Tightening Torques - Husqvarna SMR Owner's Manual

ENGINE
Application
Camshaft cap fastening screw
Rocker arm axle plug
Cylinder head cover fastening screw
Cylinder head fastening nut
Cylinder head and cylinder fastening nut
Oil hose to cylinder head fastening screw
Oil hole plug on conrod pin
Primary drive driving gear fastening nut
Centrifugal disc on INTAKE CAMSHAFT fastening
screw
Timing chain slider fastening screw
Crankcase bearings plates fastening screw
Engine oil drain plug
Engine oil filter plug
Engine oil filter cartridge cover fastening screw
(TC-TXC)
Carburetor union fastening screw
Alternator fastening nut
Stator plate fastening screw
Spark plug
Pick-up fastening screw
Clutch hub and disc housing fastening nut
Starting gears stop plate fastening screw
Gearbox forks driving shaft fastening screw
Gear control click and plate fastening screw
Gear shift position sensor fastening screw
Water pump rotor fastening nut
Water pump body fastening screw
Drive sprocket seal ring plate fastening screw
92

TIGHTENING TORQUES

± 5%
MOTEUR
Threading
M6x1 12 Nm
M14x1,5 (+LOCTITE 243) 25 Nm
M6x1 8 Nm
M8x1,25 15 Nm
M10x1,5 (+MOLIKOTE HSC) 37 Nm+90°
M10x1 15 Nm
M14x1 (+LOCTITE 243) 20 Nm
M18x1,25 (+LOCTITE 243) 180 Nm
M6x1 (+LOCTITE 243) 8 Nm
M8x1,25 12 Nm
M6x1 (+LOCTITE 272) 11 Nm
M16x1,5 25 Nm
M14x1,5 25 Nm
M5x0,8 (+LOCTITE 243) 6 Nm
M4x0,7 (+LOCTITE 272) 3 Nm
M12x1 75 Nm
M6x1 (+LOCTITE 272) 8 Nm
M10x1 10÷12 Nm 7.4÷8.9 ft/lb
M5x0,8 (+LOCTITE 272) 6 Nm
M18x1 75 Nm
M6x1 (+LOCTITE 243) 8 Nm
M8x1,25 (+LOCTITE 243) 20 Nm
M6x1 (+LOCTITE 243) 8 Nm
M5x0,8 (+LOCTITE 243) 6 Nm
M5x0,8 (+LOCTITE 243) 3,9 Nm
M6x1(+LOCTITE 542) 8 Nm
M5x0,8 (+LOCTITE 243) 6 Nm
CHASSIS
Application
8.7 ft/lb Rear frame lower fastening screw
18.4 ft/lb Engine guard fastening screw
5.8 ft/lb Rear chain roller fastening screw
10.8 ft/lb Side stand fastening screw
27.5 ft/lb+90° Rear frame upper fastening screw
10.8 ft/lb Frame to engine plate fastening screw
14.5 ft/lb Engine lower fastening screw
Clutch and front brake controls clamp fastening screw
130 ft/lb
Throttle control holders fastening screw
5,8 ft/lb
Front brake hose upper fastening screw (TE, SMR)
Front brake hose upper fastening screw (TC-TXC)
8.9 ft/lb
Rear brake control pedal fastening screw
7.9 ft/lb
Rear brake pump fastening screw
18.4 ft/lb
Front brake pump plate fastening screw (SMR)
18.4 ft/lb
Rear brake fluid tank fastening screw
4.3 ft/lb
Rear stop control switch (TE, SMR)
2.2 ft/lb
Front control switch connector fastening screw (SMR)
55.3 ft/lb
Rear brake pedal adjusting cam fastening screw
5.8 ft/lb
Front brake hose guide plate fastening screw
Front brake tank cap fastening screw (SMR)
4.3 ft/lb
Front fork legs fastening screw
55 ft/lb
Front wheel axle fastening screw
5.8 ft/lb
Steering bearings adjusting ring nut
14.5 ft/lb
Steering pivot fastening nut
5.8 ft/lb
4.3 ft/lb Handlebar upper clamp
2.9 ft/lb Handlebar holder fastening screw
5.8 ft/lb Front fork legs guard fastening screw
4.3 ft/lb Front fork legs ring guard fastening screw
Rear swing arm axle fastening nut
Rear swing arm to rocker arm fastening nut
± 5%
Threading
M8x1,25 25,5 Nm 18.8 ft/lb
M6x1 14,7 Nm 10.8 ft/lb
M8x1,25 26,95 Nm 19.9 ft/lb
M8x1,25 (+LOCTITE 243) 11,75 Nm 8.7 ft/lb
M8x1,25 25,5 Nm 18.8 ft/lb
M8x1,25 (+LOCTITE 270 35,3 Nm 26 ft/lb
M8x1,25 35,3 Nm 26 ft/lb
M6x1 4,9 Nm 3.6 ft/lb
M6x1 4,9 Nm 3.6 ft/lb
M10x1 19 Nm 14 ft/lb
M10x1 24,7 Nm 18.2 ft/lb
M10x1,25 (+LOCTITE 243) 41,65 Nm 30.7 ft/lb
M6x1 10,4 Nm 7.7 ft/lb
M6x1 10,4 Nm 7.7 ft/lb
M6x1 2,45 Nm 1.8 ft/lb
M10x1 19 Nm 14 ft/lb
M2x0,4 0,8 Nm 0.6 ft/lb
M6x1 14,7 Nm 10.8 ft/lb
M6x1 6 Nm 4.4 ft/lb
M6x1 4,9 Nm 3.6 ft/lb
M8x1,25 25 Nm 18.4 ft/lb
M6x1 10,4 Nm 7.7 ft/lb
M25x1 3,45 Nm 2.5 ft/lb
M24x1 83,3 Nm 61.4 ft/lb
M8x1,25 28,4 Nm 20.9 ft/lb
M10x1,5 21,1 Nm 15.6 ft/lb
M5x0,8 7,85 Nm 5.8 ft/lb
M5x0,8 2,45 Nm 1.8 ft/lb
M16x1,5 (+LOCTITE 243) 122,5 Nm 90.3 ft/lb
M12x1,25 80 Nm 59 ft/lb