 32
INSTALLING YOUR MACHINE Programming or Retrieving Parameters via Email After receiving the email message requesting the Internet Parameters, the DP-2500/3000 sends back an email to the address specified in the "From:" line with the Internet Parameters in the body of the email.
Programming or Retrieving Parameters via Email To Edit the Retrieved or Backup Internet Parameters File After receiving the DP-2500/3000 email with the Internet Parameters, store the email file as text (.txt) on your PC for backup purposes. To change or update the Internet Parameters, follow the steps below: 1.
Page 34
INSTALLING YOUR MACHINE Programming or Retrieving Parameters via Email DP-2500/3000 Internet Parameters Email Sample [Delete this header before sending email.]...
Page 35
(Notice that for the above example, we have changed the Manager’s Email Address, Relay XMT Password and the Remote Password). : This header must be deleted before the email is sent to the DP-2500/3000 for reprogramming of Internet Parameters. The information following the "#" sign is ignored by the DP-2500/3000, therefore, you can leave it as is or delete it if you wish.
PC by sending a text email message to the DP-2500/3000. The DP-2500/3000 interprets the command that you enter in the "Subject:" line of your email message and performs one of the following functions, it Retrieves or Stores data into the Auto Dialer (Phone Book).
Programming or Retrieving Parameters via Email Deleting the Entire Auto Dialer If you wish to delete the entire Auto Dialer data in the DP-2500/3000, type the following command in the body of the email message: @command delete @end This command can also be inserted before the @begin to @end block, to erase the entire Auto Dialer data first, then reprogramming it with new data.
Programming or Retrieving Parameters via Email To Program Phone Book for the First Time Create a script in the message body of a plain text email and send it to the DP-2500/3000’s email address.The "Subject:" line of the email must be as follows:...
Page 39
Programming or Retrieving Parameters via Email Explanation of Contents (1) To : The DP-2500/3000’s email address. From : This field is normally not visible when creating new email message(s). It is your default email address for retrieving the Phone Book data and for error message notification.
Programming or Retrieving Parameters via Email To Retrieve Phone Book Data for Backup To retrieve the existing auto dialer data, send a plain text email to the DP-2500/3000’s email address with the following command in the "Subject:" line: #get abbr(password)# Make sure that the "Cc..., Bcc..."...
Page 41
: Defines Phone Book programmed in the DP-2500/3000 in section (2) between @begin to @end block. (3) @program to @end : Defines Program Keys stored as a Group Key or POP Access Key programmed in the DP-2500/3000 in section (3) between @program to @end block.
Programming or Retrieving Parameters via Email To Edit the Retrieved or Backup Phone Book Data File After receiving the DP-2500/3000 email with the auto dialer data, store the email file as text (.txt) on your PC for backup purposes. To change or update the auto dialer, follow the steps below: Create a New Email Message, fill out the "To..."...
Page 43
(5) This header must be deleted before the email is sent to the DP-2500/3000 for reprogramming of Phone Book. The information following the "#" sign is ignored by the DP-2500/3000, therefore, you can leave it as is or delete it if you wish.
Programming or Retrieving Parameters via Email Using Email to Retrieve the Journal To retrieve the existing Journal data, send an email to the DP-2500/3000’s email address with the following command in the "Subject:" line: #get jnl(password)#: Where the "password" is, the Remote Password programmed in the DP-2500/3000’s User Parameters (i.e.
Make sure that the INTERNET lamp is ON. If not, press EDIT PHONE BOOK Enter the email address by using the QWERTY keyboard and then press (Up to 60 characters) Ex: abc@panasonic.com Continued on the next page... to select the "INTERNET MODE". 02 ADD EMAIL ADDR. SELECT A FUNCTION DEFERRED COMM.
Page 46
PROGRAMMING YOUR MACHINE Phone Book Then enter the station name by using the QWERTY keyboard. (Up to 15 characters) S A L E S SPACE Then enter the key name (up to 10 characters) . (By default, the key name is the first 10 characters of the station’s name.
(Note: The word "Email" above the key name, indicates that the key contains an email address) Email SALES DEPT Then enter a new email address. (See Note 1) Ex: xyz@panasonic.com Continued on the next page... PROGRAMMING YOUR MACHINE to select the "INTERNET MODE". 03 MODIFY STATION SELECT A FUNCTION DEFERRED COMM.
