Sanyo MPX-CD163 Instruction Manual page 38

CLOCK SET-3
CLOCK SET SETTINGS
Use the cursor button to select
5
TIMER-A "T-1 :00" (minutes), and
– +
then use the setting buttons to set
the minutes to "00".
(TIMER SET)
TIMER-A
T-1 04:00
T-2 00:00
T-3 00:00
T-4 00:00
Use the cursor button to select
6
TIMER-A "T-2 00:" (hours), and then
– +
use the setting buttons to set the
hours to "6".
(TIMER SET)
TIMER-A
T-1 04:00
T-2 06:00
T-3 00:00
T-4 00:00
Use the cursor button to select
7 TIMER-A "T-2 00" (minutes), and
then use the setting buttons to set
– +
the minutes to "30".
(TIMER SET)
TIMER-A
T-1 04:00
T-2 06:30
T-3 00:00
T-4 00:00
Repeat steps 4 and 5 to set the
hours and minutes for T-3 and T-4
also.
Use the same procedure to set the
8
hours and minutes for T-1, T-2, T-3
– +
and T-4.
(TIMER SET)
TIMER-A
T-1 04:00
T-2 06:30
T-3 12:30
T-4 18:00
Note:
Initial settings T-1 to T-4 are "00:00"
In this case, the timer will operate at all times set by T-1.
The time divisions of the timer settings (T-1 to T-4) are
continuous settings in one cycle from start time to end time.
For instance, in the case of T-1 (4:00) and T-2 (6:30), the
domain of timer T-1 is from 4 a.m. until 6:30 a.m.
If two more timers are set to the same starting time, the
timers will operate together for the same period of time.
When setting the timers, a setting cannot be entered if, for
instance, T-3 as been set to earlier than T-1. If this happens,
re-enter the correct settings.
English
TIMER-B
T-1 00:00
T-2 00:00
T-3 00:00
T-4 00:00
TIMER-B
T-1 00:00
T-2 00:00
T-3 00:00
T-4 00:00
TIMER-B
T-1 00:00
T-2 00:00
T-3 00:00
T-4 00:00
TIMER-B
T-1 06:00
T-2 08:00
T-3 14:30
T-4 20:00
Example2: Set the timer operation as follows
To set TIMER-A time zones to automatic switching
screen and monitor mask.
To set TIMER-B timer zones to program recording and
motion sensor.
Use the cursor button to select
1
SEQUENCE "A", and then use the
– +
setting buttons to set "A". (TIMER-A
setting)
Use the cursor button to select
2
PROGRAM REC "A", and then use
– +
the setting buttons to set "B".
(TIMER-B setting)
Use the cursor button to select
3
MASK "A", and then use the setting
– +
buttons to set "A".
Use the cursor button to select
4
MOTION SENSOR "A", and then
– +
use the setting buttons to set "B".
Press the BACK button.
5
The setting will then be completed and the
BACK
display will return to the CLOCK SET
screen.
Press the BACK button once more to
return to the MAIN MENU screen.
CLOCK SET-3
– 37 –
SEQUENCE A
PROGRAM REC A
MASK A
MOTION SENSOR A
SEQUENCE A
PROGRAM REC B
MASK A
MOTION SENSOR A
SEQUENCE A
PROGRAM REC B
MASK A
MOTION SENSOR A
SEQUENCE A
PROGRAM REC B
MASK A
MOTION SENSOR A