Pioneer XY-101 Installation Manual

Hide thumbs Also See for XY-101:

Installation manual (77 pages)

Installation manual (80 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

XY-81

8-inch two-way loudspeaker

XY-101

10-inch two-way loudspeaker

XY-122

12-inch two-way ｌoudspeaker

XY-152

15-inch two-way ｌoudspeaker

XY-2

Two-way ｌoudspeaker

XY-3B

Three-way bi-amp loudspeaker

XY-115S

15-inch bass reflex subwoofer

XY-118S

18-inch bass reflex subwoofer

XY-215S

Dual 15-inch quasi-bandpass subwoofer

XY-218S

Dual 18-inch bass reflex subwoofer

XY-218HS

Dual 18-inch horn-loaded subwoofer

Loudspeaker XY Series

Installation manual

http://pioneerproaudio.com/

Version 5.1 June 2018

Table of Contents

Summary of Contents for Pioneer XY-101

Page 1 Three-way bi-amp loudspeaker XY-115S 15-inch bass reflex subwoofer XY-118S 18-inch bass reflex subwoofer XY-215S Version 5.1 June 2018 Dual 15-inch quasi-bandpass subwoofer XY-218S Dual 18-inch bass reflex subwoofer ©2018 Pioneer DJ Corporation XY-218HS Dual 18-inch horn-loaded subwoofer All rights reserved...
Page 2: Table Of Contents
5.1.2 XY-122/152 P.60 5.1.3 XY-2 P.63 5.2 Three-way loudspeaker P.66 5.2.1 XY-3B 5.3 Subwoofer P.71 5.3.1 XY-115S/118S/218S P.74 5.3.2 XY-215S P.76 5.3.3 XY-218HS 6 Specifications 6.1 Spec sheet P.78 6.2 drawing P.82 Page 2 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 3: Introduction
Pioneer DJ shall accept no liability for damage or injury caused by accidents resulting from Pioneer products tipping over or falling due to them being insufficiently secured.
Page 4 Do not use headphones while operating a motorised vehicle; the use of headphones may create a traffic hazard and is illegal in many areas. About trademarks and registered trademarks ・Pioneer is a registered trademark of PIONEER CORPORATION. ・SpeakON is a registered trademark of Neutrik. The names of companies and products mentioned herein are the trademarks of their respective owners.
Page 5: Installation Guidelines
Give sufficient consideration to safety when performing the work. Full-range loudspeakers ・ The XY-81, XY-101, XY-122 and XY-152 come with pre-inserted mounting screws. These screws can be taken out and used to attach either special mounting hardware designed for the product or commercially available mounting hardware.
Page 6 ・ Make sure to install the system in a stable location if using a pole for mounting. ・ Make sure to use mounting hardware of sufficient strength to secure the speaker in place. The speaker could fall, causing accidents, if not properly secured. Page 6 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 7: System Set-Up
Stand mounting ・ The XY-81, XY-101, XY-122 and XY-152 can be mounted on a loudspeaker stand using the equipped polemount adapter for a standard 35 mm (1.4 in.) loudspeaker stand. The XY-2 can be mounted on loudspeaker stand using polemount adapter which fits both for hole of 13mm diameter and for a standard 35 mm (1.4 in.) loudspeaker stand.
Page 8: Accessories
(see Table 2-1 and 2-2 "Accessories List") Please ensure that you read "Section 1: Introduction" and "Section 3.1 - 3.2" fully, and have the product installed by a professional. Have the installer carefully follow the installation instructions. Page 8 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 9 XY-218S XY-218HS 2 x M20 Hardware polemount Speaker Pole polemount polemount standby sockets socket socket (top,right side) Accessories Caster set CP-XYCS1 CP-XYCS1 CP-XYCS1 CP-XYCS1 List Refer to 　Setting procedure Section 3.2.7 Page 9 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 10 Applicable models: XY-81-W : 1 piece of white seal is shipped with XY-81-W. XY-101-W : 1 piece of white seal is shipped with XY-101-W. XY-122-W : 1 piece of white seal is shipped with XY-122-W. XY-152-W : 1 piece of white seal is shipped with XY-152-W.
Page 11 ・When attaching the XY-2 to the XY-3B, do not attach it to anywhere other than the bottom of the XY-3B. ・Do not use the bolt other than special bolt included with XY-2 for mounting to the XY-3B. Page 11 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 12: Rigging And Caster Setting
45 degrees at maximum. Do not suspend the eye bolts as shown in the right figure. (Fig. 3-1-1-B) Fig. 3-1-1-B Page 12 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 13 (1) Make a small slit around the pre-inserted screws using an appropriate cutting knife. (2) Carefully remove the screws using a screwdriver, and ensure the cabinet coating is not peeled off. Page 13 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 14: Horn Rotation