Page 48
PROGRAMMING YOUR MACHINE Phone Book Then enter a new station name. (See Note 1) P A N A F A X Then enter a new key name. (See Note 1) P A N A F A X To return to standby, press (see Note 1) (see Note 2) NOTE...
Page 49
EDIT FILE MODE PRINT OUT SET MODE EDIT PHONE BOOK DELETE STATION Email Email AMERICA ASIA CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email Email APOLLO CANADA CANCEL DELETE STATION PROGRAM DIAL Email SALES DEPT CANCEL DELETE STATION SALES DEPT abc@panasonic.com DELETE?
Page 50
PROGRAMMING YOUR MACHINE Phone Book To return to standby, press STOP (see Note 1) NOTE 1. If the Phone Book station has been used for a communication reservation, the settings cannot be changed or erased until the communication has finished. To change or erase the settings, cancel the communication first by Edit File Mode.
Customizing Your Machine Your facsimile machine has a variety of adjustable Fax Parameters. These parameters, listed in the Parameter Table, are preset for you and do not need to be changed. If you do want to make a change, read the table carefully.
Page 52
PROGRAMMING YOUR MACHINE Customizing Your Machine Select the desired setting. To advance to the next parameter, press to return to Step 3 or press standby. (see Note 1) (see Note 2) NOTE 1. To scroll the display to the desired Fax Parameters in Step 3, press 2.
Customizing Your Machine Fax Parameter Table Setting Parameter Number CONTRAST RESOLUTION ORIGINAL STAMP MEMORY DIALING METHOD HEADER PRINT HEADER FORMAT RCV'D TIME PRINT KEY/BUZZER VOLUME COMM. JOURNAL AUTO JOURNAL PRINT FILE ACCEPTANCE REPORT Continued on the next page... PROGRAMMING YOUR MACHINE Setting Lighter Setting the home position for the CONTRAST.
Page 54
PROGRAMMING YOUR MACHINE Customizing Your Machine Parameter RECEIVE MODE SUBSTITUTE RCV PRINT REDUCTION REDUCTION RATIO POLLING PASSWORD POLLED FILE SAVE STAMP AT MEM. XMT INCOMPLETE FILE SAVE XMT REDUCTION RING PATTERN DETECT (DRD) (See Note 2) RCV TO MEMORY ACCESS CODE PIN CODE ACCESS Setting Setting...
Page 55
Invalid Selecting whether the machine performs selective reception. Valid Setting the password for Remote Diagnostic Mode. Please ask (----) your Panasonic Authorized Dealer for details. Setting a 20-digit password for secured sub-address (----) communication. Invalid Selecting whether the machine performs FAX Forwarding to the specified destination.
Page 56
PROGRAMMING YOUR MACHINE Customizing Your Machine Parameter LINE SELECTION (See Note 4) LIST OUTPUT TRAY DUPLEX PRINT SPECIAL TRAY No. 1 - 3 MEMORY SIZE (Flash Memory) LAN RELAY XMT REQUEST LAN XMT REDUCTION RELAY XMT (a.k.a. LAN RELAY STATION on UF-770i) RELAY XMT REPORT EMAIL CHARACTER SENDER SELECTION...
Page 57
Valid Selecting the header information to print when an email is received. (Normally used for Troubleshooting. It shows the path of the email transmission before arriving at the DP-2500/3000.) Subject/From/ Invalid Selecting whether to automatically route a received fax or email using ITU-T sub-address.
Page 58
PROGRAMMING YOUR MACHINE Customizing Your Machine Parameter ROUTING HEADER IFAX XMT HEADER (Email only) (see Note 1) (see Note 2) (see Note 3) (see Note 4) NOTE 1. Setting number marked with an asterisk (*) indicates the factory standard setting. 2.
Basic Operations Sending Documents via LAN Document(s) can be sent via LAN to a single or multiple email addresses. The following Email Addressing methods can be selected: • Manual Email Addressing • Phone Book Email Addressing • Multiple Station Email Addressing Memory Transmission mode is always selected when sending document(s) to an email address via LAN.
BASIC OPERATIONS Sending Documents via LAN Manual Email Addressing To enter the email address manually, follow the steps below. Make sure that the INTERNET lamp is ON. If not, press (See Note 1) Place original(s) face up on the ADF. Place a book or an original face down on the Platen Glass.
