Husqvarna HG 125 B Original Instructions Manual page 26

Rotating the machine head
Remove the battery from the power
u
tool before carrying out work on the
power tool (e.g. maintenance, chan-
ging tool, etc.). The battery should
also be removed for transport and stor-
age. There is risk of injury from unintentionally
pressing the on/off switch.
the four screws. Rotate the machine head care-
fully, without removing it from the hous-
ing, into the new position. Screw in and retighten
the four screws.
Dust/Chip Extraction
Dust from materials such as lead-containing coat-
ings, some wood types, minerals and metal can be
harmful to one's health. Touching or breathing-in
the dust can cause allergic reactions and/or lead
to respiratory infections of the user or bystanders.
Certain dust, such as oak or beech dust, is con-
sidered carcinogenic, especially in connection with
wood-treatment additives (chromate, wood preser-
vative). Materials containing asbestos may only be
worked by specialists.
– Provide for good ventilation of the working
place.
– It is recommended to wear a P2 filter-class res-
pirator.
Observe the relevant regulations in your country
for the materials to be worked.
Avoid dust accumulation at the work-
u
place. Dust can easily ignite.
Operation
English
Start-up
English
Inserting the battery
Push the charged battery (5) into the base of the
power tool from the front until the battery is se-
curely locked.
Switching on/off
English
To start the power tool, push the on/off switch (4)
forward.
26 | English
English
The machine head can
be rotated in 90° incre-
ments. In this way, the
on/off switch can be
brought into a more fa-
vourable handling posi-
tion for particular ap-
plications, e.g. for left-
handed tool users.
Completely unscrew
English
English
To lock the on/off switch (4) in position, push the
on/off switch (4) forward and down until it clicks
into place.
To switch off the power tool, release the on/off
switch (4); or, if the switch is locked, briefly push
the on/off switch (4) backward and down and then
release it.
Always check abrasive tools before us-
u
ing them. The abrasive tool must be
fitted properly and be able to move
freely. Carry out a test run for at least
one minute with no load. Do not use
abrasive tools that are damaged, run
untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injur-
ies.
Kickback stop
English
If there is a sudden kickback in the power tool, e.g.
jamming in a separating cut, the power supply to
the motor will be interrupted electronically.
To restart the tool, set the On/Off switch (4) to
the "off" position and then switch the power tool on
again.
Restart protection
English
The restart protection feature prevents the power
tool from uncontrolled starting after the power sup-
ply to it has been interrupted.
To restart the tool, set the on/off switch (4) to the
off position and then switch the power tool on
again.
Impact shutdown
English
The integrated impact shutdown switches the
power tool off as soon as it hits the floor. To re-
start the tool, set the On/Off switch (4) to the "off"
position and then switch the power tool on again.
Practical advice
English
Exercise caution when cutting slots in
u
structural walls; see the "Information
on structural design" section.
Clamp the workpiece if it is not secure
u
under its own weight.
Do not load the power tool so heavily
u
that it comes to a stop.
If the power tool has been subjected
u
to a heavy load, continue to run it at
no-load for several minutes to cool
down the accessory.
Do not use the power tool with a cut-
u
off stand.
Do not touch grinding and cutting
u
discs until they have cooled down. The
discs can become very hot while working.
If the power tool becomes electrostatically
charged, the built-in electronics will switch the
1 609 92A 6WV • 26.8.22