HP Surestore 330fx - Optical Jukebox Manual
Capacity upgrade for c1104/05 series jukeboxes - c1159-90001
Hide thumbs
Also See for Surestore 330fx - Optical Jukebox:
- Faq (34 pages) ,
- Command reference manual (378 pages)
Table of Contents
Advertisement
Quick Links
For C1104/05 Series Jukeboxes
This upgrade requires code to be downloaded to the controller PCA and the drives.
BEFORE starting this upgrade, obtain the following:
*
The downloadable code required for this upgrade. FTP this code
from hpgrsg.gr.hp.com (15.38.89.10
Further download instructions are available at that address.
* A PC with a SCSI interface and appropriate cables.
* A utility to download the code - DOWNLD2 or HP TOOLSET (Version 1.95ce
or later) from CoComp
Capacity Upgrade
Important! Read This First
)
using an "anonymous" login.
HP Part No. C1159-90001
Printed in USA June, 1996
Edition 1 0596
Advertisement
Table of Contents
Related Manuals for HP Surestore 330fx - Optical Jukebox
Summary of Contents for HP Surestore 330fx - Optical Jukebox
-
Page 1: Capacity Upgrade
Capacity Upgrade For C1104/05 Series Jukeboxes Important! Read This First This upgrade requires code to be downloaded to the controller PCA and the drives. BEFORE starting this upgrade, obtain the following: The downloadable code required for this upgrade. FTP this code from hpgrsg.gr.hp.com (15.38.89.10 using an "anonymous"... - Page 2 Hewlett-Packard Company, 1996...
-
Page 3: Esd Precautions
Capacity Upgrade For C1104/05 Jukeboxes Before upgrade: Upgraded to the equivalent of a: (# of drives and slots) C1104F/G/H C1107F/G/H (238 slots) (4 drives, 128 slots) C1105F/G/H (6 drives, 128 slots) Table 1: C1104/05 Series Capacity Upgrade Options a. After you install this capacity upgrade (C1159F/G/H), you are able to install 1 or more 2-drive upgrades ( C1158F/G/H). -
Page 4: Kit Contents
Kit Contents • 24 - magazine guides, 8 slot (makes 12 sets) — # C1100-44x00 • 6 - magazine guides, 6 slot (makes 3 sets) — # C1160-41x15 • 1 - interposer PCA — # C1107-60x05 • 1 - controller PCA — # C1107-60x01 •... -
Page 5: Before You Begin
Before You Begin Caution Do NOT switch off power to the jukebox until you are sure the . Switching off the jukebox when the SCSI bus is inactive SCSI bus is active can cause data loss and/or indeterminate bus states. When doing this upgrade, be sure that disk cartridges are not If you need to remove moved from their original slot locations. - Page 6 Installing a Capacity Upgrade Caution When doing this conversion, be sure that disk cartridges are If you need to not moved from their original slot locations. remove the cartridges, record their SLOT LOCATIONS and ORIENTATION so they can be replaced to their ORIGINAL positions.
- Page 7 Figure 2: Screws on the RFI panel Caution Put on a grounding strap to work inside the outer shell of this jukebox. 3. Install the 110 cartridge slots. Refer to Figure 1 for an overview of where these slots will be added Note Fot this kit, magazines (sets of cartridge slots) come in 12 sets of 8-slot and 3 sets of 6-slot.
- Page 8 Figure 3: Location of 8-slot and 6-slot magazine sets after upgrade Figure 4: Magazine tabs and spring latch (right side)
- Page 9 The magazine guide above is shown as it is oriented when placing it into the inside right of each stack (as you face the stacks). Place the leading tabs (top right in the picture) into the slots farthest in, then rotate the magazine guide into the stack, catching the trailing tabs (lower left arrows in picture).
- Page 10 a. Place the power supply on the power supply bracket. Make sure all cables are out of the way. b. Mount the new power supply with 2 T-20 screws through mount tabs on the top of the power supply. 5. Install the new SCSI interface module. Note The new interface module you will assemble has 2 SCSI interface PCAs to support future upgrades to the number of...
- Page 11 ((Place the interface module and interface board aside.)) 4. Install the new, lower interposer PCA below the one currently in the jukebox. Figure 6 shows the location of this PCA and Figure 7 shows how cables are routed from the upper interposer PCA and the new, lower interposer PCA.
- Page 12 Figure 8: GPIO cable connection to the lower interposer PCA d. Place the additional ferrite clip that comes with this kit around the new SCSI cable going to the upper interposer PCA. Attach this clip on top of the one is currently there. See Figure 9 for placement.
- Page 13 5. Attach the power cables. Refer to Figure 10 for proper power cable connections. Figure 10: Paths for connection of power cables a. Connect the interposer PCA power cable. 1. Connect the 2 connectors on the power cable to the lower interposer PCA (at the upper and middle power connectors on the right side of the interposer PCA).
- Page 14 Figure 11: Installing the first (lower) PCA with standoff screws Figure 12: Installing the second (upper) PCA - adding jumper c. Mount the new interface module on the jukebox. 1. Connect the upper interposer-to-interface SCSI cable to the “bottom” SCSI interface PCA (“bottom”...
- Page 15 Figure 13: Connecting Cables to the SCSI rpeater/converter PCA 2. Rotate the interface module up against the jukebox chassis, insert and tighten the 4 T-20 mounting screws. Caution Make sure that the cables are not pinched by the side of the interface module, and can be moved freely.
- Page 16 Note In the first step, below, leave the top cables attached to the controller PCA to hold this PCA in place when its mounting screws are removed. a. Remove all cables (except the top cables - see Note above) from the controller PCA. b.
- Page 17 Figure 15: Connecting the drive fan cables to the lower interposer PCA 8. Download the latest code to the controller PCA and drives. You will use an external SCSI connector on the interface module. 9. Run the Wellness Test to verify installation. 10.
- Page 18 Note Choose the correct product label based on the FINAL product configuration 1/2 capacity (128 slots) 6 drives = C1105 F/G/H Full capacity (238 slots) 6 drives = (use labels from capacity upgrade kit) 8 drives = C1108F/G/H 10 drives = C1110F/G/H 12 drives = C1112F/G/H Choose the label that has the same product suffiix (F, G, or H) that the original product had.