Craftsman 917.20380 Operator's Manual page 10

Hide thumbs Also See for 917.20380:
Table of Contents

Advertisement

KNOW YOUR TRACTOR
READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of vari-
ous controls and ad just ments. Save this manual for future reference.
D
C
B
A
Our tractors conform to the applicable safety standards of the
American National Stan dards Institute.
(A) ATTACHMENT LIFT LEVER - Used to
raise and lower the mower or other attach-
ments mounted to your trac tor.
(B) CLUTCH/BRAKE PEDAL - Used for
declutching and brak ing the tractor and
start ing the engine.
(C) PARKING BRAKE - Locks clutch/brake
pedal into the brake position.
(D) THROTTLE/CHOKE CONTROL - Used
for starting and controlling engine speed.
(E) ATTACHMENT CLUTCH LEVER - Used
to engage the mower blades, or other at tach-
ments mounted to your tractor.
H
E
G
F
J
(F) IGNITION SWITCH - Used for starting
and stopping the engine.
(G) REVERSE OPERATION SYSTEM
(ROS) "ON" POSITION - Allows operation
of mower or other powered attachment while
in reverse.
(H) LIGHT SWITCH - Turns the headlights
on and off.
(J) GEARSHIFT LEVER - Selects the speed
and direction of tractor.
10
REEMPLAZAR LA BATERIA
ADVERTENCIA: No haga cortocircuito con los
terminales de la batería al permitir que una llave
de tuerca o cualquier otro objeto entre en contacto
con ambos terminales a la misma vez. Antes de
ins ta lar la batería remueva las pulseras de metal,
los relojes de pulsera de met al, los anillos, etc.
El terminal positivo tiene que conectarse primero
para evitar las chispas debido a la conexión a
tierra por accidente.
1. Levante el asiento a la posición elevada.
2. Remueve la protección de los terminales.
3. Desconecte el cable de la batería NEGRO
primero y luego el cable de la batería ROJO
y remueva la batería del tractor.
4. Instale la nueva batería con los términos en
misma posición como la batería vieja.
5. Reemplazamos cubierta terminal.
6. Primero, conecte el cable de la batería ROJO
con el terminal positivo (+) con el perno
hexagonal y la tuerca según se muestra.
Apriételos en forma segura.
7. Conecte el cable de conexión a tierra NE-
GRO al terminal negativo (-) con el perno
hexagonal y la tuerca que queden. Apriételos
en forma segura.
8. Cerramos la asiento.
Base
Del Asiento
Cubierta
Tuerca
Terminal
Perno
Ca ble Negro
(negativo)
Cable
Rojo
(positivo)
02603
PARA CAMBIAR LA BOMBILLA DE LA LUZ
DELANTERA
1. Levante el capó.
2. Tire el sujetador de la bombilla fuera del
agujero en la parte trasera del enrejado.
3. Cambie la bombilla en el sujetador y empuje
el sujetador de la bombilla, en forma segura,
hacia atrás en el agujero en la parte trasera
del enrejado.
4. Cierre el capó.
ENTRECIERRE Y RELÉS
El alambrado suelto o dañado puede producir el
mal fun cio na mien to de su tractor, o que deje de
funcionar, o le impida el arrancar.
• Revise el alambrado.
PARA CAMBIAR EL FUSIBLE
Cámbielo por un fusible tipo enchufable de 30
amps, tipo au to mo triz. El sujetador del fusible
está ubicado detrás del tablero.
PARA REMOVER EL CONJUNTO DEL
CAPOTA Y DEL ENREJADO
1. Levante el Capota.
2. Desabroche el conector del alambre de las
luces delanteras.
3. Retire la presilla y arandela del pasador pivote
del lado derecho.
4. Sitúese frente al tractor. Tome la capota por
los lados y deslícela hacia la izquierda, para
retirarla de los tornillos de apoyo, y elévela
para extraerla del tractor.
5. Al volver a colocar la capota, enchufe otra
vez el conector del cable del faro y reinstale
la arandela y la presilla en pasador pivote de
apoyo derecho.
Capota
Clavija de pivote
Arandela
Presilla
04031
Clavija de pivote
Conector del Alambre de
Las Luces Delanteras
MOTOR
PARA AJUSTAR EL CABLE DE CONTROL DE
LA ACELERACIÓN
El control de la aceleración ha sido preajustado
en la fábrica y no debería necesitar ajustes. Re-
vise los ajustes que se describen a continuación,
antes de soltar el cable. Si el ajuste es necesario,
vea de manual de motor.
PARA AJUSTAR EL CONTROL DE
ESTRANGULA CIÓN
El control de la estrangulación ha sido preajusta-
do en la fábrica y no debería necesitar ajustes.
55

Advertisement

Table of Contents
loading

Table of Contents