Advertisement
Quick Links
INSTRUCTION
MANUAL
Optical Touch Switch
SW-200 Series
Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thoroughly for
the correct and optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
WARNING
● Never use this product as a sensing device for personnel protection.
● In case of using sensing devices for personnel protection, use
products which meet standards, such as OSHA, ANSI or IEC etc.,
for personnel protection applicable in each region or country.
1
CAUTIONS
This product has been developed/produced for industrial use only.
Make sure to carry out wiring in the power supply off condition.
Take care that wrong wiring will damage the sensor.
Verify that the supply voltage variation is within the rating.
If power is supplied from a commercial switching regulator, ensure that
the frame ground (F.G.) terminal of the equipment is connected to an
actual ground. F. G.
In case noise generating equipment (switching regulator, inverter
motor, etc.) is used in the vicinity of this product, connect the frame
ground (F.G.) terminal of the equipment to an actual ground.
Do not run the wires together with high-voltage lines or power lines
or put them in the same raceway. This can cause malfunction due
to induction.
Do not use during the initial transient time (150ms) after the power
supply is switched on.
Take care that the sensor is not directly exposed to fluorescent
light from a rapid-starter lamp or a high-frequency light device or
sunlight etc., as it may affect the sensing performance.
Extension up to total 100m is possible with 0.3mm
, or more, cable.
2
Make sure that the stress by forcible bend or pulling is not applied
directly to the sensor cable joint.
This sensor is suitable for indoor use only.
Do not use this product in places having excessive vapor, dust,
dirt, etc. or where it may come in direct contact with water, or
corrosive gas.
Take care that the product does not come in contact with water, oil,
grease, or organic solvents, such as thinner, etc.
When the match cable is connected with the sensor, the tightening
torque should be 0.5N·m or less.
2
OPERATION INDICATOR
Operation indicator (orange)
● The orange LED lights up when
output is ON
● The orange LED flashes when
there are objects being detected
for a long time
Power indicator
(green)
3
MOUNTING AND NAMES OF COMPONENTS
Protection cover
(accessory)
Enclosure
Base
M30 male thread and
NPSM1/2" female thread
Rubber gasket
(accessory)
Lock washer
(accessory)
Mounting nut
(accessory)
Positioning washer
(accessory)
(Note):
● The positioning washer and lock washer can be used interchangeably
● The tightening torque should be 180N·m or less
● When the positioning washer is not used, the diameter of the
mounting hole is φ30.5
+0.5
mm
0
● When the positioning washer is used, the dimension of the process hole for
the mounting plate (more than 2mm thick) is shown as below (unit: mm)
5
+0.2
0
30.5
+0.5
0
4
I/O CIRCUIT DIAGRAM
Common anode circuit diagram
Color code
[Brown] +V
Load
[Black] OUT1
10V to 30V DC
Z
D
±10%
Z
D
100mA max.
[White] OUT2
[Blue] 0V
[Pink] A/B switching
External input circuit
External input
Internal circuit
User' circuit
Z
: Surge absorption zener diode
D
(Note): The pink line hanging in the air indicates model A, the pink line connecting with 0V indicates model B.
Common cathode circuit diagram
Color code
[Brown] +V
[Black] OUT1
10V to 30V DC
Z
D
±10%
Z
D
100mA max.
[White] OUT2
Load
[Blue] 0V
[Pink] A/B switching
External input circuit
External input
Internal circuit
User' circuit
Z
: Surge absorption zener diode
D
(Note): The pink line hanging in the air indicates model A, the pink line connecting with 0V indicates model B.
5
SPECIFICATIONS
Model
Supply voltage
Current consumption
Semiconductor photo-MOS output
Output
●Maximum load current: 100mA or less
●Applied voltage: 30V DC or less
●Residual voltage: 1.5V or less (at 100mA load current)
Output operation
Short-circuit protection
Response time
100ms or less when an object is detected, 50ms or less when an object is not detected
Operation indicator
1. Orange LED (lights up when the output is ON) 2. Orange LED flashes abnormally (when there are objects being detected for a long time)
Power indicator
Protection
Ambient temperature
-25°C to +55°C (no dew condensation or icing allowed), Storage: -30°C to +70°C
Ambient humidity
Incandescent light: 3,000 x at the light-receiving face
Ambient illuminance
Voltage withstandability
1,000V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
20MΩ, or more, with 500V DC megger between all supply terminals connected together and enclosure
Vibration resistance
10Hz to 500Hz frequency, 3mm double amplitude (MAX.20G) in X, Y and Z directions for 2 hours each (deenergized)
Shock resistance
500m/s
acceleration (50G approx.) in X, Y and Z directions for three times each (deenergized)
2
Infrared LED (modulated)
Emitting element
Material
Enclosure: PC
Cable
Cable extension
Extension up to total 100m is possible with 0.3mm
Weight
Accessories
rubber gasket: 1pcs, positioning washer: 1pcs, lock washer: 1pcs, mounting nut: 1pcs, protection cover: 1pcs
OPERATION DESCRIPTION
6
t<3 min
Mode A
Light On
Dark On
ON
Output operation
OFF
Lights on
Operation indicator
Lights off
(orange LED)
Mode
Status
Output operation Operation indicator
Light On
Always ON
ON
Dark On (t<3 min)
OFF
Lights off
Mode A
Dark On (t≥3 min)
ON
Flashes
Return to Light On
ON
Always ON
t<3 min
Mode B
Light On
Dark On
ON
Output operation
OFF
Operation indicator
Lights on
(orange LED)
Lights off
Mode
Status
Output operation Operation indicator
Light On
OFF
Lights off
Dark On (t<3 min)
ON
Always ON
Mode B
OFF
Dark On (t≥3 min)
Flashes
Return to Light On
OFF
Lights off
SW-211
10V to 30V DC ± 10% / Ripple (P-P) 10% or less
40mA or less
Switchable either Light-ON or Dark-ON
Incorporated (Automatic reset)
Green LED (lights up when the power is ON)
IP65(IEC)
35%RH to 85%RH, Storage: 35%RH to 85%RH
Sunlight: 120,000 x at the light-receiving face
Emission wavelength: 950nm
Protection Cover: nylon (PA66)
Base: PBT
0.2mm
2
, 5-core cabtyre cable, standard length: 2m
, or more, cable
2
Net weight: 200g approx. Gross weight: 250g approx.
7
INTENDED PRODUCTS FOR CE MARKING
t≥3 min
5
The models listed under "
SPECIFICATIONS "
come with CE Marking.
As for all other models, please contact our office.
Economic operators' information in EU is as follows:
<Manufacturer>
97, Huoju Road, Suzhou New District, Jiangsu, China
+86-512-6843-2580
<Importer>
Panasonic Electric Works Europe AG
Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany
<Contact for CE>
Panasonic Marketing Europe GmbH Panasonic Testing Center
t≥3 min
Winsbergring 15 , 22525 Hamburg , Germany
Above information is applied only when Panasonic Industrial
Devices SUNX Suzhou Co., Ltd. exports this product to EU.
http://device.panasonic.cn/ac/c
97, Huoju Road, Suzhou New District, Jiangsu, China
Phone: +86-512-6843-2580
About our sale network, please visit our website.
© Panasonic Industrial Devices SUNX Suzhou Co., Ltd. 2016
PRINTED IN CHINA
Advertisement
