D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network Adapter User Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Network Card
  5. DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...
  6. User manual

D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network Adapter User Manual

Product manual
Hide thumbs Also See for DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network Adapter:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network Adapter

Summary of Contents for D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network Adapter

  • Page 2: Preface

    Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date Description May 1, 2006 • DGE-560T Revision A1/A2 •...

  • Page 3: Table Of Contents

    Warranty..............44 Windows Vista (32/64-bit) ......10 ® ™ Linux ..............11 Registration..............50 Novell Netware ..........13 Novell Netware 5.10 ......... 13 Novell Netware 6.x ........... 14 FreeBSD ............15 Verify Installation ............ 16 D-Link DGE-560T User Manual...

  • Page 4: Product.overview

    With the D-Link DGE-560T, your PC can be connected to an Ethernet, Fast Ethernet, or Gigabit Ethernet network. The PC must be equipped with a PCI Express x1 expansion slot; alternatively the D-Link DGE-560T can be installed in a PCI Express x4, x8 or x16 expansion slot.

  • Page 5: Package Contents

    Netware 5.10 and Netware 6.x., or FreeBSD 5.x (Intel x86) Minimum.System. • Pentium 150MHz or Faster Requirements • 64MB RAM • 32MB Free Hard Drive Space • One Available PCI Express Slot (x1, x4, x8, or x16) • CD-ROM Drive D-Link DGE-560T User Manual...

  • Page 6: Features

    • Linux kernel 2.4.13 and higher stable version • Microsoft Network Client for DOS (NDIS 2 driver) • NetWare Client for DOS (ODI driver) . Note: The D-Link Network Control Program is not supported under Windows Vista ™ D-Link DGE-560T User Manual...

  • Page 7: Hardware Overview

    The indicator lights yellow when the port is connected to a 1000Mbps Gigabit Ethernet Network and the indicator lights green when the port is connected to a 100Mbps Fast Ethernet Network. Otherwise, this indicator remains off when the port is connected to a 10Mbps Ethernet Network. D-Link DGE-560T User Manual...

  • Page 8: Installation

    Install the Drivers 1. With your computer on, insert the D-Link CD into your CD-ROM Drive. When the autorun screen appears, click Install.Drivers. If you are installing this adapter in Linux, Netware, or FreeBSD, click View.Other.Drivers. . Note: If the Autorun CD function does not automatically start on your computer, go to Start > Run. In the run command box type “D:\ Autorun.exe”...

  • Page 9: Hardware Installation

    6. Replace the computer chassis cover. Reconnect the power and switch the computer power on. If the BIOS section of your computer’s boot program is plug-and-play compliant, then at power-up the BIOS will automatically configure any newly installed adapter. Skip to page 16 to verify your installation. D-Link DGE-560T User Manual...

  • Page 10: Alternate Installation

    To install the driver, click NEXT. In case the driver does not have a Microsoft Digital Signature yet, the window “Digital Signature Not Found” is displayed. 10. To continue the installation, click YES. The window “Completing the Found New Hardware Wizard” is displayed. 11. Click FINISH to complete the installation. D-Link DGE-560T User Manual...

  • Page 11: Windows ® Xp And Server 2003 (32-Bit)

    “Hardware Installation” is displayed. 10. To continue the installation, click Continue.Anyway. In the window “Found New Hardware Wizard”, the menu “Completing the Found New Hardware Wizard” is displayed. 11. Click FINISH to complete the installation. D-Link DGE-560T User Manual...

  • Page 12: Windows ® Xp And Server 2003 (64-Bit)

    Click NEXT. The menu “What do you want the wizard to do?” is displayed. Select the check box Specify.the.location.of.the.driver.(Advanced). Proceed with step 4 of the installation procedure described in section “Windows XP and Windows Server 2003 (32-bit)” ® on the previous page. D-Link DGE-560T User Manual...

  • Page 13: Windows ® Vista ™ (32/64-Bit)

    The window “Browse for driver software on your computer” is displayed. Browse the path to the driver and click Next. The window “Windows has successfully updated your driver software” is displayed. 10. Click Close to complete the installation. D-Link DGE-560T User Manual...

  • Page 14: Linux

    • The Linux kernel source must be stored in the directory /usr/src/linux. The kernel source and the kernel version have to be consistent. • A compilation tool, e.g. “gcc”, has to be installed on your Linux system. D-Link DGE-560T User Manual...
  • Page 15 The driver is now compiled and loaded. This process can take a few minutes. For more information on the Installation Mode or any information on the Patch Generation Mode, refer to the corresponding readme file or to the kernel documentation (which usually can be found in the directory /usr/src/linux/ Documentation/ on your system). D-Link DGE-560T User Manual...

