1 Safety Precautions 1.1. General Guidelines 1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-RADIATION, shock, fire, or other hazards.
1.3. Before Repair and Adjustment 1.3.1. Main Unit (SU-HTB885) Disconnect AC power, discharge AC Capacitors (C5700, C5701, C5702, C5703, C5704 and C5705) through a 10W, 1W resistor to ground. Caution : DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
1.6. Safety Part Information Safety Parts List: There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi- tive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).
2.2. Service caution based on Legal restrictions (Lead Free Solder, (PbF)) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb).
3 Service Navigation 3.1. Service Information This service manual contains technical information which will allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service manual.
4 Specifications Wireless section Wireless module Frequency Range 2.40335 GHz to 2.47735 GHz Amplifier Section No. of channels RMS output power: Dolby Digital Mode 50 W per channel (6 Ω), 1 kHz, Front ch (L, R ch) ® Bluetooth Section 10% THD ®...
6 Service Mode This unit is equipped with features of service mode mode setting for checking the functions & reliability. 6.1. Service Mode Table 1 Item FL display Key operation Mode name Description Example: Service Mode Upon entering into Service Mode Pressing and hold [VOL-] on main unit then press [▼] follow by [▲] using the remote control.
6.2. Service Mode Table 2 Item FL display Key operation Mode name Description Press [VOL+] button 4 times on the Model Name Display the model name Example: remote control. information MODEL: HTB XXX (XXX stand for model number, Eg : 885) Refer to 6.6 for more information The [SVC MODE] display will appear after 3s,...
6.3. Software Version Check Some example of the actual FL display can be found in below table FL Display Position Examples: POS 9 POS 8 POS 7 POS 6 POS 5 POS 4 POS 3 POS 2 POS 1 HTB885 with software version 03 for year 2015 (ROM TYPE A )
6.8. Service Function Error Code FL display will also be able to display the Error Code of the respective model indicated in the table below Error Code Description of error Automatic FL Display Diagnostic Contents Example: Power off the unit during Abnormality in the stabilized Power Supply blinking.
7 Troubleshooting Guide 7.1. Troubleshooting Flowchart Use the flowchart below to verfiy malfunctions of the unit. 1. Turn on the power of main set. 2. Press and hold the power button for 4 seconds then FL display will show RESET for 2 seconds. 3.
7.2. Troubleshooting guide for Wireless Sound skip from front speaker (Bluetooth input) Check the radio wave interference of other wireless equipment (cordless phone, Place subwoofer & other wireless equipment more than 2 meters away from main unit Audio confirmation microwave oven, WiFi, other BT devices). No sound from front speaker (Bluetooth input) VFD display BLUETOOTH READY board (Micon/DSP &...
7.3. Troubleshooting guide for HDMI Module Problems Checking Points Checking components Expected Results 1) No video and audio 1) External Connection checking (Power ON / Standby Pass i) Check whether HDMI Input and Output is reversed. Cable not reverse Through) ii) Check whether HDMI cable properly inserted.
Page 22
3) No audio form TV (Video is present) i) Check TV Speaker selection setting TV Menu (Viera Menu Link for Panasonic TV) Speaker Selection is set to "TV" (Power ON / Standby Pass ii) Check Player Audio output is set to "ON"...
Page 23
Problems Checking Points Checking components Expected Results 1) Signal Line checking 5) No HDAVI Control (CEC) function i) Check CEC Line Q1200 (Pin 2, 4), IC1104 (Pin 15) There is signal present when executing HDAVI control 2) Parts availability and solderbility condition i) Check CEC Line Q1200, R1208, R1209, R1210 No missing and all pins fully soldered.
8 Disassembly and Assembly Instructions Caution Note: • This section describes the disassembly and/or assembly procedures for all major printed circuit boards & main compo- nents for the unit. (You may refer to the section of “Main components and P.C.B Locations” as described in this service manual) •...