Page 61
Enter the User portion of the email address and press the machine will complete the email address with the Default Domain preprogrammed in the User (Internet) Parameters. (i.e. will add "@panasonic.com" to the email address) (See Note 4) Ex: abc If you want to send to a different Domain, press to display a Selectable Domains list.
Page 62
5. To use the Parameters (see page 27). 6. The "Quick Memory Transmission" is disabled if multipe stations are set. key efficiently, the Selectable Domains must first be preprogrammed in the User (Internet) MEMORY XMT PAGE= abc@panasonic.com Email Email AMERICA ASIA CHINA...
(Note: The word "Email" above the key name, indicates that the key contains an email address) Email PANASONIC If the key name for the station that you want to send to is not displayed on the LCD, press scroll to the desired display page.
Page 64
BASIC OPERATIONS Sending Documents via LAN The document(s) begin to store into memory with a file number. Then starts connecting to the LAN immediately after storing the first page. (See Note 3) While sending the document(s) via LAN, the remaining page(s) continue to store into memory. (see Note 1) (see Note 2) (see Note 3)
READY TO FAX ORIGINAL SET Email AMERICA AFRICA Email ANTARCTICA BRAZIL Email APOLLO MEMORY XMT STATUS KEYBOARD ORIGINAL MEMORY XMT PANASONIC abc@panasonic.com after Email PANASONIC Email SALES DEPT MEMORY XMT STATUS KEYBOARD XMT MODE ORIGINAL (see Note 4) Email ASIA...
BASIC OPERATIONS Sending Documents via LAN Selectable Domains Key Using the Selectable Domains key often used Domain Names. • Advance registration of up to 10 often used domain names into the "Selectable Domain" list is required. (See page 27) Ex: Completing the "matsushita" email address with "@mgcs.co.jp" registered in the Selectable Domains key Make sure that the INTERNET lamp is ON.
Page 67
Sending Documents via LAN DONE To specify other destinations, press pressing and add additional email DONE addresses. The document(s) begin to store into memory with a file number. Then starts connecting to the LAN immediately after storing the first page. (See Note 3) While sending the document(s) via LAN, the remaining page(s) continue to store into memory (see Note 1)
BASIC OPERATIONS Sending Documents via LAN Internet Fax Ledger Size Document Transmission When transmitting via LAN, the transmitter is incapable of identifying the receiver's recording paper size capability, and thus it will not reduce the document size during transmission. Therefore, it is recommended that you send only A4/Letter size documents for LAN transmission.
Page 69
Document Size Transmission LEDGER EMAIL XMT = OFF Fax Parameter No. 141 (LAN XMT REDUCTION) set to "Invalid" LEDGER A4/Letter A4/Letter BASIC OPERATIONS MEMORY XMT STN(S):001 AMERICA panasonic.usa@panasonic.com Email Email AMERICA ASIA CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email...
BASIC OPERATIONS Sending Documents via LAN Returned Email When using the Internet communication mode, a failure report will print automatically for each transaction if the email is returned undelivered by the mail server. The printout will consist of the undelivered message contents supplied by the mail server and a portion of the first page’s image for that particular transaction.
BASIC OPERATIONS Sending Documents via LAN Using a Mailing List Using a Mailing List stored in the mail server simplifies the process of entering multiple locations and allows you to send to an unlimited number of email addresses with one easy operation. Ask your Network System administrator for information on how to utilize the Mailing List.
The DP-2500/3000 offers you a choice to receive Fax documents unattended (by default) or manually over regular telephone lines. The DP-2500/3000 also offers the same choice to receive and print Internet email messages via LAN unattended or manually when subscribing to a POP mail server. However, when the DP-2500/3000 is configured to receive email using SMTP protocol, the email can only be received and printed unattended.
Page 73
License agreement of Panasonic’s TIFF-F Image Viewer application You must carefully read the license agreement before installing the TIFF-F Image Viewer application on your PC. If you do not agree to all the terms of this agreement, do not use the software and destroy all of the copies thereof.
If "0 minutes" is entered, the POP server is not checked for mail. No. 147 (AUTO POP RCV): When there is mail to be retrieved from the POP server, the DP-2500/3000 will retrieve it and print the email unattended. If this parameter is set to "1:Invalid", the machine will not retrieve it, but displays the number of mails on the POP server.