Using a hex key, remove the bolts holding the HF waveguide in place. (Fig.3-1-2-B) Fig.3-1-2-A Fig.3-1-2-A 4 bolts from XY-81/101 and 8 bolts from XY-122/152 are needed to be removed from each enclosure. Fig.3-1-2-B Page 14 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 15 Reinstate the bolts and retighten. Avoid over tightening as this may crack the waveguide. Reinstate the grille by gently placing it in place over the front of the loudspeaker. Reinstate the bolts to secure it in place. Fig.3-1-2-C Page 15 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 16: Logo Badge Replacement
3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.1.3 Logo badge replacement The location of Logo badge attached to the grilles on XY-81/101/122/152 can be changed. Required tools XY-81 / XY-101 XY-122 / XY-152 ・Phillips head screwdriver ・3mm hex key ・Phillips head screwdriver ・4mm hex key...
Page 17 A plate to support the grille DO NOT ATTACH THE LOGO BADGE. GRAY AREA Any part of the LOGO BADGE Bottom should not protrude to the gray area. Factory default Fig.3-1-3-F For vertical installation (XY-81) Page 17 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 18 DO NOT ATTACH THE LOGO BADGE 5 holes 9 holes DO NOT ATTACH THE LOGO BADGE. GRAY AREA Any part of the LOGO BADGE should not protrude to the gray area. Fig.3-1-3-G For horizontal installation (XY-81) Page 18 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 19 A plate to support the DO NOT ATTACH THE LOGO BADGE. GRAY AREA Any part of the LOGO BADGE should not protrude to the gray area. Bottom Fig.3-1-3-H For vertical installation (XY-101) Bottom 7 holes 8 holes DO NOT ATTACH THE LOGO BADGE...
Page 20: Procedures
For all the models, the following situations are quite dangerous. Suspending from sloped Suspending Suspending (non-horizontal) ceiling from the wall multiple enclosures Only for the following model: CP-XY8VC1/XY10VC1/XY15VC1 Inclining over 75 deg (XY-81/101), 45 deg (XY-152) Page 20 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 21: Vertical Flying Cradle
8mm hex socket head Spring Washer 06D015 Flat washer 06D014 M10 socket head bolt 06G053 M10 x 30mm (P=1.5), 8mm hex socket head Load Plate NOTE: XY-122 is shown in the illustrations below. Page 21 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 22 Using the supplied two M8 countersunk bolts(B), align the mounting holes in the inner yoke of the Vertical Flying Cradle(A) with the mounting points on the top of the enclosure. Tighten the bolts over 7N·m torque. Page 22 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 23 Ensure that both the Flat Washer(D) and the Spring Washer(C) Fig.3-2-1-E are used - the Flat Washer(D) should be in contact with the cradle. Tighten the bolts over 15N·m torque (Only XY-101: 7N·m torque). (Fig.3-2-1-C) Once the desired angle of the loudspeaker is set, tighten the knobs/levers on the cradle to lock the position in place.
Page 24: Horizontal Flying Cradle
Also, the location and the orientation of the logo badge can be changed. (See "3.1.2 Horn rotation" and "3.1.3 Logo badge replacement") Page 24 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 25 Mounting Plate Neoprene Washer 05B010 40mm x 2mm Flat Washer 06D014 Spring Washer 06D015 Page 25 / 92 Lever 05A103 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION M10 x 40mm (P=1.5), M10 socket head bolt 06G053 8mm hex socket head Spring Washer 06D015...
Page 26 Horizontal Flying Cradle. Remove the four pre-inserted mounting screws on the top and the bottom of XY-81/101/122/152. (XY-81/101/122: Fig.3-2-2-A), (XY-152: Fig.3-2-2-B) XY-122/101/122 XY-152 Fig.3-2-2-A Fig.3-2-2-B Page 26 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 27 Fig.3-2-2-E Ensure the two commercially-available eyebolts are secured to the rear points on the enclosure to suspend it with wire as a secondary safety feature. (Fig.3-2-2-F) Commercially -available eyebolt Fig.3-2-2-F Page 27 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 28 Once the desired angle of the XY-2 is set, tighten the socket head bolts on the side of yoke to lock the position in place at 15N·m torque. (Fig.3-2-2-I) WARNING: ・Excluding installation, do not loosen the XY-2 side hexagon socket head cap bolts. Page 28 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 29 XY-3B rear, securely fix the eye- bolt on the XY-3B and the hole on the back of XY-2 using secondary safety wire. (Fig.3-2-2-J) Commercialy available eye bolt Safety wire Hole for secondary safety feature. Fig.3-2-2-J Page 29 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 30: Variable Angle Bracket
