Related Manuals for DeWalt XR DWDCD991P2
Summary of Contents for DeWalt XR DWDCD991P2
- Page 1 INSTRUCTION MANUAL DCD991 20V Max* Heavy-Duty 1/2" (13 mm) Brushless Cordless Drill/Driver DCD996 20V Max* Heavy-Duty 1/2" (13 mm) Brushless Cordless Drill/Driver/Hammerdrill...
-
Page 2: Definitions: Safety Guidelines
1) WORK AREA SAFETY Definitions: Safety Guidelines a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. The definitions below describe the level of severity for each b) Do not operate power tools in explosive atmospheres, signal word. -
Page 3: Personal Safety
3) PERSONAL SAFETY b) Do not use the power tool if the switch does not turn it a) Stay alert, watch what you are doing and use common on and off. Any power tool that cannot be controlled with the sense when operating a power tool. - Page 4 c) When battery pack is not in use, keep it away from other this tool without holding it with both hands. Operating this metal objects, like paper clips, coins, keys, nails, screws, tool with one hand will result in loss of control. Breaking through or or other small metal objects, that can make a connection encountering hard materials such as re-bar may be hazardous as from one terminal to another.
-
Page 5: Important Safety Instructions For All Battery Packs
• Avoid prolonged contact with dust from power sanding, sfpm ..... surface feet ....safety alert sawing, grinding, drilling, and other construction activities...... per minute ......symbol Wear protective clothing and wash exposed areas with soap SPM ..... strokes per minute ....visible and water. -
Page 6: Specific Safety Instructions For Lithium Ion (Li-Ion)
NOTE: Do not store the battery packs in a tool with the the battery electrolyte is composed of a mixture of liquid organic trigger switch locked on. Never tape the trigger switch in the carbonates and lithium salts. ON position. •... - Page 7 • An extension cord must have adequate wire size (AWG or WARNING: Shock hazard. Do not allow any liquid to get inside the American Wire Gauge) for safety. The smaller the gauge number charger. Electric shock may result. of the wire, the greater the capacity of the cable, that is, 16 gauge CAUTION: Burn hazard.
-
Page 8: Charge Indicators
Indicator Light Operation • Do not disassemble the charger; take it to an authorized service center when service or repair is required. Incorrect DCB101, DCB102, DCB103 reassembly may result in a risk of electric shock, electrocution or fire. • Disconnect the charger from the outlet before attempting PACK CHARGING any cleaning. -
Page 9: Wall Mounting
Wall Mounting delay, suspending charging. The red light flashes long, then short while in the hot/cold delay mode. DCB107, DCB112, DCB113, DCB115, DCB118 Once the battery has reached an optimum temperature, the charger These chargers are designed to be wall mountable or to sit upright on will automatically resume the charging procedure. -
Page 10: Storage Recommendations
COMPONENTS (FIG. 2) d. If charging problems persist, take the tool, battery pack and charger to your local service center. WARNING: Never modify the power tool or any part of it. Damage 5. The battery pack should be recharged when it fails to produce or personal injury could result. -
Page 11: Intended Use
Forward/Reverse Control Button (Fig. 2) INTENDED USE These drills/drivers/hammerdrills are designed for professional drilling, A forward/reverse control button (B) determines the direction of the percussion drilling and screwdriving applications. tool and also serves as a lock-off button. DO NOT use under wet conditions or in presence of flammable liquids To select forward rotation, release the trigger switch and depress the or gases. - Page 12 low (M), medium (N) and spotlight (O) modes can be changed by FIG. 3 FIG. 4 FIG. 5 moving the switch on the foot of the tool. If the trigger switch remains depressed, the worklight will remain on in all modes. When on low (M) and medium (N) settings, the beam will automatically turn off 20 seconds after the trigger switch is released.
-
Page 13: Low Battery Warning
LOW BATTERY WARNING FIG. 7 FIG. 8 FIG. 9 When in spotlight mode and the battery is nearing complete discharge, the spotlight will flash twice and then dim. After two minutes, the battery will be completely discharged and the drill will immediately shut down. -
Page 14: Operation
The belt hook (J) and bit clip (K) can be be attached to either side of FUEL GAUGE BATTERY PACKS (FIG. 11) the tool using only the screw (L) provided, to accommodate left- or Some D WALT battery packs include a fuel gauge which consists of right- handed users. - Page 15 variation based on product components, temperature and end-user 3. Always apply pressure in a straight line with the bit. Use enough application. pressure to keep drill biting, but do not push hard enough to stall the motor or deflect the bit. 4.
-
Page 16: Maintenance
4. When drilling deep holes, if the hammer speed starts to drop off, Recommended accessories for use with your tool are available pull the bit partially out of the hole with tool still running to help at extra cost from your local service center. I clear debris from the hole. - Page 17 WALT BATTERY AND CHARGER SYSTEMS Chargers/Charge Time (Minutes) 120 Volts 12 Volts Battery Output Cat # Voltage DCB606 60/20 DCB404 DCB406 DC9360 DCB361 DC9280 DW0242 DCB200 45/30** DCB201 DCB203 DCB203BT* DCB204 60/40** DCB204BT* DCB205 75/47** DCB207 DC9182 DCB120 DCB127 DCB080 *BT - Bluetooth®...