Page 75
Receiving Documents via LAN Press to scroll the display to the desired Fax Parameter. 146 POP TIMER enter the Fax Parameter number directly from the keypad and press Enter the desired retrieval interval time (0 to 60 minutes) from the keypad and press If you make a mistake, press time interval and then re-enter the correct value.
Page 76
Either retrieve these mails from your PC or set the Fax Parameters to "Valid" triggering your DP-2500/3000 to receive, print and delete all the mails from the POP server. This procedure, however, might cause mail that had been printed before to print again.
Receiving Documents via LAN Unattended Email Retrieval from the POP Server When the Fax Parameter No. 146 (POP TIMER) is set to a value between 1 and 60 minutes, and Fax Parameter No. 147 (AUTO POP RCV) is set to "Valid", the machine will query the POP server at the specified interval for new mail.
Page 78
CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email Email APOLLO CANADA MEMORY XMT STATUS LIGHTER DARKER XMT MODE ORIGINAL KEYBOARD ON LINE(LAN) abc@panasonic.com Email Email AMERICA ASIA CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email Email APOLLO CANADA MEMORY XMT...
Setting the POP Email Retrieval Key This function allows others to share the DP-2500/3000 to retrieve their emails from the POP server by preprogramming their POP User Names and POP Passwords into the Program Dial keys. They will be able to retrieve their emails by simply pressing the associated Program Dial key.
Page 80
ADVANCED FEATURES Program Keys Enter the POP user name (up to 40 characters) and press Ex: POP1 Enter the POP key name (up to 10 characters) and press first 10 characters of the POP user name. If you do not want to change it, press Enter the POP password (up to 10 characters) and press Ex: 1111...
Program Keys Using the POP Email Retrieval Key To retrieve your Email from the POP Server using the Program Key, follow the procedure below. Make sure that the INTERNET lamp is ON. If not, press Press the Program key programmed for POP Email Retrieval Key.
Page 82
CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email Email APOLLO CANADA MEMORY XMT STATUS XMT MODE ORIGINAL LIGHTER DARKER KEYBOARD ON LINE(LAN) abc@panasonic.com Email Email AMERICA ASIA CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email Email APOLLO CANADA MEMORY XMT...
Sender Selection General Description This operation allows the user to select one of the 25 preset User Names and Email Addresses before a transmission. The selected User Name is printed on the Header of each page sent and on the COMM. Journal. When sending email, the selected user name and/or email address appears in the "From:"...
Page 84
S A L E S Enter an email address to be printed on the "From" field of the email message (max. 60 characters) and press Ex: abc@panasonic.com To record another User Name, repeat Steps 5 to 7. To return to standby, press STOP...
"INTERNET MODE". OCT-12-2000 15:00 READY TO FAX ORIGINAL SET Email Email AMERICA ASIA CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email Email APOLLO CANADA MEMORY XMT STATUS LIGHTER DARKER KEYBOARD ORIGINAL SELECT SENDER 00 PANASONIC 01 SALES DEPT CANCEL 01/05...
Page 86
2. If you do no select a User Name in Step 4, the unit selects the default User Name (00) that was programmed in the User Parameters for ordinary transmission. to scroll the display to select the NO.01 SALES DEPT sales@panasonic.com 00 PANASONIC 01 SALES DEPT CANCEL 01/05...
Panafax Engineering ************************************ -HEAD OFFICE Explanation of Contents (1) Sender Selection Number (2) User Name (3) Email Address to select the "INTERNET MODE". EMAIL ADDRESS sales@panasonic.com service@panasonic.com account@panasonic.com engneering@panasonic.com -PANASONIC - ***** - : 01-24 : Up to 25 characters...
Subject Line Entry General Description The DP-2500/3000 will automatically add the Default Subject information that was entered during the User Parameter setup, to the "Subject:" Line of all outgoing emails. If you would like for the machine to prompt you for the Subject before each email transmission, change the Fax Parameter No.
Page 89
Subject Line Entry Enter the Subject (max. 40 characters and digits) by using the QWERTY keyboard and keypad. To use the Default Subject pre-programmed in the User Parameter, just press Ex: FAX From Mr. Jones The document(s) begin to store into memory with a file number.
Setting the Routing Parameters The DP-2500/3000 can route documents received from a G3 fax machine to email address(s) or to Internet Fax machine(s) connected to a LAN as an email, as well as to other G3 fax machine(s) over the telephone line.
