Setting The Temperature - Bosch TDS25 Series Operating Instructions Manual

en
18. Soleplate
19. Steam gun
20. Steam release button
21. Steam concentrator
22. Brush extension
23. Diffuser extension
24. Fabric cleanser extension
25. Comb brush extension
26. Funnel
27. Cloth protection sole cover
28. Connection plug
29. Accesories box
30. Slot position for connection
31. Protection cap
Preparations (A)
1. Remove any label or protective covering from the
soleplate.
2. Place the appliance horizontally on a solid, stable
surface. You may remove the iron pad from the
appliance and place the iron on it on another solid,
stable, horizontal surface.
3. Remove the detachable water tank and fill it, making
sure not to pass the level mark.
4. Fit the water tank back onto the steam tank.
5. Unwind the mains cable fully and plug it into an earthed
socket.
6. Set the boiler button (4) and main power button (8)
switches to the "Start/I" position.
7. The "Steam ready" indicator lamp (3) will light up after
several minutes, indicating that the appliance is ready
to use.
The steam generator will take more time to reach
"Steam ready" state only upon the initial heating up,
or after performing the desscaling operation (Calc'n
clean).
When water is already present in the steam generator
during regular use, heat up time to reach the operating
temperature will be faster.
8. This appliance has a builtsin water level sensor. The
red "refill water tank" indicator (10) will light when the
water tank is empty.
Important:
• Normal tap water can be used.
To prolong the optimum steam function, mix tap water
with distilled water 1:1. If the tap water in your district is
very hard, mix tap water with distilled water 1:2.
You can inquire about the water hardness with your
local water supplier.
• The water tank can be filled at any time while using the
appliance.
• To avoid damage and/or contamination of the water
tank and the boiler, do not put perfume, vinegar,
starch, descaling agents, additives or any other type
of chemical product into the water tank.
12
All manuals and user guides at all-guides.com
• The iron is not designed to rest on its heal. Please
• The iron pad can be placed into the specially designed
• During it first use the iron may produce certain vapours
• While the steam release button is pressed, the water tank

Setting the temperature

1. Check the ironing instruction label on the garment to
2. Select the temperature (15)
3. The indicator lamp (16) will remain lit while the iron is
Tips:
• Sort your garments out based on their cleaning
• If you are not sure what the garment is made of then
Controlling the pressure
Your steam station is equipped with a pressure gauge (6)
which shows the pressure it works at every moment.
Dial of the gauge is divided into three areas
1. White area shows low pressure (during first heating or
2 Green area is the one in which the station works nors s
3 Red area shows high pressure and during normal use
Ironing with steam (B)
1. Make sure that there is enough water in the water
2. Turn the temperature selector to the steam position,
Any damage caused by the use of the aforemens s
tioned products, will make the guarantee void.
always position it horizontally on the iron pad (2).
recess on the appliance or somewhere suitable alongs s
side the ironing area.
Never rest the iron on the appliance without the
iron pad!.
and odours, along with white particles on the soleplate,
this is normal and it will stop after a few minutes
may produce a pumping sound, this is normal, indicating
that water is being pumped to the steam tank.
determine the correct ironing temperature.
"•" Synthetics
"••" Silk – Wool
"•••" Cotton – Linen
heating and go out as soon as the iron has reached
the selected temperature.
symbol labels, always starting with clothes that have
to be ironed at the lowest temperatures.
begin ironing at a low temperature and decide on the
correct temperature by ironing a small section not
usually seen when worn
loss of pressure during the ironing. In this case, read
Trouble Shooting section)
mally and pressure should be within it during ironing
should not be reached. In case your steam station
reaches it frequently, it will have to be checked by a
technical service centre
tank
between "••" and "max".