Table of Contents
Advertisement
Installing shielding (curtain etc.)
Arc flash, flying spatter, slugs, and
noise generated during welding can
damage your eyes, skin and hearing.
(1)Install a protective curtain around the welding
manipulator site to prevent the arc flash from
entering the eyes of people in the surrounding area.
(2)When welding or monitoring welding, wear safety
glasses with sufficient light blocking structure or
use a protective mask designed for welding
operation.
(3)When
welding
or
protective clothing designed for welding operation,
such as leather gloves, leg cover and leather
apron, and also wear long-sleeve shirts.
(4)Be sure to wear noise-proof protective equipment if
the noise level is high.
(5)The larger the welding current is, or in case of AC
TIG or MIXTIG welding, the larger the AC frequency
is, the larger the arc sound becomes.
Gas cylinder and gas flow regulator
Overturn of gas cylinder and
blowout of gas flow regulator
can cause injury.
(1)The gas cylinder must be handled properly
according to the applicable law and in-house
standards.
(2)Use the gas flow regulator that is supplied or
recom-mended by our company.
(3)Read the instruction manual of the gas regulator
prior to using it, and observe the cautions in the
manual.
(4)Secure the gas cylinder to a dedicated gas cylinder
stand.
(5)Do
not
expose
temperature.
(6)When opening the valve of the gas cylinder, do not
bring your face close to the discharge outlet.
(7)When the gas cylinder is not used, be sure to
install a protective cap.
(8)Do not hang the welding torch on the gas cylinder,
or touch the gas cylinder with the electrode.
(9)Do not attempt to disassemble or repair the gas
regulator. Such works require special knowledge.
Rotating parts
Rotating parts can cause injury.
(1)Keep away from rotating parts such as cooling
fans，and feed roller of the wire feeder, or hand,
finger(s)， hair or part of your clothes may be
caught by the parts resulting in injury.
(2)Keep all covers, panels and cases closed when
using the product.
(3)Maintenance work and repair should be perform
only by educated and/or skilled persons who
thoroughly understand welding machines. While
Warning symbols for safe usage
monitoring
welding
the
gas
cylinder
to
performing maintenance work or repair work, provide
fence or the like around the welding machine so
that unauthorized person can not come close
carelessly.
Welding wire
Welding wire, especially wire tip part
(1)Do not perform inching operation or pull the torch
switch with your eyes, face or body close to the
end of the welding torch - wire extends out
wear
from the end of the welding torch and may
stick into the eye, face or body.
(2)In case of using a torch cable with the resin liner,
straighten the torch cable and reduce the preset
feed amount (current) to a half or less before
applying the wire inching.
(3)Performing wire inching while torch cable has
been bent extremely can cause the wire to pierce
the resin liner and cable. Make sure to replace
any damaged liner or cable with a new one, or
damaged liner/wire can cause gas leak or
dielectric degradation.
. Against insulation deterioration
Insulation deterioration can cause fire
(1)Keep enough distance from welding power source
when performing welding or grinding work so as to
prevent spatters or iron particles from getting
into the power source.
(2)Perform check and maintenance work periodically
so as to prevent insulation deterioration due to
accumulated dust or dirt.
high
(3)When spatters or iron particles get into the welding
power source, turn off the power switches of the
welding power source and power distribution box,
and then blow out.
(4)Make sure to replace any damaged liner or cable
with a new one as use of damaged liner/cable may
cause gas leak or dielectric degradation.
(5)In order to avoid dust and dirt to be collected inside
of the power source, make sure not to leave the
panel and bolts (including eyebolts) open and
removed.
III
can cause injury.
of welding power source.
Advertisement
Table of Contents
