Sealey VS911.V2 Instruction Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: pLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OpERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE pRODUCT CORRECTLY AND WITH CARE FOR THE
pURpOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR pERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. pLEASE KEEp INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. GENERAL SAFETY
 WARNING! Ensure Health & Safety, local
authority, and general workshop practice
regulations are adhered to when using this
equipment.
 Familiarise yourself with the application and
limitations of the panel bag set, as well as
the potential hazards.
 Maintain the set in good condition.
 Replace damaged parts.
Use genuine parts only. Unauthorised parts
may be dangerous and will invalidate the
warranty.
 Maintain correct balance and footing. Ensure
floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons
away from the working area.
 DO NOT put hands/fingers in apertures
created by bags without first inserting a
mechanical chock to prevent accidental
injury.
 DO NOT use the panel bags for purposes
other than those for which they were
designed.
 DO NOT over-inflate.
 DO NOT use on doors fitted with air bags.
 DO NOT use when you are tired, under the
influence of alcohol, drugs or intoxicating
medication.
 Deflate bag prior to storage.
 Clean, dry and store in supplied bag.
2. INTRODUCTION & SpECIFICATIONS
Multi-purpose durable air cushion devices with
rigid edges and fine control air valve. Suitable
for positioning panels, bonnets and boots, prior
to fitment. A 2mm bag thickness and semi-rigid
construction allows bags to be slid between
door frames and weather-stripping for improved
access for emergency vehicle opening tools.
Soft air cushion is gentle on paintwork, frame,
beadings and glass. Supplied in a vinyl pouch.
INSTRUCTION MANUAL FOR:
panel bag Set 3pc
MODEL No:
. . . . . . . . . . . . . . . . . . . . . . . . .
Model
Load Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . 100kg
Bag Dimensions (W x H): . . . . . . . . . . . . Refer to fig.1
Bag 1: . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 x 182mm
Bag 2: . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 x 188mm
Bag 3: . . . . . . . . . . . . . . . . . . . . . . . . . . 160 x 160mm
3. OpERATION
3.1. TO ADJUST bODY pANELS.
3.1.1. Place a panel air bag between the vehicle
body and panel to be fitted (bonnet, boot
etc.) at the point that needs adjusting.
3.1.2. Attach the pump to the bag valve, ensure
the pump valve is closed (fully clock-wise).
3.1.3. Pump air into the bag by squeezing the
bulb on the pump, (taking care not to
over-inflate) moving the panel to the
required position.
3.1.4. If you need to reposition the panel in
more than one place you can disconnect
the pump from the first bag by pushing
the thumb lever on the pump adaptor and
withdrawing it from the bag valve leaving
the bag inflated, in order to insert and
inflate another bag.
Original Language Version
VS911.V2
VS911.V2
VS911.V2
fig.1
Issue: 1 - 22/08/11