Table:3-2-3-D：Mounting point of CP-XY3DF1 and inclined angle of the speaker The mounting point Only XY-3B Angle [°] XY-3B + XY-2 Front Back Page 30 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 31 ・Variable Angle Bracket is not supposed to be used in the following situations, which may cause an injury or accident. Suspending from sloped Suspending Suspending (non-horizontal) ceiling from the wall Multiple enclosures Page 31 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 32 10B917S M10 x 20mm (P=1.5), M10 socket head bolt 06B522 8mm hex socket head Included spare: 5 Spring washer 06D015 M10, Included spare: 5 Flat washer 06D014 M10, Included spare: 5 Page 32 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 33 Ensure the commercially-available eyebolt are secured to either right or left mounting point on the top of the enclosure to suspend it with wire as a secondary safety feature. (Fig.3-2-3-E) Fig.3-2-3-E Page 33 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 34 -available feature. (Fig.3-2-3-I) eyebolt For preventing to occur the noise from secondary safety wires, wire length should be as short as possible. Fig.3-2-3-I Page 34 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 35: Dual Enclosure Flying Plate Set(*Dual + Variable)
・Dual Enclosure Flying Plate Set is not supposed to be used in the following situations, which may cause an injury or accident. A° B° ≠ A deg B deg Unsymmetry Suspending from sloped Suspending (non-horizontal) ceiling Over 2 enclosures placement Page 35 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 36 Spring washer(C) and Flat washer(D) are used in between the Dual enclosure flying plate(A) and the M10 socket head bolt(B). Tighten the bolts at 15N·m torque. (Fig.3-2-4-B) Fig.3-2-4-A NOTE: XY-122 is shown in the illustration. Fig.3-2-4-B Page 36 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 37 Note: The angle between the two enclosures can be adjusted as shown in Table.3-2-4-A Remove the two mounting screws pre-inserted in the M10 holes on the Fig.3-2-4-F side of the XY-122/152 enclosure. (Fig.3-2-4-F) Page 37 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 38 ・When assembling cluster using the CP-XY3DF1, the top of each enclosure must be fixed with the proper mounting holes on top plate(A) as following figure. Fig.3-2-4-I Mounting holes on the top plate Page 38 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 39 Fig.3-2-4-J To the ceiling 16 holes on the top plate can be used to install the speaker to the ceiling. (Fig.3-2-4-K) Fig.3-2-4-K Page 39 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 40 NOTE: All the parts for a combination of Dual Enclosure Flying Plate Set and Variable Angle Bracket should be compatible with respective speakers, XY-122 and XY-152. NOTE: XY-122 is shown in the illustration. Page 40 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 41 A deg B deg ≠ A deg B deg Suspending from sloped Suspending Suspending Unsymmetry (non-horizontal) ceiling from the wall Over 2 enclosures placement Page 41 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 42 Variable Angle Bracket to the plate and place the Variable Angle Bracket in the right position to align its front and the ( I ) top front of the plate. Front Back Fig.3-2-4-N Page 42 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 43 Once the desired angles of the two XY-122/152 are set, fully tighten all the M10 socket head bolts to lock the position in place. Note: ・ The angle between the two enclosures can be adjusted shown in Table.3-2-4-A Fig.3-2-4-P Page 43 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 44 Since eyebolts should be mounted to the enclosure as secondary safety feature, the angle between the 2 enclosures should be between minimum degrees and maximum degrees in order to mount the eyebolts. Fig.3-2-4-Q Commercially -available eyebolt Fig.3-2-4-R Page 44 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 45: Suspension Of Enclosure Using The Eye Bolt
*Combi na ti on wi th eyebol t XY-3B *Hori zonta l s us pendi ng i s 60 kg i s not a l l owed not a l l owed Page 45 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 46 Suspended by 1 line of Suspending holes for wall mount brackets wire/chain/tool over 3 enclosures Only for the following model : XY-3B Suspending Horizontal suspending Suspending using XY-2 mounting holes at bottom multiple enclosures Page 46 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 47 Table.3-2-5-A. Note: If the recommended mounting points are used for horizontal suspension of the XY-101/122 enclosure, the enclosure is slightly inclined downward from the beginning. The inclined angle for each speaker are as follows:...
Page 48: Wall Mount Bracket
The holes for commercially-available wall mount brackets are provided on the rear of the XY-81/101/122/152. Note: Pioneer does not sell wall mount brackets. Please ensure that the commercially-available wall mount bracket is compatible with the sizes shown in Table 3-2-6-A Table 3-2-6-A: Size of the hole and the area for a wall mount bracket to be attached.
Page 49: Caster
