Advertisement
3oWINg
CONNNCTION
INSTNUCTmONS
For existing installations
ONLY, refer to Figure 9.
t
Follow
the power
supply
kit manufacturer's
Installation
Instructions
supplied with the strain relief
clamp
and install.
See Figure 7.
2
Insert the end connectors
fbr line 1, line 2 and neutral and
tighten securely to the terminal block. See Figure 7.
DO NOT LOOSEN
the factory installed nut
connections
which
secure the range wiring to the terminal
block.
Electrical failure or loss of electrical
connection
may
occur if these 3 nuts are loosened
or removed.
3
Make sure all connections
are tightened securely and replace
the rear access cover. See Figure 7.
GROUND|NG
|NSTRUCT|ONS_
ONLY 3_W|RE CONNECT|ONS:
A ground
strap is installed
on this range which connects
the center
terminal
of the neutral
terminal
block
to the range chassis.
The
ground
strap is connected
to the range by the center, lowest screw.
See Figm*e 9. The ground strap must not be removed
unless Nation,d,
State or Local
Codes
do not permit
use of a ground
strap.
Note:
tf the ground
strap is removed
tbr any reason,
a separate
ground
wire
must
be connected
to the separate
ground
screw
attached
to the rauge
chassis
aud to an adequate
ground
source.
3 & 4oWINN
PENN&NNNT
WINN CONNNCTION$
3-_ire
permanent
connection
- follow steps 1, 2 and 5 belo_.
4-wire permanent
connection
- fbllow a!l steps below.
mNSTALLATmON
MANUAL
Befbre wiring the range, re_ ie_ the suggested power source location
drawings in Figure 2. If connecting
to a 4-wire electrical
system:
i
Follow the manufacturer's
Installation
Instructions
supplied
with the strain relief clamp and install.
2
Strip insulation
away fi*om the ends of the permanent
wiring
for line 1, line 2 and neutral; also strip ground wire on 4-wire
connections.
Tighten all 3 or 4-wire leads to the terminal block.
Follow wire locations shown in Figure 10.
DO NOT LOOSEN
the factory installed nut
connections
which secure the range wiring to the terminal
block. Electrical
failure or loss of electrical
connection
may
occur if these 3 nuts are loosened or remo_ ed.
Note: For 3-wire permanent
connection
skip steps 3 and 4 and
continue with step 5.
3
Disconnect
the ground strap. Remoxe the factory installed
ground screw and plate to release the factory installed copper
ground strap from frarne of the range. Cut and discard
the
copper strap from the terminal block. KEEP the ground screw,
ground plate and go to step 4.
4
Connect the green ground wire lead to the frame of the range
using the ground screw and plate as shown in Figure 11. Be sure
to install using the same hole in the frame where the ground
screw was originally installed.
5
Make sure all connections
are tightened securely and replace
the rear access coxer. See Figure 7.
Note: Non-terminated
field wire compression
connections must
be set at approximately
90 in./lbs.
Connect {_ne
1 here
Discard ground strap
and ground plate
Connect green insulated
copper grourld wire with
ground screw here
Figure
8
_r
"
terminal block
Nete:
Install strain relief
c_amp Center or white
wire must always be
Connect
attached to the center
terminal on block¸
Connect neutral (white or
center) here
A user supplied strain
relief clamp must be
rlstalled at this
location
It requires 1
s/u-inches (35 cm}
diameter cord kit hole
\\\\
\'\\
Figure
t O
Connect E_ne
1 here
Ground slra
Note:
install strain relieI
clamp Center must
always be attached to the
center terminal on block
Figure
9
Connect neutral here
A user supplied strain relief
clamp must be installed at
diameter cord kit hole
\\\\\,
wire lead
Advertisement
