JVC BD-X200E Instructions Manual page 64

Synchronous Recording
Recording Playback Signals From a VCR with RS-422A (continued)
2. Deleting the In Point, Out Point, and Chapter Marks
REMOTE CONTROL SCREEN ( 9PIN MASTER )
EXIT IN POINT 00:00:00:00
: : :
h m s f
1 00:00:00:00 2
4 00:25:00:00 5
7 00:40:00:00 8
CHAPTER MANUAL
ADJ
8.0 Mbps
BITRATE
TC SET EDL LOAD
w
TC CANCEL EDIT/END
3. Starting the Record Process
REMOTE CONTROL SCREEN ( 9PIN MASTER )
EXIT IN POINT 00:00:00:00
: : :
h m s f
1 00:00:00:00 2
4 00:25:00:00 5
7 00:40:00:00 8
CHAPTER MANUAL
ADJ
BITRATE 8.0 Mbps
TC SET EDL LOAD
TC CANCEL EDIT/END
EDIT/END
Notes
Editing accuracy is ±5 frames.
If no In Point has been registered, recording will begin at the current tape position. However, the tape must be positioned
before the Out Point and all chapter marks for this to be possible.
If no Out Point has been registered, a manual stop must be carried out to end recording. Select EDIT/END to end the editing
process.
When the chapter auto-create function is used, chapters will be created at specific intervals.
REMOTE CONTROL SCREEN ( 9PIN MASTER )
EXIT IN POINT 00:00:00:00 OUT POINT
: : : : : :
h m s f h m s f
00:00:00:00 00:15:00:00
1 2
4 00:25:00:00 5 00:30:00:00
7 00:40:00:00 8 00:45:00:00
TC INPUT
CHAPTER MANUAL
ADJ
BITRATE 8.0 Mbps DISC REMAIN
TC SET EDL LOAD
TC CANCEL EDIT/END
ADJUST
4. Ending the Record Process
If you intend to play the recorded disc on this DVD recorder or on another player, select FINALIZE and press the SET button.
Once finalizing has been carried out, no addition recordings can be made on the disc.
To remove the recorded disc from your BD-X200, press the OPEN/CLOSE button on the front panel.
E-62
q
OUT POINT 00:10:00:00
: : : : : :
h m s f h m s f
00:15:00:00 3 00:20:00:00
00:30:00:00 6 00:35:00:00
00:45:00:00 9 00:50:00:00
: : :
TC INPUT
000 min
DISC REMAIN
FINALIZE
OUT POINT 00:10:00:00
: : : : : :
h m s f h m s f
00:15:00:00 3 00:20:00:00
00:30:00:00 6 00:35:00:00
00:45:00:00 9 00:50:00:00
: : :
TC INPUT
000 min
DISC REMAIN
FINALIZE
Setting the Optimum Bit Rate
ADJUST can be used to set the optimum bit rate (i.e., the amount of data per
00:10:00:00 second) for the remaining space on a disc based on the recording time (or duration)
: : : between the In Point and the Out Point.
h m s f
00:20:00:00
3
6 00:35:00:00
DISC REMAIN displays an estimate of the available space for recording on the
9 00:50:00:00
: : :
current disc.
000 min
FINALIZE BIT RATE displays the current bit-rate setting.
To set the bit rate that best suits the remaining disc capacity, select ADJUST and
then press the SET button.
FINALIZE
q Use the cursor buttons (t, 8, 7, and 6) to select the point to
be deleted (i.e., In Point, Out Point, or a chapter mark from the
chapter list), and then press the SET button.
w Use the cursor buttons (t, 8, 7, and 6) to select TC CANCEL
and press the SET button.
The selected point (i.e., the In Point, Out Point, or a chapter
mark from the chapter list) will be deleted.
Whenever a chapter mark is deleted, the chapter list will be
resorted.
q Select EDIT/END from the REMOTE CONTROL screen and
press the SET button.
VCR will begin playback by returning to the position 5 seconds
before the IN POINT.
The unit will start record when the VCR reaches the IN POINT.
Recording of video and audio from the VCR to the DVD will be
carried out from the In Point to the Out Point with chapters
being created as specified.
w When playback reaches the Out Point, title recording will end
automatically.
The VCR will automatically adopt STOP mode at this time.
The DVD recorder will return to Stop mode and will end title
recording.
If another title is to be recorded, repeat operations from the
registration of the In Point and Out Point.