Sealey SA342 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
‰
WARNING! Disconnect from air supply before changing the blade, servicing or performing maintenance.
‰
Maintain the saw in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in suitable clean and tidy work area, free from unrelated materials, Ensure that there is adequate lighting.
9
WARNING! Always wear approved eye or face and hand protection when operating the saw.
‰
Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
Ensure workpiece is secure before operating the saw.
9
Never hold a workpiece by hand. Use a vice or clamps.
9
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 50-90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
NOTE: Prolonged exposure to vibration from this saw poses a health risk. It is the employer's/owner's responsibility to assess
the hazard correctly and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use any power source except an air compressor.
8
DO NOT operate saw near any flammable substance or on any container that has held a flammable substance.
8
DO NOT use the saw for a task it is not designed to perform.
8
DO NOT operate saw if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT carry the saw by the hose, or pull the hose from the air supply.
8
DO NOT operate saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry the saw with your finger on the trigger.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODUCTION
Ideal for a variety of bodyshop applications such as cutting panels, exhaust work, sills and chassis members. Fitted with safety trigger device
to prevent accidental operation. Features adjustable blade guide. Supplied with a starter pack of blades.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA342
Maximum Cutting Capacity: . . . . . .1.5mm (Steel & Aluminium)
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9000spm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4cfm
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Stroke: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mm
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.166m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5m/s²
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88dB(A)
Consumables: SA34/B14 - 14tpi Air Saw Blade (x5), SA34/B24 - 24tpi Air Saw Blade (x5), SA34/B32 - 32tpi Air Saw Blade (x5)
4. AIR SUPPLY
Recommended hook-up procedure is shown below.
4.1. The saw requires an air pressure of between 50-90psi and an air flow of 4cfm.
WARNING! Ensure the air supply is clean and does not exceed 90psi.
‰
Too high an air pressure and/or unclean air will result in excessive wear and may be dangerous, causing damage and/or personal injury.
© Jack Sealey Limited
RECIPROCATING AIR SAW
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
SA342
Wear a mask
SA342 Issue 3 (F,3) 05/08/21