8.2. Disassembly flow chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the ser- vicing. To assemble the unit, reverse the steps shown in the chart below. 8.2.1. Main Unit (SU-HTB885) 8.2.2.
8.5. Disassembly of Main Unit (SU-HTB885) 8.5.1. Disassembly of Rear Cabinet Block Step 1 : Remove 18 screws. Step 2 : Remove Rear Cabinet Block. Caution : Do not exert too much force as it may damage the internal wiring.
Page 30
8.5.2. Disassembly of NFC P.C.B. • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Detach 3P wire at connector (CN4000) on NFC P.C.B.. Step 2 : Remove NFC P.C.B.. Caution : During assembly, ensure to push NFC P.C.B. to Front Cabinet Block Wall. 8.5.3.
Page 31
8.5.4. Disassembly of Optical Jack P.C.B. • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Remove 1 screw. Step 2 : Detach 5P wire at connector (CN3001) on Optical Jack P.C.B.. Step 3 : Remove Optical Jack P.C.B.. 8.5.5.
Page 32
8.5.6. Disassembly of Bluetooth Module • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Remove 1 screw. Step 2 : Detach 16P FFC at connector (CN1701) on Bluetooth Module. Step 3 : Remove Bluetooth Module. 8.5.7. Disassembly of Button P.C.B. •...
Page 33
8.5.8. Disassembly of SMPS P.C.B. • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Remove 4 screws. Step 2 : Detach 7P wire at connector (CN1) on SMPS P.C.B.. Step 3 : Remove SMPS P.C.B.. 8.5.9. Disassembly of HDMI P.C.B. •...
Page 35
8.5.10. Disassembly of Main P.C.B. • Refer to “Disassembly of Rear Cabinet Block”. • Refer to (Step 1) - (Step 4) of item 8.5.9. Step 1 : Detach 4P wire at connector (CN5400) on Main P.C.B.. Step 2 : Detach 2P wire at connector (CN5500) on Main P.C.B.. Step 3 : Detach 4P wire at connector (CN5300) on Main P.C.B..
Page 36
8.5.11. Disassembly of Panel P.C.B. • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Slightly lift up SMPS P.C.B. Unit. Step 2 : Lift up Panel P.C.B. Unit.
Page 37
Step 3 : Slightly lift up Main P.C.B. Unit. Step 4 : Detach 15P FFC at connector (CN3300) on Panel P.C.B.. Step 5 : Detach 3P wire at connector (CN3302) on Panel P.C.B.. Step 6 : Detach 3P wire at connector (CN3301) on Panel P.C.B.. Step 7 : Remove 4 screws.
Page 38
8.5.12. Disassembly of Surround Speaker (SP1) • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Remove 3 screws. Step 2 : Detach speaker wire. Step 3 : Release the speaker wire from the slots. Step 4 : Remove Surround Speaker (SP1). 8.5.13.
Page 39
8.5.14. Disassembly of Woofer Speaker (SP3) • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Remove 4 screws. Step 2 : Detach speaker wire. Step 3 : Release the speaker wire from the slots. Step 4 : Remove Woofer Speaker (SP3). 8.5.15.
Page 40
8.5.16. Disassembly of Woofer Speaker (SP5) • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Remove 4 screws. Step 2 : Detach speaker wire. Step 3 : Release the speaker wire from the slot. Step 4 : Remove Woofer Speaker (SP5). 8.5.17.
Page 41
8.5.18. Disassembly of Surround Speaker (SP7) • Refer to “Disassembly of Rear Cabinet Block”. Step 1 : Remove 3 screws. Step 2 : Detach speaker wire. Step 3 : Release the speaker wire from the slots. Step 4 : Remove Surround Speaker (SP7).
8.6. Disassembly of Active Subwoofer (SB-HWA880) 8.6.1. Disassembly of Rear Panel Block Step 3 : Slightly detach Rear Panel Block. Caution : Do not exert too much force as it may damage the internal wiring. Step 1 : Remove 6 screws. Step 4 : Detach 3P Wire at connector (CN1003) on SW SMPS P.C.B..
