Dip Switch Setting - Mitsubishi Electric PMCR-50VHA-200D KIT Installation Manual

5. Dip switch setting

5.1. Dip switch functions
Located on the FTC2BR printed circuit board are 5 sets of small white switches
known as Dip switches. The Dip switch number is printed on the circuit board next
to the relevant switches. The word ON is printed on the circuit board and on the Dip
switch block itself. To move the switch you will need to use a pin or the corner of a
thin metal ruler or similar.
Dip switch settings are listed below.
Make sure to turn off both indoor unit and outdoor unit power supplies before
changing the switch settings.
Dip switch
SW1 SW1-1 System setting
SW1-2
SW1-3 DHW tank
SW1-4 Immersion heater
SW1-5 Booster heater function
SW1-6 Outdoor unit type
SW1-7 Cooling mode function
SW1-8 Automatic change over mode function
(Heating mode ↔ DHW mode)
SW1-9 Automatic change over mode function
(Cooling mode ↔ DHW mode)
SW1-10 Heat pump maximum outlet water temp.
SW2 SW2-1 DHW temparature drop
SW2-2 Operation in DHW mode
SW2-3 Economy setting for water circulation pump
SW2-4 Legionella prevention mode setting
SW2-5
SW2-6 Legionella prevention hot water temp.
SW2-7 Immersion heater usage in DHW mode
SW2-8 Booster heater usage in Heating mode
SW2-9 Booster heater usage in DHW mode
SW2-10 Heater delay timer in DHW mode
SW3 SW3-1 3-way valve control during defrost in Heating mode OFF (Heating circuit)
SW3-2 Water circulation pump manual operation
SW3-3 3-way valve manual operation
SW3-4 Room thermostat input (Ana,IN1) logic change
SW3-5 Comp. OFF for mode change (DHW ↔ Heating)
SW3-6 Flow switch input (IN3) logic change
SW3-7 Emergency mode
(Heater only operation)
SW3-8 Freeze protection function
SW3-9 Thermo differential during comp. cycling (ON/OFF)
prevention operation
SW3-10
SW4 SW4-1 Pressure sensor
SW4-2 Flow sensor
SW4-3
SW4-4
SW4-5
SW6 SW6-1 Analog input setting
SW6-2
Note: 1. When the FTC2BR is connected with a outdoor unit of which maximum outlet water temperature is 55ºC, Dip SW1-10 must be changed to OFF.
2. If emergency mode is no longer required, return the switch to OFF position.
Function
SW1-1 SW1-2
OFF
ON
OFF
ON
WITH DHW tank
WITHOUT Immersion heater
For Heating and DHW
Split type
Inactive
Active
Active
55°C
10deg
Eco
Inactive
SW2-4
OFF
OFF
60°C
Used
Used
Used
15min
OFF
OFF
Operation stop at thermostat short
Inactive
Failure detection at fl ow switch short
Normal
Active
Target temp. ±3deg
—
WITHOUT Pressure sensor
WITHOUT Flow sensor
—
—
—
SW6-1
OFF
OFF
OFF
ON/OFF input Change mode input Change temp. input
OFF Remote controller Remote controller
OFF External input
Analog input
ON
(4-20mA/1-5V)
ON External input
SW2-5
OFF Activate every "1 times" DHW operations.
ON OFF Activate every "15 times" DHW operations.
ON Activate every "150 times" DHW operations.
ON ON Activate by IN2.
—
—
—
—
SW6-2
OFF 0-10V or Not used
ON OFF
ON 1-5V
ON ON 4-20mA
SW6
SW1,SW2,
SW3,SW4
ON
Remote controller
Remote controller
Analog input
External input
(4-20mA/1-5V)
Analog input
(0-10V)
WITHOUT DHW tank
WITH Immersion heater
For Heating only or WITHOUT Booster heater OFF
Packaged type
Active
Inactive
Inactive
60°C
20deg
Nomal
Active
Operation
65°C
Not used
Not used
Not used
30min
ON (DHW circuit)
ON
ON
Operation stop at thermostat open
Active
Failure detection at fl ow switch open
Emergency mode (Heater only operation)
(To be activated only when powered ON)
Inactive
Target temp. ±5deg
—
WITH Pressure sensor
WITH Flow sensor
—
—
—
Operation
—
Default
setting
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON*1
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF*2
OFF
OFF
OFF
OFF
OFF en
OFF
OFF
OFF
OFF
OFF
EN-17