- the Flat washer(C) should be in contact with the Caster(A). Tighten the bolts at 7N·m torque. (Fig.3-2-7-B) Turn the XY-118S/215S/218HS enclosure with its grille up to roll on the casters. (Fig.3-2-7-C) Fig.3-2-7-A Fig.3-2-7-C Fig.3-2-7-B Page 49 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 50: Wheel Board
・When stacking, apply the locking castor locks firmly. Additionally, after stacking, check that the guide on the underside of the wheel board on the upper enclosure is fit firmly into the enclosure on the underside. Fig.3-2-8-B Page 50 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 51: System Configuration
Impedance 8Ω 8Ω 4Ω 4Ω 4Ω Power 700W 1000W 800W 1600W 1400W Program 1400W 2000W 1600W 3200W 2800W Handling Recommended K3DSP K10DSP K3DSP K10DSP K10DSP Amplifier Minimum K3DSP K2DSP K6DSP K6DSP Page 51 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 52 M30DHDSP 8Ω 900W x 2ch 4Ω 1200W x 2ch M20DHDSP 8Ω 600W x 2ch 4Ω 3000W x 8ch 8Ω 1600W x 8ch X-Series 4Ω 3000W x 4ch 8Ω 1600W x 4ch Page 52 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 53 8 Ω 16 Ω 1.0mm 1.5mm 2.0mm 2.5mm 116m 4.0mm 176m 6.0mm 132m 264m XY-81 / 101 / 122 / 152 XY-2 XY-3B XY-115S / 118S XY-215S / 218S / 218HS Page 53 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 54 OUT1 1+ : Speaker 1+ OUT1 1+ : Speaker 1+ 1- : NC 1- : Speaker 1- OUT2 2+ : NC OUT2 1+ : Speaker 2+ 2- : Speaker 1- 1- : Speaker 2- Page 54 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 55: Drive Unit Replacement
The performance, reliability and safety for use of this product may not be affected even if the above issue occurs. Page 55 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 56: Xy-81/101
・10mm spanner Spring washer M5 x 30mm (P=0.8) 4mm hex socket head M5 socket head bolt 06G001 for HF waveguide M5 for waveguide Flat washer 06D003 Spring washer 06D005 M5 for waveguide Page 56 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 57 HF drive unit. XY-101: Remove the two nuts from the HF drive unit with a 10mm Spanner. Page 57 / 92 http://pioneerproaudio.com/...
Page 58 Install the HF waveguide to the enclosure. Tighten the four socket head bolts on the HF waveguide. Make sure to place the HF waveguide in the same orientation as before replacing the drive unit. Only XY-101 Page 58 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 59 5 Drive unit replacement __________________________________________________________________________________________________________ Replacement of LF drive unit LF driver units installed in XY-81 and XY-101 are different, but almost the same procedures can be used to replace both LF drive units. Remove the socket head bolts from the LF drive unit.
Page 60: Xy-122/152
Remove the grille from the enclosure. Reverse the above steps when placing the grille back to the enclosure. The grille should be placed back in the same orientation before it was removed. Page 60 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 61 Replace the LF drive unit with a new one. Connect the cables to the two terminals. Red Terminal (+) Brown cable Blue cable Brown cable Black Terminal (-) : Blue cable Black terminal Red terminal Page 61 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 62 Ensure that the terminals of the drive unit are placed as shown below. Location of Tighten the bolts to ensure a solid fit to the grille. terminals Additional information (XY-122/152) For the connection information, please refer to following circuit diagram. Page 62 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 63: Xy-2
Lift the heat sink and MF drive unit up and remove the cables from the MF drive unit. Replace the MF drive unit with a new one. Ensure the location of terminals in MF drive unit. Terminals Page 63 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 64 Tighten the three M5 hex button bolts of the rear terminal box. CAUTION: Make sure to prevent to be caught the cable between the rear terminal box and HF flange plate. Page 64 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 65 5 Drive unit replacement ___________________________________________________________________________________________________________ Additional information (XY-2) For the connection information, please refer to following circuit diagram. Page 65 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 66: Xy-3B
