Related Manuals for ABB ACS580-OP
Summary of Contents for ABB ACS580-OP
- Page 1 — ABB Drive Products ACS580-OP GE Supplemental Manual ACS580-0P GE SUPPLEMENT [3AXD50000875047]...
- Page 2 ACS580-0P GE SUPPLEMENT [3AXD50000875047]...
-
Page 3: Table Of Contents
Table of Contents _____________________________________________________ Safety Instructions ........................4 Introduction to the Supplement ...................10 Mechanical Installation......................12 Electrical Installation ......................14 Operation ..........................16 Maintenance Schedule ......................19 Appendix A ..........................20 Appendix B ..........................22 ACS580-OP GE Supplemental Manual [3AXD50000875047]... -
Page 4: Safety Instructions
Safety Instructions ___________________________________________________________ These are the safety instructions which you must obey when you install and operate the drive and do maintenance on the drive. If you ignore the safety instructions, injury, death or damage can occur. Use of warnings and notes in this manual Warnings tell you about conditions which can cause injury or death, or damage to the equipment. - Page 5 • Beware of hot surfaces. Some parts, such as heatsinks of power semiconductors, remain hot for a while after disconnection of electrical supply. • Keep the drive in its package or protect it otherwise from dust and burrs from drilling and grinding until you install it.
- Page 6 Note: If you select an external source for start command and it is on, and the start command is level-triggered, the drive will start immediately after fault reset. See parameters 20.02 Ext1 start trigger type and 20.07 Ext2 start trigger type in ACS580 control program firmware manual (3AXD50000016097 [English]).
- Page 7 (3AXD50000044794) Quick Start Guide (3AXD50000049129). Additional instructions and note WARNING! Obey these instructions. If you ignore them, injury or death, or damage to the equipment can occur. • If the drive will be connected on an IT system (ungrounded or high-resistance- grounded [over 30 ohms]), make sure neither the EMC filter nor the ground-to- phase varistor are connected (metal screws should not be installed).
- Page 8 • If you are not a qualified electrical professional, do not do grounding work. • Always ground the drive, the motor and adjoining equipment to the protective earth (PE) bus of the power supply. This is necessary for personnel safety. Proper grounding also reduces electromagnetic emission and interference.
- Page 9 ABB and its affiliates are not liable for damages and/or losses related to such security breaches, any unauthorized access, interference, intrusion, leakage and/or theft of data or information.
-
Page 10: Introduction To The Supplement
Introduction to the supplement ___________________________________________________________ Contents of the chapter This chapter describes the supplement. Applicability This supplement is applicable to ACH580-OP drives supplied to General Electric Power with an +A012 in the type code. Target Audience This supplement is intended for people who plan the installation and install the drive. Read the supplement before you work on the drive. - Page 11 You can find manuals and other product documents in PDF format on the Internet. For manuals not available in the Document library, contact your local ABB representative. The code below will open an online listing of the manuals applicable to the product...
-
Page 12: Mechanical Installation
Mechanical Installation ___________________________________________________________ Contents of the chapter This chapter describes the actions needed to assist while installing the drive. Safety WARNING! Lift the drive with a lifting device. Use the lifting eyes of the enclosure. Do not tilt the enclosure. Checking the installation site Check the installation site: ... - Page 13 Leave 12in (305 mm) free space above the basic roof level of the cabinet for cooling and fan replacement. Leave some space at the side to allow doors to open sufficiently (w). The doors can open 120°. ABB recommends minimum of 1” side to side spacing.
-
Page 14: Electrical Installation
Electrical Installation ___________________________________________________________ Contents of the chapter This chapter provides additional information when preparing for the electrical installation. Install Wiring WARNING! Metal shavings or debris in the enclosure can damage electrical equipment and create a hazardous condition. Where parts, such as conduit plates require cutting or drilling, first remove the part. If that is not practical, cover nearby electrical components to protect them from all shavings or debris. - Page 15 Connection diagrams Units are configured for top entry and bottom exit. The following figures show the layout and connection points. Maintain appropriate separation of control and power wires. Wall-Mount Panel Floor-Mount Panel ACS580-0P GE SUPPLEMENT [3AXD50000875047]...
-
Page 16: Operation
This chapter provides additional information in understanding on how to operate the drive. Sequence of operation Refer to the ACS580 Hardware Manual for Operation instructions via the ABB Control Panel. Sequence of operation using the operator devices is contained within this section. - Page 17 Note: Before attempting to run the drive in local, ensure jumpers or additional E-Stop pushbuttons are installed between terminals CTB1:1 & 2, and between CBT1:2 & 3, CTB1:T1 & T2. Ensure all necessary parameters are entered into the drive via the ABB Control Panel or Drive Composer. ...
- Page 18 CTB1:1 & 2, and between CBT1:2 & 3, CTB1:T1 & T2. Ensure all necessary parameters are entered into the drive via the ABB Control Panel or Drive Composer. Before attempting to start the drive, place Hand-Off-Auto Operator(7) in the OFF position, E-Stop pushbutton (8) is released and the speed potentiometer (9) is set to Zero.
-
Page 19: Maintenance Schedule
Maintenance Schedule ___________________________________________________________ Contents of the chapter This chapter provides a recommended maintenance schedule. Maintenance Intervals The lifespan of the cooling fans of the drive depends on the running time, ambient temperature and dust concentration. See the firmware manual for the actual signal which indicates the running time of the Main cooling fans. - Page 20 Appendix A: Ratings ___________________________________________________________ Invertor Frame Size Voltage Ratings Rated Voltage (Un)(VAC) Rated Operational Voltage (Ue)(VAC) Rated Insulation Voltage (Ui)(VAC) Rated Impulse Withstand Voltage (Uimp) 415VAC = 4.0kVAC Current Ratings Rated Current FLA (InA)(A) 33.2 46.6 73.6 88.8 146.6 161.6 366.6 Rated Peak Withstand Current (Ipk)(kA) Rated Conditional Short-Circuit Current (Icc)(kA)
- Page 21 Service Conditions Ambient Air Temperature (°C) 5 … 95% Atmospheric Conditions (Humidity) No condensation allowed. Maximum allowed relative humidity is 60% in the presence of corrosive gases. Storage Temperature (°C) -40 … +70 Operating Temperature (°C) Altitude Derate above 1000m ACS580-0P GE SUPPLEMENT [3AXD50000875047]...
- Page 22 Appendix B: Declaration of Conformity ___________________________________________________________ ACS580-0P GE SUPPLEMENT [3AXD50000875047]...
- Page 23 ABB Inc. 16250 West Glendale Drive New Berlin, WI 53151 Telephone +1 800 752-0696 +1 262 785-0397 Internet www.abb.com/drives ACS580-0P GE SUPPLEMENT [3AXD50000875047]...