Page 43
Step 5 : Detach 2P Wire at connector (CN1006) on the SW 8.6.3. Disassembly of SW Power Button SMPS P.C.B.. P.C.B. Step 6 : Remove Rear Panel Block. • Refer to “Disassembly of Rear Panel Block”. Step 1 : Detach 4P Wire at connector (CN1002) on the SW Power Button P.C.B..
Page 44
8.6.4. Disassembly of SW SMPS and SW Step 4 : Remove 5 screws. Step 5 : Detach 4P Wire at connector (CN1002) on the AC Inlet P.C.B. SW SMPS P.C.B.. • Refer to “Disassembly of Rear Panel Block”. Step 6 : Lift up SW SMPS P.C.B. and SW AC Inlet P.C.B.. Step 1 : Remove 1 screw.
Page 45
Step 8 : Upset SW SMPS P.C.B.. 8.6.6. Disassembly of Subwoofer Speaker Step 9 : Push inward to release catch. (SP61) Step 10 : Remove Digital Receiver Module Unit, SW SMPS • Refer to “Disassembly of Bottom Panel Assembly”. P.C.B. & SW AC Inlet P.C.B.. Step 1 : Remove 4 screws.
9 Service Position 9.1. Main Unit (SU-HTB885) Note: For description of the disassembly procedures, see the Section 8.5 9.1.1. Checking SMPS P.C.B. Step 1 : Remove Rear Cabinet Block. Step 2 : Remove SMPS P.C.B.. Step 3 : Place support block at both sides of Front Cabinet Block. Step 4 : Place SMPS P.C.B.
9.2. Active Subwoofer (SB-HWA880) Note: For description of the disassembly procedures, see the Section 8.6 9.2.1. Checking SW SMPS P.C.B. & SW Step 6 : Check SW SMPS P.C.B. & SW AC Inlet P.C.B.accord- ing to the diagram shown. AC Inlet P.C.B. Step 1 : Remove SW Power Button P.C.B..
< PW FL WL 5V > IR BLASTER REMOTE CN6106 CN3001 REMOTE D2230 CIRCUIT < PW 13V > +13V +3.3V Q2230 D2246 D2231 SWITCH V DET NOTE: “ * ” REF IS FOR INDICATION ONLY SC-HTB885EB/EG(SU-HTB885EB/EG) SYSTEM CONTROL BLOCK DIAGRAM...
Page 51
PWM B BST B 43 D5501 VALID C SW /RESET DC DET DC DETECT +20V CIRCUIT Q5802,Q5803 Q5804,Q5805 TO AUDIO & HDMI BLOCK (1/2) NOTE: “ * ” REF IS FOR INDICATION ONLY SC-HTB885EB/EG(SU-HTB885EB/EG) HDMI & AUDIO (2/2) BLOCK DIAGRAM...
10.2. Active Subwoofer (SB-HWA880) 10.2.1. AUDIO & POWER SUPPLY (1/2) BLOCK DIAGRAM : AUDIO OUTPUT SIGNAL LINE SW SMPS P.C.B. IC5799 SWITCHING MODE POWER SUPPLY CONTROL T5751 TRANSFORMER CL 3 D5791 D5798 VCC 4 D5896 SYS5V D5793 IC5899 SHUNT REGULATOR PC5799 DC DET 5V FB 2...
Page 55
10.2.2. AUDIO & POWER SUPPLY (2/2) BLOCK DIAGRAM : AUDIO OUTPUT SIGNAL LINE SW SMPS P.C.B. PCONT 5V SW LED P.C.B. D4001 RED LED CN4000 CN1003 RED LED CN4000 CN1003 GREEN LED GREEN LED IC5200 POWER AMPLIFIER IC3002 DIGITAL RECEIVER MODULE* DUAL OP-AMP 21 IN2-...
