Table of Contents
Advertisement
Cleaning and care
ã=
Risk of burns, risk of electric shock!
from appliance. Always leave appliance to cool down before
cleaning or servicing. Switch off fuse or pull out mains plug.
Caution!
Risk of damage due to ingress of humidity into the electronic
■
circuitry. Never clean operator controls with a wet cloth.
Surface damage due to incorrect cleaning. Clean stainless
■
steel surfaces in the grind direction only. Do not use any
stainless steel cleaners for operator controls.
Surface damage due to strong or abrasive cleaning agents.
■
Never use strong and abrasive cleaning agents.
Cleaning appliance surface
Suitable cleaning agents and care products for your appliance
can be purchased via the Hotline or from the Online Shop (see
front of the instructions for use).
Note: The appliance surface and controls are scratch-sensitive.
Observe the warranty regulations in the enclosed service
booklet and the following cleaning instructions:
Clean the surfaces with a soft, damp cloth, washing-up liquid
■
or a mild window cleaner. Soften dried dirt with a damp cloth.
Do not scratch!
Dry cloths, abrasive sponges, scouring agents, cleaning
■
agents containing sand, soda, acid, chlorine or any other
aggressive substances are not suitable.
Clean the stainless steel surfaces in the direction
■
of the ground surface only.
Do not use stainless steel cleaner or wet cloths
■
for the controls.
Replacing bulbs
ã=
Risk of burns, risk of electric shock!
from defective bulbs. Switch off fuse or pull out mains plug.
Always replace defective bulbs immediately (leave bulbs
to cool down first) to prevent the remaining bulbs from
overloading.
Important! Use only bulb of the same type and same power
(see bulb holder or rating plate inside the appliance) –
to do this remove metal-mesh grease filter.
Replacing halogen bulbs
Note: When inserting halogen bulbs, do not touch the glass
tube. Use a clean cloth to insert the halogen bulbs.
Carefully remove bulb ring using a suitable tool.
1.
Pull out bulb and replace with bulb of the same type.
2.
Insert bulb cover.
3.
Insert mains plug or switch on fuse again.
4.
6
Cleaning metal-mesh grease filters
The inserted metal-mesh grease filters absorb the grease
particles from the kitchen fumes. Clean the metal-mesh grease
filters under normal use (1 to 2 hours daily) approx. every three
months.
Notes
Do not use any aggressive, acidic or alkaline cleaning
■
agents.
When cleaning the metal-mesh grease filters, also clean
■
the holder for the metal-mesh grease filters in the appliance
using a damp cloth.
The metal-mesh grease filters can be cleaned
■
in the dishwasher or by hand.
In the dishwasher:
Note: If the metal-mesh grease filters are cleaned
in the dishwasher, slight discolouration may occur. This has no
effect on the function of the metal-mesh grease filters.
Do not clean heavily soiled metal-mesh grease filters together
■
with utensils.
Place the metal-mesh grease filters loosely
■
in the dishwasher. The metal-mesh greases filter must
not be wedged in.
By hand:
Note: You can use a special grease solvent for stubborn dirt.
It can be ordered via the Online Shop.
Soak the metal-mesh grease filters in a hot soapy solution.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal-mesh grease filters to drain.
■
Replacing filament bulbs
Lift bulb cover slightly and push towards the outside of the
1.
appliance.
Unscrew bulb and replace with bulb of the same type.
2.
Insert bulb cover.
3.
Insert mains plug or switch on fuse again.
4.
LED lights
Defective LED lights may be replaced by the manufacturer, his
customer service or a qualified technician (electrician) only.
ã=
Risk of injury!
due to LED lights of risk group 1. Do not look directly into the
switched on LED lights for longer than 100 seconds.
Advertisement
Table of Contents
