Table of Contents
Advertisement
SETTING UP YOUR VCR/DVD COMBINATION
Playing Dolby Digital (5.1 channel), DTS or MPEG audio
Connecting an amplifier with a Dolby Digital/ DTS/ MPEG Audio digital surround processor to your VCR/DVD's coaxial digital
jack provides richer and more powerful audio play.
C C Digital connection to a processor or amplifier with an optical/ coaxial digital input jack
You can make this connection using either a coaxial digital cable or an optical digital cable.
To OPTICAL
DIGITAL OUT jack
(commercially available)
To OPTICAL
DIGITAL input jack
NOTES:
• This connection is not possible if the processor or amplifier to which you want to connect does not have an optical/
coaxial digital input jack.
• ANALOG AUDIO OUT and AV (TV) of the VCR/DVD are not available on the DTS audio.
Optical cable (not supplied)
• Optical cable (not supplied) may be damaged when bent at sharp angles. Ensure cables are coiled in loops with a diame-
ter of 15 cm or more when storing them.
• Use a cable which is 3m or shorter.
• Insert cable plugs firmly into the connectors when making connections.
• If a plug has minor scratches or is dirty, clean it with a soft cloth before inserting it into a connector.
VCR/DVD SET UP
Turning on Your VCR/DVD
The following steps should only be performed if there is a
power failure or if this unit is unplugged for more than 1 hour.
1
Turn on the TV and select the video channel on the TV.
2
Press OPERATE, then VCR.
3
Press K or L repeatedly to select your desired language.
4
Press MENU.
Changing the Language
1
Press VCR, then MENU.
2
Press K or L to select INITIAL, then press B.
3
Press K or L to select LANGUAGE, then press B.
4
Press K or L repeatedly to select your desired language,
and MENU to confirm.
Video Channel Setting
Video Channel setting will be necessary, if your VCR/DVD is
connected to the TV via the round coaxial cable.
1
Press VCR.
2
Insert a pre-recorded tape into the cassette compart-
ment.
Playback will start automatically.
If playback does not start, press PLAY.
3
Select and adjust your TV to channel 37.
• If the playback picture appears on the TV screen, con-
9
tinue with step
.
DVD
DIGITAL
AUDIO
S-VIDEO
AUDIO OUT
OUT
OUT
L
OPTICAL
COAXIAL
R
To COAXIAL
DIGITAL OUT jack
Optical digital cable
Coaxial digital cable
(commercially available)
DIGITAL IN
OPTICAL
COAXIAL
VCR
DVD/VCR
COMPONENT
AUDIO OUT
AUDIO IN
VIDEO OUT
Y
L
L
C
R
R
B
VIDEO IN
VIDEO OUT
C
R
Dolby Digital (5.1 ch)/DTS/
MPEG Audio processor or amplifier
To COAXIAL
DIGITAL input jack
• If channel 37 is set for broadcasting, or interference
lines appear on the picture, the RF converter must be
set to a different channel between CH28 and CH69.
Continue with step
4
Press MENU.
5
Press K or L repeatedly to select INITIAL, then press B.
6
Press K or L repeatedly to select RF OUT, then press B.
The RF OUT CH menu will appear.
7
Press K or L to select a channel which is not used for
broadcasted between channel 28 and channel 69 in your
area, and B to confirm.
8
Press MENU to exit.
Set the TV channel to the RF OUT CHANNEL which was
selected on the VCR/DVD. A picture from the VCR/DVD
will appear on the TV screen. If a picture does not
appear, repeat steps
which is not used for broadcasting.
9
Press STOP to stop the tape.
NOTES:
• You may also access the RF OUT CH menu by press-
ing and holding MENU on the remote control for 3 sec-
onds during power off until the RF OUT CH menu
appears.
• If this unit and your TV are connected using a SCART
cable, the RF converter may be switched off to avoid
any possibility of interference. To switch off the RF con-
verter, follow steps
L repeatedly until "--" appears next to RF OUT CH.
Press B, then press MENU to exit.
– 12 –
AERIAL
RF OUT
4
4
to
8
using a different channel
and
to
above and press
1
4
6
EN
Advertisement
Table of Contents
