Sealey BAZOOKA TC903 Instructions

Thank you for purchasing a Sealey product . Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance .
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY . NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS . USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED . FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY . KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE .
Read manual Wear eye
protection
1 . SAFETY
WARNING! Always wear eye and ear protection
p
For indoor use only .
3
Ensure the receiver is in good order and condition before use .
3
Keep the receiver away from heat sources, corrosives and inflammable materials .
3
WARNING! DO NOT tamper with, or attempt to adjust, the safety valve .
p
Before working on the receiver ensure that the pressure has been vented .
3
Use only authorised attachments and parts . Unauthorised items may be dangerous and will invalidate your warranty .
3
Read the instructions regarding any accessory used with the receiver . Ensure the safe working pressure of the receiver exceeds the
3
supply pressure .
Ensure air hoses are not tangled, twisted or pinched .
3
Keep children and unauthorised persons away from the working area .
3
DO NOT use the receiver to perform a task for which it is not designed .
7
DO NOT deface, or remove, the certification plate attached to the receiver .
7
DO NOT operate the bead seating tool whilst tired, ill, under the influence of alcohol or other intoxicating drugs .
7
DANGER! DO NOT direct compressed air towards people or animals .
p
WARNING! The receiver is a pressure vessel and the following safety measures apply:
p
DO NOT use the receiver without the safety valve fitted .
7
DO NOT tamper with the safety valve, DO NOT modify or alter the receiver in any way .
7
DO NOT subject the receiver to impact, vibration or heat and DO NOT allow contact with abrasives or corrosives .
7
Drain condensation from receiver daily when in use, inspect inside walls for corrosion every three months and have a
3
detailed inspection carried out annually . The receiver shell must not fall below the certified thickness at any point .
Clean with a cloth after use and store indoors with the compressed air vented . Also vent before removing barrel or disposal .
3
2 . INTRODUCTION
The next generation of bead blaster which produces a huge punch despite its size . Delivers an instantaneous blast of air . Dumps air into tyre
void forcing bead to seat against rim for inflation. Fully certified tank with gauge, safety valve that prevents over pressurising. Push button trigger
that allows the technician to keep both hands on the tank for more control . Suitable for use on cars, light commercials and ATV tyres . Supplied
with safety spectacles, ear plugs and wall mounting bracket .
3 . SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . TC903
Maximum Pressure: . . . . . . 150psi/10bar
Tank Capacity: . . . . . . . . . . . . . . . . . . 6ltr
Weight: . . . . . . . . . . . . . . . . . . . . . 5 .6kg
4 . CONTENTS
Item No Description
1 Receiver
2 Barrel
3 Pressure Gauge
4 Safety Relief Valve
5 Wall Mounting Bracket
6 Safety Spectacles
7 Ear Plugs
5 . ASSEMBLY
5 .1 . Fit an air coupler nipple, not supplied, to suit the available air line system into the small intake valve shown in fig .1 .
5 .2 . Fit the twin outlet barrel to the receiver securely, ensuring air tight integrity of the connection . In use, it is required that the angle
flange is carrying handle side (opposite side to air release trigger) of the receiver when the task wheel is horizontal (fig .2) .
When the task wheel is vertical the angle flange should be the same side as the air release trigger (fig .3) .
5 .3 . Check the integrity of the pressure gauge and safety relief valve connections .
© Jack Sealey Limited
INSTRUCTIONS FOR:
BAZOOKA BEAD SEATING TOOL 6LTR
MODEL NO:
Wear ear Wear protective
protection gloves
Qty
1
1
1
1
1
1-pair
1-set
Original Language Version
R
TC903
fig.1
(shown in horizontal wheel set up)
TC903 Issue: 1 - 29/01/15