Table of Contents
Advertisement
ON: Enables the PLAYBACK AUTO mode.
OFF: Disables the PLAYBACK AUTO mode.
Note: Set to OFF when a WJ-DR200 AV Disc Recorder
is connected to the unit.
5. PASSWORD
This item lets you select whether to permit free or limited
access to the Setup menus. When PASSWORD is set to
ON, the operator must enter the password to access the
menus. Enter a 4-digit password consisting of numbers
from 1 to 9 (except 0).
1. Move the cursor to the PASSWORD parameter.
2. Select ON or OFF by pressing the + or – button.
The initial factory setting is OFF.
5-1. Password registration
ON 1111-9999:
Password required to access the Setup menus.
1. Select ON by pressing the + or – button.
2. Move the cursor to the desired (first) digit by press-
ing the A or B button.
3. Select the desired number by pressing the + or –
button.
4. Repeat steps 2 and 3 until all digits are registered.
OFF: No password required to access the Setup
menus (access is free).
5-2. Reply to password request
If PASSWORD parameter is set to ON, the operator is
requested to type the password to access the Setup
menus.
1. Press the MENU/ESC button for 2 seconds or more.
The password inquiry screen prompts you to type the
password.
2. Type the 4-digit password by pressing the CAMERA
SELECT buttons 1 through 9, and the A or B button.
3. The Setup menu appears if the typed password is cor-
rect. If a wrong password is typed, the screen displays
"NG" and returns to the screen before the MENU/ESC
button was pressed.
4. To retry repeat steps 1 and 2.
5-3. Changing the password
The password currently registered can be changed as fol-
lows.
1. Press the MENU/ESC button for 2 seconds or more to
display the password inquiry screen. Then type in the
current password by pressing the CAMERA SELECT
buttons, and the A or B button. The SETUP menu
appears.
2. In the SYSTEM SETUP menu, select ON for the PASS-
WORD parameter.
3. Move the cursor to the first (desired) digit by pressing
the A or B button.
18
4. Select the desired number by pressing the + or – but-
ton.
5. Repeat step 3 and 4 until all digits are registered.
6. After registration the new password is required when
the operator accesses the SETUP menus.
6. PWR ON MODE
This parameter lets you select a display pattern for your
startup screen. When the power is turned on, the picture is
displayed in the selected pattern.
1. Move the cursor to the PWR ON MODE parameter.
2. Select 1-16 (1-9 for WJ-FS109) or SPOT SEQ. The initial
factory setting is 1.
1-16: Spot picture of selected channel is displayed.
Note: 10-16 are not available for WJ-FS109.
SPOT SEQ: A sequence of spot pictures is displayed.
7. VTR KEY LOCK
This item lets you enable or disable the VTR/CAM Selection
button. Select ON to protect the REC OUT signal from
being interrupted by accidental operation of the VTR/CAM
Selection button.
1. Move the cursor to the VTR KEY LOCK parameter.
2. Select ON or OFF by pressing the + or – button.
The initial factory setting is OFF.
ON: Disables VTR/CAM Selection button.
OFF: Enables VTR/CAM Selection button.
Note: The VTR/CAM Selection button is also disabled
when PLAYBACK AUTO is set to ON.
8. ENCODE
This item lets you adjust parameters for playing back
tapes that are recorded on a Panasonic system or a non-
Panasonic system.
1. Move the cursor to the ENCODE parameter.
2. Select PANA or OTHERS by pressing the + or – button.
The initial factory setting is PANA.
PANA: Select this, if the tape was recorded on a
Panasonic Multiplexer system.
OTHERS: Select for non-Panasonic system.
Advertisement
Table of Contents