Page 91
Enter an email address (up to 60 characters) or a telephone number (up to 36 digits) and press Continued on the next page... ADVANCED FEATURES PHONE BOOK ENTER EMAIL ADDRESS PHONE BOOK ENTER TEL. NO. PHONE BOOK ENTER EMAIL ADDRESS abc@panasonic.com PHONE BOOK ENTER TEL. NO. 55512342762_...
Page 92
ADVANCED FEATURES Inbound Routing Then enter the station name using the QWERTY keyboard (up to 15 characters). S A L E S SPACE Then enter the key name (up to 10 characters). (By default, the key name is the first 10 characters of the station's name.
Page 93
ADVANCED FEATURES Inbound Routing To return to stanby, press STOP (see Note 1) NOTE 1. "+" and "SPACE" entries in the "ROUTING: TSI" field are ignored by the receiving machine.
ADVANCED FEATURES Fax Forward Setting Fax Forward This feature allows all incoming faxes or emails to be forwarded to the destination station registered in the Phone Book. Once the faxes or emails are received into memory, the machine will forward the received document(s) to the telephone number or email address pre-registered in the Phone Book.
Page 95
3. It is not possible to receive a document if the memory of your machine overflows or is about 95% used. ADVANCED FEATURES 054 FAX FORWARD INVALID VALID CANCEL 054 FORWARD ENTER STATION Email PANASONIC Email SALES DEPT MEMORY XMT STATUS XMT MODE ORIGINAL LIGHTER DARKER...
ADVANCED FEATURES Ifax Return Receipt The DP-2500/3000 automatically sends an Ifax Return Receipt to the sender confirming email reception from another Panasonic Internet Fax. To disable this feature, follow the steps below. Make sure that the INTERNET lamp is ON. If not, press...
Page 97
(see Note 1) NOTE 1. The DP-2500/3000 sends the Ifax Return Receipt only when receiving from another Panasonic brand Internet Fax. It will not confirm email sent from a PC. (The default setting for this parameter is "VALID".) ADVANCED FEATURES...
Page 98
ADVANCED FEATURES This page is intentionally left blank.
Network Features Network Scanner You can import Fax images by using the DP-2500/3000 transmission function. Storing a specific email address into a Phone Book allows you to import picture images by pressing a single key. Internet Fax DP-2500/3000 Place original(s) face up on the ADF.
(see Note 1) (see Note 2) NOTE 1. The DP-2500/3000 is unable to receive print jobs while it is engaged in a communication task. After the communication job is completed, the PC will transfer the print job to the DP-2500/3000 for printing.
G3 fax machines. This is especially true if the transmissions are long distance. You can send documents to any G3 fax machine by using the Internet via a LAN from your DP-2500/3000 to another Relay Station (DP-2500/3000).
G3 Fax machines. By simply sending a Document(s) from your DP-2500/3000 or an email message from a PC, to the DP-2500/ 3000 (Relay machine), which is then transmitted by the DP-2500/3000 to the end receiving station(s) using regular phone lines as a normal G3 Fax message.
Page 103
NOTE 1. The Relay XMT Password must be registered for the DP-2500/3000 to work as a Relay Station (see page 106). 2. To prevent unauthorized stations from accessing your Relay Station for Internet Relayed Transmissions, you must setup your network security. Enter acceptable Domain Name(s) and the Manager’s Email Address for notification of all Internet Relayed Transmissions (see page 104).
Domain Name of rdnn.mgcs.co.jp, rdmg.mgcs.co.jp or panasonic.com. NOTE 1. This should be different than the DP-2500/3000’s Email Address used to receive regular email / Internet Fax, as DP-2500/3000’s Email Address is always included in the header of all email messages sent. So, anyone receiving an Internet Fax from the machine will easily know the Relay XMT Password if it is the same as the Email Address.
Relayed Transmission Setting Up Your Machine for Relayed Transmission Programming the End Receiving Station into your Auto Dialer If the Fax Parameter No. 140 (LAN RELAY XMT REQUEST) is set to "Valid", you can enter the Relay Address into the Phone Book by the following procedure. To set a Phone Book for Relayed Transmission Request Make sure that the INTERNET lamp is ON.
