Sealey TC900.V2 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear Protective
instruction Gloves
manual
1. saFetY
ensure the bead seating tool is in good order and condition before use.
9
Before carrying out maintenance on the unit ensure that the pressure has been vented.
9
use only authorised attachments and parts. unauthorised items may be dangerous and will invalidate your warranty.
9
read the instructions regarding any accessory used with the bead seater.
9
Keep the work area clean and tidy.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip safety shoes.
9
ensure the working area is well lit.
9
Always wear safety glasses and ear defenders when using the bead seater.
9
Keep children and unauthorised persons away from the working area.
9
do not use the bead seater to perform a task for which it is not designed.
8
do not deface, or remove, the certification plate attached to the bead seater.
8
▲ dangeR! do not direct compressed air towards people or animals.
WaRning! the bead seater is a pressure vessel and the following safety measures apply.
‰
do not use the bead seater without the safety valve fitted.
8
do not tamper with the safety valve, do not modify or alter the bead seater in any way and do not strap anything to it.
8
do not subject the bead seater to impact, vibration or heat and do not allow contact with abrasives or corrosives.
8
drain condensation from bead seater daily, inspect inside walls for corrosion every three months and have a detailed internal and external
9
inspection carried out annually. the bead seater shell must not fall below the certified thickness at any point.
WaRning! the warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur.
it must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
2. intRoduCtion
the easy and instant way to seat tubeless tyre beads. dumps air into tyre void forcing bead to seat against rim for inflation. Air release is controlled
by a hand lever operating a ball valve. fully certified tank with gauge and safety valve prevents over pressurising. suitable for use on cars,
commercials, agricultural and AtV tyres.
3. speCiFiCation
model no: .............................................................. tc900.V2
maximum Pressure ...................................... 150psi(10.4 bar)
tank capacity ................................................................. 19ltr
Weight ......................................................................... 12.6kg
4. asseMblY
Check that all components are present and in good order. Screw the Barrel firmly
into the Air release Valve using Ptfe tape or equivalent to enable sealing
and ease of removal.
5. opeRation
5.1. to CHaRge tHe tanK.
5.1.1. Attach an air line to the air inlet connection on the bead seater, open the inlet valve and charge the tank to required pressure. the
normal working pressure varies from 50psi to 130psi, depending on the size and condition of the tyre. the bead seater can help inflate
all passenger, truck and even some small agricultural tyres. When used with the wheel in the upright position it will normally require a
pressure over 90psi to set the bead.
© Jack sealey limited
instructions for
bead seating tool
model no:
Wear eye Wear ear Wear Protective
Protection Protection
Original Language Version
tC900.V2
clothing
tc900.V2 issue 1 22/01/18