  • Page 16: Novell Netware

    7. Select the driver for your network adapter. The message “Do you want to copy driver <driver name>.LAN?” is displayed. 8. To copy the driver to the server, select YES. If an older version of a D-Link driver is installed on the system, the messages “Save existing file SYS:SYSTEM\<driver name.LAN?”...

  • Page 17: Novell Netware 6.X

    To get a list of available drivers, press <Enter>. The menu “Select a driver” is displayed. To install an unlisted driver, press <Insert> (the D-Link driver is not listed). To specify the path to the driver, press <F3>. The window “Specify a directory path” is displayed.

  • Page 18: Freebsd

    If you use DHCP, add DHCP instead of the local IP address: ifconfig_myk0=”DHCP” Thus, the interface is configured. Repeat step 7 for each network adapter installed. Reboot your system. On reboot, the driver will be loaded and the network adapter will be configured automatically. D-Link DGE-560T User Manual...

  • Page 19: Verify Installation

    2000 and XP: Click on the System icon. Click the Hardware tab and then click Device.Manager. ® Windows Vista : Click on System.and.Maintenance and then click on Device.Manager. ™ Step.3: Scroll down and click the plus (+) sign next to Network Adapters. The D-Link.DGE-560T.Gigabit.CardBus.PC.Card will be listed. D-Link DGE-560T User Manual...

  • Page 20: Configuration

    Configure your Adapter After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e router) automatically. To verify your IP address, please see follow the steps below: Windows 2000/XP: Click on Start >...
  • Page 21 : Click on Start > Control. Panel > Network. and. Internet > Network. and. Sharing. Center > Manage. network. ™ connections. Step.2 Right-click on Local.Area.Connection which represents your D-Link network adapter and select Properties. Step.3 Highlight Internet.Protocol.(TCP/IP) and click Properties. Step.4 Click Use.the.following.IP.address and enter an IP address that is on the same subnet as your network or the LAN IP address on your...
  • Page 22 Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step.5 Click OK twice to save your settings. D-Link DGE-560T User Manual...

  • Page 23: Troubleshooting

    Confirming.the.Connection.(LED.Indicator) When the computer is powered “ON” and the D-Link DGE-560T is inserted into an open PCI Express slot, please check the following items if your LED light is not “ON”. When all items are working, your D-Link DGE-560T’s ACT/Link LED light should light up green (“linkage”...
  • Page 24 Start at the beginning of the “Quick Install Guide”. If you see symbols such as yellow exclamation point or red “X” over the icon adjacent to “D-Link DGE-560T Gigabit PCI Express Ethernet Adapter”, your adapter is not installed properly or may have a problem. Double-click the “D-Link DGE-560T Gigabit PCI Express Ethernet Adapter”, and read the explanation of the problem.
  • Page 25 ” for D-Link DGE-560T. It will help you to detect potential cabling issues such as cable ® opens, cable shorts, and impedance mismatches. 1. Insert the CD-ROM that came with your D-Link DGE-560T Gigabit PCI Express Ethernet Adapter into your CD-ROM drive. 2. Choose Drivers > Virtual.Cable.Tester, and click Install.the.package.
  • Page 26 10Mbps, 100Mbps, or 1000Mbps. (If no link is up, “no link” is displayed.) • Not.present—Cable pair is not present. This applies for network adapters which can only run with speeds of 10Mbps and 100Mbps and therefore do not use all cable pairs. D-Link DGE-560T User Manual...
  • Page 27 Start MS-DOS Prompt. Type in following: ping:xxx.xxx.xx.xx, where xxx.xxx.xx.xx is the IP address to be pinged (i.e. 192.152.81.85). In this case, computer A is pinging its own IP address. A successful ping will show four replies. D-Link DGE-560T User Manual...

  • Page 28: Network.control.program

    Network Control Program The D-Link Network Control Program is used to monitor the adapter and create VLAN information including VLAN Identifier and name for the system in which it is installed. Please follow procedures for installing D-Link Network Control program.
  • Page 29 2. Click Next. 3. Check I.accept.the.terms.in.the.license.agreement radio button and click Next. D-Link DGE-560T User Manual...
  • Page 30 4. Click Next. 5. Click Install. D-Link DGE-560T User Manual...
  • Page 31 6. Click Finish. D-Link.Network.Control.Program. To launch the D-Link Network Control Program, go to Start > Settings > Control.Panel then double-click the D-Link Network Control icon in the Control Panel folder. Note: D-Link Network Control Program can be installed and used on Windows ®...
  • Page 32 OK. Click the menu tab for the menu you want to view. Note: The Power Management and Sensors functions are not currently supported on the adapter. To add VLAN ID, click the Virtual LAN menu tab. D-Link DGE-560T User Manual...
  • Page 33 In the Add Virtual LAN pop-up menu, select the Virtual LAN ID (VID) number used for the system. A Virtual LAN Name can also be created but is optional. The Add Virtual LAN menu is also used to configure Jumbo Frames, Transmit Buffers, and Receive Buffers. Click OK. D-Link DGE-560T User Manual...