Page 106
NETWORK FEATURE Relayed Transmission Then enter the station name by using the QWERTY keyboard (up to 15 characters). O M E Then enter the key name (up to 10 characters) . (By default, the key name is the first 10 characters of the station’s name.) If you do not want to change it, press Enter the Phone Book station of the Relay Station...
Page 107
NETWORK FEATURE Relayed Transmission To record another number, repeat Steps 3 to 7. To return to standby, press STOP...
CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email Email APOLLO CANADA MEMORY XMT STATUS LIGHTER DARKER KEYBOARD ORIGINAL MEMORY XMT STN(S):001 STOCKHOLM 4681111234 Email Email PANASONIC STOCKHOLM Email Email ROMA SYDNEY Email SG-RELAY Email SINGAPORE STATUS KEYBOARD ORIGINAL LIGHTER DARKER...
Page 109
1. If the Relay Station requires a special access number to get an outside line, enter that access number first then press to enter a pause (represented by a "-") before entering the full number. PAUSE (Telephone number) (see Note 1) : uk-rly@london.panasonic.co.uk NETWORK FEATURE...
KEYBOARD ORIGINAL LAN RELAY XMT ENTER RELAY STATION Email Email AMERICA ASIA CHINA AFRICA BERLIN Email Email ANTARCTICA BRAZIL Email Email APOLLO CANADA STATUS KEYBOARD ORIGINAL LIGHTER DARKER RELAY STATION LONDON RELAY uk-rly@london.panasonic.co.uk Email LONDON RLY STATUS KEYBOARD ORIGINAL LIGHTER DARKER...
Page 111
2. The "#" character is not available for the email address of the relay station. Email PANASONIC Email ROMA Email SG-RELAY Email SINGAPORE after STATUS number) (see Note 1) : uk-rly@london.panasonic.co.uk NETWORK FEATURE LAN RELAY XMT STN(S):001 STOCKHOLM 4681111234 Email STOCKHOLM Email SYDNEY LIGHTER DARKER KEYBOARD ORIGINAL...
(see Note 1) (see Note 2) NOTE 1. The "#" and "*" symbol must be entered after the Relay XMT Password as it indicates to the DP-2500/3000 that a phone number for the End Receiving Station will follow. 2. If the Relay Station requires a special access number to get an outside line, enter that access number first then enter a hyphen (represented by a "-") before entering the full number.
Page 113
A TIFF Converter software is used on your PC to convert document(s) into a "TIFF" file format, which allows the Internet FAX to receive the document as an attachment to an email. When you are sending a detailed graphic document(s) to a DP-2500/3000, DX-2000 or a DX-1000, you can specify 400 dpi resolution for better clarity.
2. Transmission Journal When the Relay Station receives instructions for a relayed transmission, a notification is emailed to the registered manager (see "Setting up your DP-2500/3000 as an Internet Relay Station" on page 104). Sample Relay XMT Report (COMM. JOURNAL) ************** -COMM.
Page 115
Relayed Transmission Sample Relayed Transmission Notification Email to a Manager Explanation of Contents (1) Email address of the sender’s Internet Fax (DP-2500/3000) or PC (2) End Receiving Station’s G3 fax telephone number(s) NETWORK FEATURE...
Page 116
NETWORK FEATURE This page is intentionally left blank.
Printout Journals and Lists Journals and Lists To help you maintain records of the documents you sent and received, as well as lists of the numbers you record, your facsimile machine is equipped to print the following journals and lists: Transaction Journal, Individual Transmission Journal, Communication Journal, Phone Book List, Program List, Fax Parameter List and File List.
Page 118
PRINTOUT JOURNALS AND LISTS Journals and Lists 02 XMT ONLY 03 ALL to view all transactions You can view the transactions in the journal by pressing standby. (see Note 1) Date & Time 03-12 10:00 Type of Communication XMT : Transmission RCV : Reception POL : Polling PLD : Polled...
Page 120
PRINTOUT JOURNALS AND LISTS Journals and Lists Explanation of contents (1) Printout date (2) Printout time (3) Journal number (4) Communication result (5) Number of pages transmitted or received (6) File number (7) Duration of communication (8) Type of communication (9) Remote station identification (10) Communication date (11) Communication Start time...
Page 122
PRINTOUT JOURNALS AND LISTS Journals and Lists Explanation of contents (1) Indication of communication mode (2) Start time of communication (3) End time of communication (4) File number (5) Station number (6) Communication result (7) One-Touch/Abbreviated number ¤ mark (8) Recorded name in the Phone Book, direct dialing number, or email address (9) Number of pages transmitted or...