Remove the grille from the enclosure. Reverse the above steps when placing the grille back to the enclosure. The grille should be placed back in the same orientation before it was removed. Fig.5-2-1-A Page 66 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 67 Removing and reinstalling the moulded Bi-horn Set. To replace the MF/HF drive unit, you need to remove the moulded Bi-horn from the cabinet. Remove twelve M6 countersunk bolts from the Horn. (Fig.5-2-1-E) Fig.5-2-1-E Page 67 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 68 Black Terminal (-) : Yellow cable Fig.5-2-1-G Replacement of MF drive unit Remove the two waddings from the heat sink. (Fig.5-2-1- Fig.5-2-1-H Remove the eight socket head bolts from the MF chamber. (Fig.5-2-1-I) Fig.5-2-1-I Page 68 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 69 Bi-Horn in the same orientation as before replacing the drive unit. Tighten twelve M6 countersunk bolts of the moulded Bi- Fig.5-2-1-M-1 Horn and two M10 countersunk bolts of the cabinet. Page 69 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 70 5 Drive unit replacement ___________________________________________________________________________________________________________ Additional information (XY-3B) For the connection information, please refer to following circuit diagram. Page 70 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 71: Subwoofer
Required tools Item Part Name Qty Service Part No. Note ・5mm hex key Drive unit PT-XY118SL1 M6 x 40mm (P=1.0), M6 socket head bolt 06G003 5mm hex socket head Spring washer 06D0075 Page 71 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 72 Install the LF drive unit to the enclosure. Red Terminal Black Terminal Tighten the socket head bolts on the LF drive unit. Tighten the screw to ensure a solid fit to the grille. Page 72 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 73 ___________________________________________________________________________________________________________ XY-118S XY-115S Location of Location of terminals terminals XY-218S Location of Location of terminals terminals Additional information (XY-115S/118S/218S) For the connection information, please refer to following circuit diagram. XY-115S/118S XY-218S Page 73 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 74 Reinstall the LF drive unit to the enclosure. Tighten the socket head bolts on the LF drive unit. Tighten the countersunk bolts to ensure a solid fit to the grille. Left drive unit Right drive unit Page 74 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 75 5 Drive unit replacement ___________________________________________________________________________________________________________ Location of terminals Location of terminals (Right drive unit) (Left drive unit) Additional information (XY-215S) For the connection information, please refer to following circuit diagram. Page 75 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 76: Xy-218Hs
Reinstall the LF drive unit to the enclosure. Tighten the socket head bolts on the LF drive unit. Location of terminals Tighten the bolt to ensure a sodoor fit to the door. Front Back Red Terminal Black Terminal Page 76 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 77 5 Drive unit replacement ___________________________________________________________________________________________________________ Additional information (XY-218HS) For the connection information, please refer to following circuit diagram. Page 77 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 78: Specifications
Accessories (-W model only) (-W model only) (-W model only) (-W model only) The specifications and design of this product are subject to change without notice. Page 78 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 79 Impact-resistant, Black semi-matt Finish Black semi-matt textured textured Suggested Power Recommended : X4 Recommended : X4 Amplifier — — Accessories The specifications and design of this product are subject to change without notice. Page 79 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 80 2 x polemount socket cover — Accessories (-W model only) (-W model only) (-W model only) The specifications and design of this product are subject to change without notice. Page 80 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 81 18 mm (0.7 inch) birch plywood Impact-resistant, Black semi-matt Finish textured Suggested Power Recommended : K10DSP Amplifier — Accessories The specifications and design of this product are subject to change without notice. Page 81 / 92 http://pioneerproaudio.com/ ©2018 Pioneer DJ CORPORATION...
Page 86 6 Specifications 6.2 Drawing φ13 4 x φ11 Copyright @ 2018 Pioneer DJ Corporation...
Page 87 6 Specifications 6.2 Drawing NOTE: The nuts of the threaded fixing points on XY-3B are structured so that bolts cannot pass through them. (max threaded length is 15mm.) Copyright @ 2017 Pioneer DJ Corporation...

This manual is also suitable for:

Xy-218hs Xy-81 Xy series Xy-122 Xy-152 Xy-2 ... Show all

Pioneer XY-101 Installation Manual

Quick Links

Related Manuals for Pioneer XY-101

Summary of Contents for Pioneer XY-101

This manual is also suitable for:

Table of Contents