11.2. Active Subwoofer (SB-HWA880) SW POWER BUTTON P.C.B. SUBWOOFER CN1004* CN1006 CN1002 CAUTION RISK OF ELECTRIC SHOCK AC VOLTAGE LINE. PLEASE DO NOT TOUCH THIS P.C.B SW SMPS P.C.B. SW LED P.C.B. TL10* CN4000 (RED) (BLK) CN1003 TL20* CN1000 TO DIGITAL RECEIVER MODULE P.C.B.
12 Schematic Diagram 12.1. Schematic Diagram Notes • Voltage and signal line (All schematic diagrams may be modified at any time with : +B Signal Line the development of new technology) Notes: : -B Signal Line Active Subwoofer (SB-HWA880) : HDMI/Optical/Bluetooth Audio Input S1000: I/D SET switch.
12.3. Active Subwoofer (SB-HWA880) 12.3.1. SW POWER BUTTON, SW LED & SW AC INLET CIRCUIT SCHEMATIC DIAGRAM - 5 SW POWER BUTTON CIRCUIT SW AC INLET CIRCUIT : +B SIGNAL LINE K5701* K5702* S1000 CN1004* ID SET IDSET SW SMPS (DAMP) P5701 +5V_GND (RED)
Page 66
12.3.2. SW SMPS (DAMP) CIRCUIT (1/2) SCHEMATIC DIAGRAM - 6 SW SMPS (DAMP) CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE : AUDIO OUTPUT SIGNAL LINE Q2002 B1AAKD000012 R3108 R5769 R3107 6.8K 6.8K 1.2K +16V VOLTAGE REGULATOR R2000 PVCC_+32V C2006 C3105 R2004...
Page 67
12.3.3. SW SMPS (DAMP) CIRCUIT (2/2) SCHEMATIC DIAGRAM - 7 SW SMPS (DAMP) CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE : AUDIO OUTPUT SIGNAL LINE IC5200 C1BA00000497 DIGITAL AMPLIFIER R1015 C5223 R5206 C5208 C5209 C5212 C5220 C5214 0.47 5.6K 220P C5201...
Page 68
12.3.4. SW SMPS (SMPS) CIRCUIT (1/2) SCHEMATIC DIAGRAM - 8 SW SMPS (SMPS) CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE PC5799 K5723...EB/EG B3PBA0000579 K5737...EB/EG FEEDBACK R5894 CL5723 R5890 2.2K R5798 D5798 B0EAMM000057 D5896 C5798 TO SW SMPS (SMPS) B0EAMM000057 50V10 CIRCUIT (2/2)
Page 72
C5761 T3.15A 250V Q5761 Q5851 PC5720 R5761 QR5762 (TO MAIN P.C.B.) 3753AA-1 3753AA-1 CAUTION RISK OF ELECTRIC SHOCK AC VOLTAGE LINE. PLEASE DO NOT TOUCH THIS P.C.B. SC-HTB885EB/EG (SU-HTB885EB/EG) NOTE: " * " REF IS FOR INDICATION ONLY SMPS P.C.B.
Page 74
13.2.2. SW POWER BUTTON, SW AC INLET & SW LED P.C.B. SW LED P.C.B. (REP5036CD) SW POWER BUTTON P.C.B. (REP5036CC) CN1004* CN4000 D4001 (ID SET) 3740AD 3740AD (POWER) S1000 S1001 3740AC 3740AC SW AC INLET P.C.B. (REP5036CA) TL21* AC IN (BLK) 220V-240V 50Hz...
15.3. Cabinet Parts Location-3 (SU-HTB885) 16 16 SU-HTB885EBK SU-HTB885EGK NOTE: " * " PART IS NOT SUPPLIED / REF IS FOR INDICATION ONLY. CABINET DRAWING...
15.5. Packaging (SC-HTB885) ACCESSORIES BAG * POLYFORM CAP REMOTE CONTROL * POLYFORM CAP A1-1 R/C BATTERY COVER SU-HTB885EB/EG A2 x 2 AC CORD (FOR EG ONLY) A2 x 2 AC CORD (FOR EB ONLY) OI BOOK IR BLASTER WALL MOUNT BRACKET...