Journals and Lists Phone Book List To print a Phone Book List of telephone numbers and email addresses you have stored Make sure that the INTERNET lamp is ON. If not, press PRINT OUT 02 PHONE BOOK LIST Continued on the next page... PRINTOUT JOURNALS AND LISTS to select the "INTERNET MODE".
DELETE E-MAIL : Invalid ----- DELETE E-MAIL : Valid GROUP ----- [PANAFAX][PANASONIC] -PANASONIC - ***** - : Up to 15 characters : "GROUP" indicates that the Program key is programmed as a group key. "POP" indicates that the Program key is programmed as a POP access key.
XMT MODE ORIGINAL KEYBOARD CURRENT STANDARD SETTING 3:S-Fine) 3:Photo) -PANASONIC 201 555 1212- ********* : "----" indicates code or password is not set. When the code or password is set, it is represented by asterisk(*). : Factory preset standard setting SETTING...
Page 127
Address, change the Fax Parameter No. 161 (DNS SERVER) to "Invalid". PRINTOUT JOURNALS AND LISTS GMT-5:00 Eastern Time (US & Canada) 080023000FF9 123.178.240.3 255.255.255.255 smtp.mgcs.mei.co.jp 172.21.22.1 fax@mgcs.co.jp 133.185.247.45 (See Note 1) pop.mgcs.mei.co.jp Panasonic ***** ifax001 Internet Fax from Sales Dept. panasonic.com mgcs.co.jp panasonic.co.jp ***** ***** ifaxadmin@mgcs.co.jp panasonic.co.jp mgcs.co.jp...
Page 128
PRINTOUT JOURNALS AND LISTS This page is intentionally left blank.
1. After identifying the problem and verifying the recommended action, if the Information Codes keep re-occurring or for help on Information Codes that appear on your machine but are not listed above, please contact your local Panasonic Authorized Dealer. Action Check the registered email address.
Troubleshooting Email ABBR Programming Errors Error Message Sent to the Sender Error messages that are emailed from the DP-2500/3000 to the original sender during remote programming of the Phone Book via email. Error message 554 Data transfer error (broken header)
APPENDIX Glossary 10Base-T/100Base-TX Client Default Router IP Address Direct Dialing Directory Search Dialing DNS (Domain Name Server) Domain Name Email Address End Receiving Station Ethernet G3 Mode (Group 3) Group Dialing Halftone Header Home Page An Ethernet standard for cable. The 10/100 refers to its 10/100 Mbps bandwidth, the base to single channel baseband, and the T to the Twisted pair.
Page 133
The host is the first (left most) section of the Fully Qualified Domain Name (FQDN). The remainder of the FQDN is the domain and often tells you something about where the DP-2500/3000 is located (i.e., at Panasonic).
Page 134
Connect 2 or more networks together and you have an internet. POP refers to the way email software such as Eudora or the DP-2500/3000 gets email from a mail server. You must always have a POP account that you tell your email software to use to retrieve your mail.
Page 135
Glossary Subnet Mask A mask bit used to manage sub-segments of the network which is defined with network IDs. TCP/IP (Transmission Control TCP/IP is a suite of protocols used to connect to the Internet and wide- Protocol/Internet Protocol) area networks. TIFF Image Viewer An application software to view the contents of TIFF-F File.
Index Communication Journal (Comm. Journal)...121 Control Panel ...10 Customizing Your Machine ...51 Email Address ...27 FAX Parameter List...126 Fax Parameter Table ...53 Function Key ...9 Host Name ...27 Ifax Return Receipt ...96 Important Information ...22 Inbound Routing...90 Information Codes...129 Internet Communication Features...17 Journals and Lists ...117 Mailing List ...71 Multiple Email Station Addressing...
Page 137
Fax Number / Email Address Directory Name Number / Email Address...
Page 138
TO LIABILITY FOR ANY DAMAGE, INCLUDING, BUT NOT LIMITED TO DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS SUSTAINED BY THE CUSTOMER IN CONNECTION WITH THE USE OR APPLICATION OF THIS PANASONIC COPIER. SEE YOUR DEALER FOR DETAILS OF DEALER'S WARRANTY.”...