Related Manuals for Toro Super Recycler 21848T
Summary of Contents for Toro Super Recycler 21848T
- Page 1 Form No. 3440-691 Rev B 48cm 60V Super Recycler ® Model No. 21848—Serial No. 400000000 and Up Model No. 21848T—Serial No. 400000000 and Up *3440-691* Register at www.Toro.com. Original Instructions (EN)
- Page 2 This manual uses 2 words to highlight information. additional information, contact an Authorized Service Important calls attention to special mechanical Dealer or Toro Customer Service and have the model information and Note emphasizes general information and serial numbers of your product ready.
-
Page 3: Table Of Contents
Replace any damaged or unreadable labels. Use only the battery pack specified by Toro. Using other accessories and attachments may increase the risk of injury and fire. Plugging the battery charger into an outlet that is not 100 to 240 V can cause a fire or electric shock. - Page 4 Charge the battery pack with only the battery common sense when operating the machine. charger specified by Toro. A charger suitable for Do not use the machine while ill, tired, or under 1 type of battery pack may create a risk of fire the influence of alcohol or drugs.
- Page 5 68°C (154°F) or incinerate the machine. it. Replace the battery pack with a genuine Toro battery pack only; using another type of battery Do not attempt to repair the machine except as pack may cause a fire or explosion.
-
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Model 81860 decal137-9461 137-9461 1. Battery charge status decal137-9489 137-9489 1. - Page 7 decal137-9496 137-9496 1. The battery pack is charging. 3. The battery pack is over or under the appropriate temperature range. 2. The battery pack is fully charged. 4. Battery pack charging fault decal119-2283 119-2283 1. Height of cut decal144-6368 144-6368 1.
-
Page 8: Setup
Setup Note: The battery pack is not fully charged when it is purchased. Before using the machine for the first time, refer to Charging the Battery Pack (page 20). Mounting the Battery Charger (Optional) Parts needed for this procedure: Mounting hardware (not included) Procedure If desired, mount the battery charger securely on a wall using the wall-mount key holes on the back of... -
Page 9: Unfolding The Handle
Tighten the handle knobs firmly by hand. Rotate the handle rearward to the operating position, and lock the handle at your desired height. Refer to Adjusting the Handle Height Unfolding the Handle (page 13). No Parts Required Procedure WARNING Folding or unfolding the handle improperly can damage the cables, causing an unsafe operating condition. -
Page 10: Assembling The Grass Bag
Assembling the Grass Bag No Parts Required Procedure g241560 Figure 6... -
Page 11: Product Overview
Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories. To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. -
Page 12: Before Operation
Operation Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Installing the Battery Pack Important: Use the battery pack only in temperatures that are within the appropriate range; refer Specifications (page 11). Make sure that the vents on the battery are clear of any dust and debris. -
Page 13: Adjusting The Handle Height
Adjusting the Handle Adjusting the Cutting Height Height You may raise or lower the handle to a position WARNING comfortable for you. Adjusting the cutting-height levers could Rotate the handle lock, move the handle to 1 of 3 bring your hands into contact with a moving positions, and lock the handle into position (Figure 10). -
Page 14: During Operation
During Operation Starting the Machine Ensure that the battery pack is installed in the machine; refer to Installing the Battery Pack (page 12). Insert the electric-start button into the electric starter switch (A of Figure 12). Squeeze the blade-control bar and hold it to the handle (B of Figure 12). -
Page 15: Bagging The Clippings
Bagging the Clippings Use the grass bag when you want to collect grass and leaf clippings from the lawn. If the bag-on-demand lever is in the recycling position, move it to the bagging position; refer to Operating the Bag-on-Demand Lever (page 15). -
Page 16: Rear-Discharging The Clippings
Rear-Discharging the Shutting Off the Machine Clippings Release the blade-control bar (A of Figure 18). Remove the electric-start button from the electric Use the rear discharge for cutting very tall grass. starter (B of Figure 18). Note: If the grass bag is on the machine, remove Remove the battery pack;... -
Page 17: Operating Tips
• For best performance, install a new Toro blade before the cutting season begins or when necessary. Cutting Grass •... -
Page 18: After Operation
After Operation Cleaning under the Machine Service Interval: Before each use or daily For best results, clean the machine soon after you have completed mowing. Move the machine onto a flat paved surface. Shut off the motor and wait for all moving parts to stop before leaving the operating position. -
Page 19: Folding The Handle
Folding the Handle WARNING Folding or unfolding the handle improperly can damage the cables, causing an unsafe operating condition. g335780 Figure 22 • Do not damage the cables when folding or 1. Handle knobs unfolding the handle. • If a cable is damaged, contact an To unfold the handle, refer to 2 Unfolding the Authorized Service Dealer. -
Page 20: Charging The Battery Pack
Charging the Battery Pack Green Battery pack is charged Battery pack and/or battery charger is over or under Important: The battery pack is not fully charged the appropriate temperature range when you purchase it. Before using the tool for Battery pack charging fault* the first time, place the battery pack in the charger blinking and charge it until the LED display indicates the... -
Page 21: Maintenance
Maintenance Remove the electric-start button and battery pack from the machine before maintaining or cleaning the machine. Always shut off the machine, wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it. Use only the manufacturer’s recommended replacement parts and accessories. -
Page 22: Adjusting The Self-Propel Drive
Do not attempt to destroy or disassemble the battery pack or remove any of its components. Contact your local municipality or your authorized Toro distributor for more information on how to responsibly recycle the battery. -
Page 23: Troubleshooting
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem Possible Cause Corrective Action The machine does not start. - Page 24 Problem Possible Cause Corrective Action The machine is producing a beeping 1. The battery pack is not charged. 1. Remove the battery pack from the sound. machine and charge it. 2. The machine is in an unsafe position 2. Ensure that the machine is not at an for operation.
- Page 25 Notes:...
- Page 26 Notes:...
- Page 27 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.