  • Page 34: Advanced Adapter Configuration

    The DGE-560T supports advanced features including the SNMP agent described in the SNMP Agent section in this manual, and support for 802.1p priority. To enable or disable 802.1p support on the adapter, right-click on the Local. Area. Connection. icon in Network. Connections.and click Properties. Click the Configure button. D-Link DGE-560T User Manual...
  • Page 35 Use the Advanced Configuration menus to configure 802.1p, select 802.1p.Support from the Property list and select On to enable or Off to disable from the Value drop-down list menu. Other advanced configuration features that can be changed or enabled include Flow Control, Jumbo Frames, Log Status Messages, Transmit and Receive buffers and others. D-Link DGE-560T User Manual...

  • Page 36: Snmp.agent

    2000, Server 2003, Server 2003 x64 Edition, XP or XP 64-bit operating system. The SNMP Agent includes ® MIB files used for device management using a MIB browser. 1. To launch the SNMP Agent installation program, double-click on PC.Agent. D-Link DGE-560T User Manual...
  • Page 37 3. Select the location for the agent. The default location is in the Program File folder. To select a different location, click Browse and find the preferred location or type a complete file name and path in the Browse menu. To continue click on Next. D-Link DGE-560T User Manual...
  • Page 38 4. Select the Program Folder in which the file will be located and click on Next. 5. Select Yes,.I.want.to.restart.my.computer.now and click Finish. D-Link DGE-560T User Manual...

  • Page 39: Using The Snmp Agent

    Windows start up can be enabled or disabled as desired. When the SNMP Agent is active, a MIB browser can be used for device management. These MIB files are located in the D-Link PC Agent folder. The three MIB files are included with the SNMP Agent are named: •...
  • Page 40 To manually launch the SNMP Agent program, go to the Start menu, open the Programs folder (if you chose to install it in a different folder open that folder), find the D-Link.PC.Agent folder, open it and double-click the D-Link.PC.Agent icon. Configure Name, Location and Contact information in the Personal Setting menu and click OK.
  • Page 41 To change your personal settings, enter information as desired in the spaces provided and click OK to save the changes. To change the administrative password, click the Password button in the Options menu tab of the D-Link Ethernet Adapter Agent menu.
  • Page 42 The D-Link Ethernet Adapter Agent maintains and allows the user to view an error log for the adapter. To view the error log click on the Error Log tab to select it. The error log is displayed: To save the error log to the system’s hard disk, click the Save button and choose a location at the prompt. To delete all log entries click...

  • Page 43: Networking.basics

    When the two modems have tested the phone-line quality and have switched to the combination of parameters, which will provide the best data communication, then you are given the “connect” message which signals the end of the inter-modem negotiation and the beginning of your intended communication with the remote computer. D-Link DGE-560T User Manual...
  • Page 44 The line will remain ready without further auto-negotiation action until the link is broken. Auto-negotiation then reoccurs at any time that the link is restored, again making the line ready for optimal data communications. D-Link DGE-560T User Manual...

  • Page 45: Technical.specifications

    • Activity/Link • Speed (Yellow: 1000Mbps; Green: 100Mbps; Off: 10Mbps) Network.Data.Transfer.Rate: • Ethernet: 10Mbps (Half-duplex) • Ethernet: 20 Mbps (Full-duplex) • Fast Ethernet: 100Mbps (Half-duplex) • Fast Ethernet: 200Mbps (Full-duplex) • Gigabit Ethernet: 2000Mbps (Full-duplex) D-Link DGE-560T User Manual...

  • Page 46: Technical.support

    • Hardware Revision (located on the label on the adapter (e.g. rev A2)) • Serial Number (s/n number located on the label on the adapter). You can find software updates and user documentation on the D-Link website as well as frequently asked questions and answers to technical issues.

  • Page 47: Warranty

    Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
  • Page 48 Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link;...
  • Page 49 • The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595 Mt.
  • Page 50 RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT.
  • Page 51 The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. D-Link DGE-560T User Manual...
  • Page 52 This device has been designed to operate with an antenna having a maximum gain of 2 dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. D-Link DGE-560T User Manual...

  • Page 53: Registration

    Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.1 September 26, 2007 D-Link DGE-560T User Manual...

Table of Contents