Advertisement
• Pressing the [
] key goes back by 1 track from the track
being played.
• While in CD source, press the [1] key briefl y ([1] key for
CD-DA and [FM] key) to jump to No.28.
• While in CD source, press the [2] key briefl y to jump to
No.14.
• While in CD source, press the [3] key briefl y to display CD
mechanism model name and the version in the upper row.
Press the [3] key briefl y again to go back to the normal
screen. (Time code display)
• While in CD source, press the [6] key briefl y ([6] key for
CD-DA, and [AM] key) to jump to No.15. At this time, the
volume value is set to 28 (5V PRE).
(*1) Only in the test mode, [1] key, [2] key, [3] key and [6] key
shall be displayed on the multi-function key.
1. Press the [FNC] key briefly to make the multi-function
display.
2. Rotate the control knob on the right side and use the
[
]/[
] keys to display the target key in the center.
3. Press the [ ] key briefl y to fi nalize the display.
(*2) Perform the same operations as above on the keys, [1],
[2], [3], and [6] on the remote controller.
● AUDIO adjust mode
• Press the [AUD] key briefl y to enter the audio adjustment
mode.
• Press the remote control [∗] key and [AUD] key to enter
the audio adjustment mode.
• Both AUDIO FUNCTION MODE and SETUP MODE
adjustment items are included.
• By pressing [AUD] and [FM] key briefl y, switch the item
to be adjusted in the following order. (Only in forward
rotation)
The default item shall be Fader and the next item shall be
Balance adjustment. (The adjustment afterward is free.)
• Continuous forwarding by remote control is prohibited.
• Fader is adjusted by the VOL knob and [
3 steps: R15↔0↔F15. (Default value: 0)
• Balance is adjusted by the VOL knob and [
in 3 steps: L15↔0↔R15. (Default value: 0)
• Volume Offset (other than the internal AUX) is adjusted by
the VOL knob and [
]/[
value: 0)
• Volume Offset (internal AUX) is adjusted by the VOL knob
and [
]/[
] keys in 3 steps: -8↔0↔+8. (Default value: 0)
• 2Zone ON/OFF is adjusted by the VOL knob and
[
]/[
] keys in 2 steps: OFF↔ON. (Default value: OFF)
TEST MODE
]/[
] keys in
]/[
] keys
] keys in 2 steps: -8↔0. (Default
KDC-W9537U/W9537UY
KDC-X9006U/X991
● MENU
• Press the [FNC] key briefly to make the multi-function
display and press the [ ] key briefl y to enter the MENU.
• Press the remote control [DNPP/SBF] key and the
[DIRECT] key to enter the MENU.
• Continuous forwarding by remote control is prohibited.
• Only in the test mode, make the USB source MENU show
the F/W Version check item and make the F/W Version be
shown as the default items in the test mode.
• The default item of the TUNER source MENU in the test
mode shall be Local Seek ON/OFF switching. (E/E2 type)
● 2ZONE
• If the [AUTO]/[TI] keys is pressed briefl y while in a source
other than STANDBY, 2ZONE is switched between ON/
OFF.
● Backup current measurement
If reset while in Acc OFF (Back Up ON) condition, MUTE
terminal goes off 2 seconds later, rather than 15 seconds.
(During this time, the CD mechanism does not function.)
● OPEL communication items
(OPEL/OEM display supporting model)
During the test mode, OPEL communication line outputs
the following (At every 500msec, the output condition of
the communication line will be switched.)
CE
DATA
CLK
500msec
500msec
500msec
● G sensor display (G-Analyzer supporting model)
Press [ATT] key briefl y in the STANDBY source to change
to the numerical value display that shows the vertical G
and horizontal G conditions.
ACCEL
CORNER
+0.27G
→0.32G
● Special displays while all lights are on
When all lights are on with STANDBY source, if the
following keys are pressed, the following messages are
displayed.
17
Advertisement