15.6. Mechanical Replacement Parts List 15.6.1. Main Unit (SU-HTB885) Safety Ref. Part No. Part Name & QTY Remarks Description RMK0865-1 HDMI CHASSIS RXQ2231 FL HOLDER UNIT Safety Ref. Part No. Part Name & QTY Remarks RMQ2311C EPT SEALER Description RMQ2311D EPT SEALER CABINET AND CHAS- RMQ2311E...
Page 86
15.6.3. Packaging & Accessories Safety Ref. Part No. Part Name & QTY Remarks Description (SC-HTB885) RMQ2311-1 EPT SEALER RMQ2325-1 NFC TAPE RMQ2364 DOUBLE FACE TAPE Safety Ref. Part No. Part Name & QTY Remarks (ACOUSTIC ABOSR- Description BER) PACKING MATERIALS RMQ2366 TOUCH SENSOR TAPE RMQ2369...
15.7. Electrical Replacement Parts List 15.7.1. Main Unit (SU-HTB885) Safety Ref. Part No. Part Name & QTY Remarks Description Q3380 B1ABBE000003 TRANSISTOR (E.S.D) Q5720 B1BABG000007 TRANSISTOR (E.S.D) Safety Ref. Part No. Part Name & QTY Remarks Q5760 B1ADCE000012 TRANSISTOR (E.S.D) Description Q5761 B1ABBE000003 TRANSISTOR...
Page 88
Safety Ref. Part No. Part Name & QTY Remarks Safety Ref. Part No. Part Name & QTY Remarks Description Description D0GDR00J0004 0 1/8W CONNECTORS D0GBR00J0004 0 1/10W D0GBR00J0004 0 1/10W K1KA07AA0193 7P CONNECTOR CN3001 K1KA05AA0051 5P CONNECTOR RESISTORS CN3300 K1MN15B00014 15P CONNECTOR CN3301 K1KA03BA0014 3P CONNECTOR R1504...
Page 89
Safety Ref. Part No. Part Name & QTY Remarks Safety Ref. Part No. Part Name & QTY Remarks Description Description R5833 D0GB101JA065 100 1/10W C5761 F1H1H104B047 0.1uF R5838 D0GB220JA065 22 1/10W C5762 F1H1H104B047 0.1uF R5846 D0GB473JA065 47K 1/10W C5800 F1J2E1020002 1000pF 250V R5849 D0GB104JA065 100K...
Page 90
15.7.2. Active Subwoofer Safety Ref. Part No. Part Name & QTY Remarks Description (SB-HWA880) D5852 DA2J10100L DIODE (E.S.D) D5896 B0EAMM000057 DIODE (E.S.D) D5926 B0EAKM000117 DIODE (E.S.D) Safety Ref. Part No. Part Name & QTY Remarks D5928 DA2J10100L DIODE (E.S.D) Description DZ5701 ERZV10V511CS ZNR PRINTED CIRCUITS...
Page 91
Safety Ref. Part No. Part Name & QTY Remarks Safety Ref. Part No. Part Name & QTY Remarks Description Description W1026 D0GFR00J0005 0 1/4W R5795 D0GD474JA052 470K 1/8W W1028 D0GBR00J0004 0 1/8W R5797 D0GB153JA065 15K 1/10W W1030 D0GBR00J0004 0 1/10W R5798 D0GB220JA065 22 1/10W...
Page 92
Safety Ref. Part No. Part Name & QTY Remarks Safety Ref. Part No. Part Name & QTY Remarks Description Description C5210 F1K2A1040007 0.1uF 100V C5818 F1H1H472B047 4700pF C5211 F1J2A221A030 220pF 100V C5819 F1H1H560B052 56pF C5212 F1H1H221A792 220pF C5820 F1H1H560B052 56pF C5213 F1H1H104B047 0.1uF C5851...