Advertisement
Available languages
Available languages
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
DAILY MAINTENANCE CHART
ACTION
Clean magazine, pusher, and contact
trip mechanism.
WHY
Permits smooth operation of magazine, reduces
wear, and prevents jams.
HOW
Blowing off the tool with compressed air is the
most effective way to clean the tool. The use
of oils, lubricants periodically or solvents is not
recommended as they tend to attract debris
and/or damage the plastic parts of the tool.
ACTION
Before each use, check to ensure all screws and
fasteners are tight and undamaged.
WHY
Prevents jams and premature failure of tool parts.
HOW
Tighten loose screws using the appropriate hex
wrench or screwdriver.
Lubrication
NOTICE: NEVER spray or in
any other way apply lubricants
or cleaning solvents inside the
tool. This can seriously affect
the life and performance of
the tool.
D
WALT tools are properly lubricated at the factory and are
e
ready for use. However, it is recommended that, once a year,
you take or send the tool to a certified service centre for a
thorough cleaning and inspection.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
E
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
WALT recommended
E
Consult your dealer for further information on the
appropriate accessories.
Driver Blade Replacement Kit
(Fig. M–O)
WARNING: For your own safety, read the tool instruction
manual before using any accessory. Failure to heed
these warnings may result in serious personal injury and
damage to the tool and the accessory. When servicing this
tool, use only identical replacement parts.
NOTICE: All the mechanical parts of the driver replacment
kit are shown for convenience and verification of inclusion.
To Change a Worn Driver Blade:
1. Using a T-20 Torx, loosen the four screws
of the unit.
2. Remove the four screws. Refer to Figure M.
3. Remove housing end cap
4. Push up on the rear of the driver
then push the driver forward while holding it in this position
until it passes the upper bumper assembly
21
5. Remove guide rods
6. Remove upper bumper assembly.
7. Pull driver back towards you (or rear of tool). Lift up driver
while rotating driver clockwise until driver clears rail locator
casting. Remove driver from tool. Refer to Figure O.
8. Replace driver and follow steps in reverse to reassemble
9. Ensure new driver slides smoothly through the tool before
full reassembly.
10. Return the driver, guide rods, bumpers and housing end cap
back onto the unit. It is important to try the alignment of the
driver and the flywheel before screwing the housing end
cap back on to the unit. This can be done by connecting
a battery and pushing then releasing the nose of the
unit against a bench or hard surface. This will start the
motor spinning.
nOTE: When the driver and the flywheel are correctly
aligned, you will hear the motor coast back down from
full speed. If the driver and the flywheel are not correctly
aligned, the motor may not start up, may slow down much
faster than normal along with a loud grinding noise from
the unit. If this happens remove and reseat the driver
making sure the bumpers are seated correctly.
WARNING: Always test the unit by firing 40 mm staples
in Speed 1 into scrap material, to ensure that the tool is
working properly. If tool does not operate properly, contact
a recognised D
WALT service centre immediately.
E
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
18
on either side
19
. Refer to Figure M.
20
until you hear a click,
22
.
. Refer to Figure N.
English
15
Advertisement
