Table of Contents
Advertisement
64
LG Network Client Program
•
TLS: Mark up if you want to use the TLS (Transport Layer
Security) function.
-
Mail Address (1 to 3): Enter the mail address.
You can input up to 3 e-mail addresses.
-
Sender : Enter the sender.
NOTE
The SMTP Server, SMTP Port, user name or password settings are
optional. The DVR can send e-mail directly without the use of an
SMTP server or MTA (message transfer agent). In certain cases all
e-mail should be forwarded to a specific SMTP server. Specify the
server host name or IP address in such a case. For more detail on
SMTP setup, ask your network administrator and/or mail service
provider.
3. Click the [OK] button to confirm the settings.
Notification
Mark up when you want to activate the selected option. If the
selected notification option is activate, notify the user about the
information of selected option by E-mail.
•
Sensor On: Sends an e-mail when a sensor has occurred.
•
Motion Detection: Sends an e-mail when an motion detection
has occurred.
•
Text In: Sends an E-mail when the text input is detected.
5
•
Admin PW Changed: Sends an e-mail when the administrator
password has been changed.
•
Video Loss: Sends an e-mail when a video signal from the
camera has stopped because of a cable disconnection or
malfunction of a camera.
•
Power On/Off: Sends an e-mail when power is on or off.
•
Disk Full: Sends an e-mail when the HDD has fully recorded.
Buzzer
Mark up when you want to activate the selected option.
•
Sensor: Makes a sound when a sensor occurs.
•
Motion : Makes a sound when a motion is detected.
•
Text: Makes a sound when the DVR detects text input .
•
System: Makes a sound when a cooling fan is not activated or
the HDD has bad sector.
SNMP
1. Click the [Setup] button.
2. Set the below options.
•
SNMP Version: Selects a SNMP version if SNMP is allowed to
access to this device.
•
Port: Enter the number for SNMP port.
•
Community String (V2 only): Specifies the SNMP management
community in which you want to enable this system (e.g.
lgecommunity or public).
•
User (V3 only): Enter the security name for the SNMP.
•
Authentication (V3 only): Select a mode for the SNMP
Authentication. (MD5 or SHA)
•
Password (V3 only): Enter the password for the SNMP
Authentication.
•
Privacy (V3 only): Select a privacy mode for the SNMP
Authentication. (DES or AES)
•
Password (V3 only): Enter the password for the privacy mode.
•
Trap IP Address: Specifies the IP address of the computer you
intend to use as your network management station and to
which SNMP traps will be sent.
•
Trap Community String (V3 only): Specifies the SNMP trap
community in which you want to enable this system (e.g.
lgecommunity or public).
Emergency
1. Click the [Setup] button.
2. Set the below options.
•
Notification: Mark up to be notified the emergency agent
about the unit's operating information according to your
notification settings.
•
Host Name/Port: Enter the Host Name and port number of
the emergency agent program. The factory default port for
this function is 9002. However in some cases it is better to
change this port number for added flexibility or security.
You can edit this port between 1 025 and 65 535.
You can set up to 9 Host Name and port numbers.
3. Click the [OK] button to confirm the settings.
Output
•
Relay Off
-
Alarm Acknowledged: Use the ALM.OFF button to stop
alarm.
-
Post Alarm Time: The alarm is stopped after post-alarm time.
•
System Alarm Out: Outputs the alarm (relay) signal via the
selected alarm out terminal number when the system has some
problem. If you do not use this function, select [None] option.
•
HDD Fail Alarm Out: Outputs the alarm (relay) signal via the
selected alarm out terminal number when the HDD is failed. If
you do not use this function, select [None] option.
•
Video Loss Alarm Out: Outputs the alarm (relay) signal via the
selected alarm out terminal number when a video signal from
the camera has stopped because of a cable disconnection or
malfunction of a camera. If you do not use this function, select
[None] option.
•
Fan Fail Alarm Out: Outputs the alarm (relay) signal via the
selected alarm out terminal number when the fan is failed. If
you do not use this function, select [None] option.
(This option is not supported for models LRH7160D and
LRH7080D.)
User Settings
Group Authority
You can register a new user group with various access rights.
•
Group ID: Select the group ID to assign authority.
-
Guest: The GUEST group has the limited authority of the
system. Users in this group are available to see the live
image and to set the covert function of the Main or Spot
Advertisement
Table of Contents
