Advertisement
19 Fading hair guard 5/32in.-3/8in.
(4-9mm)
20 Body guard 1/8in. (3mm)
21 Body guard 3/16in. (5mm)
Not shown: cleaning brush, pouch
2
3
4
1
1
2
5
6
7
1
2
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Charging
When the product has charged for 1 hour,
it has a cordless operating time of up to
3 hours.
- Charging, recharging or using the product
at temperatures below 40°F (4,5°C) or
higher than 95°F (35°C) adversely affects
the lifespan of the battery.
2
- If the product is subjected to a major
change in temperature, pressure or
humidity, let the product acclimatize for
30 minutes before use.
1 Make sure the product is switched off.
2 Insert the small plug into the product
and put the power plug in any 120V AC
outlet (Fig. 2).
3 After charging, remove the power plug
from the wall outlet and pull the small
plug out of the product.
Note: An adapter plug may be necessary
for cord usage in some foreign countries.
Use an attachment plug adapter of the
proper configuration for power outlet.
Quick charge
After approx. 5 minutes of charging, the
product contains enough power for one
cordless trimming session.
Using the product
Always check the product and all
accessories before using. Do not use the
product or any accessory if it is damaged,
as this may cause injury. Always replace a
damaged part with one of the original type.
Note: This product can be used without
cord or directly from the power outlet.
Note: Switch off and clean the product
and attachments after each use.
- Use this product for its intended
household use as described in this
manual.
- For hygienic reasons, the product
should only be used by one person.
- Trimming is easier when the skin and
hair are dry.
- Be careful when trimming without a
guard as when the product is turn on it
will trim every hair it touches.
Detaching and attaching cutting
elements
1 To detach a cutting element, push
upwards against the teeth of the cutting
element and take it off the handle (Fig. 3).
2 To attach a cutting element, insert
the lug of the cutting element into the
guiding slot at the front and push the
back of the cutting element onto the
product ('click') (Fig. 4).
Detaching the nose trimmer
1 Place your finger on the arrow at the
back of the attachment and push it off
the handle in the direction of the arrow
(Fig. 5).
Attaching and detaching guards
1 To attach any type of guard onto a
cutting element, slide the front part of
the guard onto the teeth and push the
projection at the back of the guard into
the product ('click') (Fig. 6).
2 To detach any type of guard from the
cutting element, carefully pull its back
part off the product and then slide it off
the cutting element (Fig. 7).
Note: When trimming for the first time,
start by using the guard with the maximum
trimming length setting to familiarize
yourself with the product.
Switching the product on and off
1 Press the on/off button once to turn the
product on or off (Fig. 8).
Attachments for use on beard
Full-size hair trimmer
Use the full-size hair trimmer without a
guard to trim hair close to the skin
(to a length of 1/32in./0.5mm) or to create
clean lines around your beard, neck and
sideburns.
1 To trim hair close to the skin, place the
flat side of the cutting element against
your skin and make strokes against the
direction of hair growth (Fig. 9).
2 For contouring, hold the cutting
element perpendicular to the skin and
move it upwards or downwards with
gentle pressure (Fig. 10).
Beard guards
Attach a beard guard to the full-size hair
trimmer to trim your beard and moustache
evenly. The product comes with 5 beard
guards. The hair length settings are
indicated on the guards. The settings
correspond to the remaining hair length
after trimming.
Guard
inch
mm
Stubble
3/64in.
1mm
guard
Stubble
5/64in.
2mm
guard
Beard guard 1/8in.
3mm
Beard guard 3/16in.
5mm
Beard guard 9/32in.
7mm
1 Attach the guard to the full-size hair
trimmer.
2 To trim the most effective way, move
the guard against the direction of hair
growth (Fig. 11). Make sure the surface
of the guard always stays in contact
with the skin.
Attachments for use on body
- Use the green body guards to trim
body hair.
- When you trim for the first time, use the
5mm/3/16in. body guard to familiarize
yourself with the product.
- Make sure hair is clean and dry as wet
hair tends to stick to the body and,
when trimming sensitive areas, always
use a body guard.
- Since all hairs do not grow in the same
direction, you may want to try different
trimming positions (i.e. upwards,
downwards, or across). Practice is best
for optimum results.
- Always make smooth and gentle
movements and be sure the surface of
the guard always stays in contact with
your skin.
- When too many hairs have accumulated
on the product, blow the hairs out
before use, for best trimming results.
Body guards
Attach a body guard to the full-size hair
trimmer to trim hairs below the neckline.
The product comes with 2 body guards.
The hair length settings are indicated on
the guards. The settings correspond to the
remaining hair length after trimming.
Guard
inch
mm
Body guard
1/8in.
3mm
(green)
Body guard
3/16in.
5mm
(green)
Advertisement
