Table of Contents
Advertisement
SETTING UP YOUR VCR/DVD COMBINATION
Playing Dolby Digital (5.1 channel), DTS or MPEG audio
Connecting an amplifier with a Dolby Digital, DTS, or MPEG Audio digital surround processor to your VCR/DVD's coaxial dig-
ital jack provides richer and more powerful audio play.
C C Digital connection to a processor or amplifier with a coaxial digital input jack
You can make this connection using a coaxial digital cable.
NOTE:
• This connection is not possible if the processor or amplifier to which you want to connect does not have a coaxial digital
input jack.
• ANALOG AUDIO OUT and AV (TV) of the VCR/DVD are not available on the DTS audio.
VCR/DVD SET UP
Turning on Your VCR/DVD
The following steps should only be performed if there is a
power failure or if this unit is unplugged for more than 1 hour.
1
Turn on the TV and select the video channel on the TV.
2
Press OPERATE, then VCR.
3
Press K or L repeatedly to select your desired language.
4
Press MENU.
Changing the Language
1
Press VCR, then MENU.
2
Press K or L to select INITIAL, then press B.
3
Press K or L to select LANGUAGE, then press B.
4
Press K or L repeatedly to select your desired language,
and MEMU to confirm.
Video Channel Setting
Video Channel setting will be necessary, if your VCR/DVD is
connected to the TV via the round coaxial cable.
1
Press VCR.
2
Insert a pre-recorded tape into the Cassette compart-
ment.
Playback will start automatically.
If playback does not start, press PLAY.
3
Select and adjust your TV to channel 36.
• If the playback picture appears on the TV screen, con-
10
tinue with step
.
• If channel 36 is set for broadcasting, or interference
lines appear on the picture, the RF converter must be
set to a different channel between CH22 and CH69.
Continue with step
4
Press MENU.
DVD
DIGITAL
ANALOG
AUDIO OUT
AUDIO OUT
COAXIAL
To COAXIAL
DIGITAL AUDIO
OUT jack
4
.
S-VIDEO
OUT
VCR
AV2 (DECODER)
L
DVD/VCR
AV1 (TV)
R
Coaxial digital cable
(commercially available)
DIGITAL IN
COAXIAL
To coaxial digital
input jack
5
Press K or L repeatedly to select INITIAL, then press B.
6
Press K or L repeatedly to select RF OUT, then press B.
The RF OUT CH menu will appear.
7
Press K or L to select a channel which is not used for
broadcasted between channel 22 and channel 69 in your
area, and B to confirm.
8
Press TAPESPEED/SYSTEM to select G or K according
to your TV's setting for clearer sound.
9
Press MENU to exit.
Set the TV channel to the RF OUT CHANNEL which was
selected on the VCR/DVD. A picture from the VCR/DVD
will appear on the TV screen. If a picture does not
appear, repeat steps
which is not used for broadcasting.
10
Press STOP to stop the tape.
NOTES:
• You may also access the RF OUT CH menu by press-
ing and holding MENU on the remote control for 3 sec-
onds during power off until the RF OUT CH menu
appears.
• If this unit and your TV are connected using a SCART
cable, the RF converter may be switched off to avoid
any possibility of interference. To switch off the RF con-
verter, follow steps
L repeatedly until "--" appears next to "RF OUT CH".
Press B, then press MENU to exit.
– 12 –
AERIAL
RF OUT
Dolby Digital (5.1 ch) /
DTS / MPEG Audio
processor or amplifier
4
9
to
using a different channel
1
4
6
and
to
above and press
EN
Hide quick links:
Advertisement
Table of Contents
