Advertisement
What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult
the table below to see if the problem can be corrected before seeking help from your dealer or service representative.
Power ON, but no sound.
@ Poor connection of the power cord plug.
@ Connect the power cord plug securely.
@ The power cord piug is connected
to the | @ Turn ON the power switch of the amplifier.
SWITCHED outlet of the amplifier.
The sound
applied to LINE IN jacks
@ The input selector switch is pressed at TAPE. | @ Press the input selector switch to LINE.
cannot be heard.
@ The input and output connections are re- | @ Connect the input and output correctly,
versed.
No equalizer effect.
@® The TAPE MONITOR switch of the amplifieror | @ Set TAPE MONITOR switch correctly.
receiver is not set to MONITOR.
The equalizer effect is not enough.
@ The EQ. RANGE selector is set to +6 dB.
e
| @Setthe selectorto+12dB,
the selector to £12 dB.
Notes:
1. This system is microprocessor-controlled, so malfunction may occur due to external noise or interference noise. In such a case, unplug the
power cord, plug it and turn power on again.
2. Do not use contact cleaners because it could cause a malfunction. Be specially careful against contact cleaners containing oil, for they may
deform the plastic components.
Specifications
Equalizer characteristics
General
Variable range
..............
deans
Ce 12 OB/26cdE
POWer CONSUMPTION
..................cccceeccceseesecertertneenaaner 20 W
AL & R independently adjustable)
AC outlets
Center frequencies
......................- 60 Hz, 150 Hz, 400 Hz,
For the U.S.A. and Canada
1 kHz, 2.4 kHz, 6 kHz, 15 kHz
UNSWITCHED ....00.
ees
1 (200 W, 1.6 A max.)
Frequency response ...... 10 Hz — 50 kHz, +0 dB, —1.5 dB
For other countries
Total harmonic distortion .................. Less than 0.006%
UNSWITCHED
ooo.
cece eceesseeees 1 (200 W max.)
(fkHz, all controls flat output 1V)
Dimensions
000.........00000 cece
W: 440 mm (17-5/168")
CCE. || 9 | Rane ee eae
en
nee
ve ae
RPE Po
aE
oa
0 +2.7 dB
H: 97 mm (3-13/16")
Maximum output voltage
. . . .
5.4 V (1 kHz, T.H.D. 0.03%)
D: 277 mm (10-7/8")
S/N ratio oo.....:ccccscccss
es eeeeseseseee. 100 dB eee A network, 1V)
Weight (net) ............ccccccccscccssecsessssssssssceseneess 3.5 kg (7.7 Ib)
Input Impedance ........... cee
ee
eee renee
. 50 kQ
Output Impedance
.............ccccccecceeeceeeeeeecceeeeeerewerewenees 2kQ
Note:
For the U.S.A.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The use could lose the authority to operate this equipment if an unauthorized
change or modification is made. ~
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful
interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on 4 circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
For CANADA
DOC REGULATION
"This digital apparatus does not exceed the CLASS B limits for radio noise emissions from digital apparatus as set out In the radio interference
regulations of the Canadian Department of Communications."
12 GE-4020 (En)
Advertisement
