DeWalt DW745 Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Saw
  5. DW745
  6. Instruction manual
DeWalt DW745 Instruction Manual

DeWalt DW745 Instruction Manual

Heavy-duty 10" (254 mm) job site table saw
Hide thumbs Also See for DW745:

Advertisement

Table of Contents

See also: Instruction Manual , User Manual
Инструкция
DeWALT DW745
Перейти в карточку товара
8 800 775 98 98

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DW745

Summary of Contents for DeWalt DW745

  • Page 1 Инструкция DeWALT DW745 Перейти в карточку товара 8 800 775 98 98...
  • Page 2 DW745 Heavy-Duty 10" (254 mm) Job Site Table Saw Scie circulaire à table de chantier robuste avec lame de 254 mm (10 po), DW745 Sierra de banco para el lugar de trabajo de 254 mm (10") de alta resistencia DW745...

  • Page 4: Polarized Plugs

    trated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, Defi nitions: Safety Guidelines may be used to connect this plug to a matching two-conductor receptacle as shown in The definitions below describe the level of severity Fig.

  • Page 5: Additional Safety Rules For Table Saws

    • MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing • USE RECOMMENDED ACCESSORIES. Use only accessories that are recommended starter keys. The unauthorized start-up of a machine by a child or visitor may result in by the manufacturer for your model. Accessories that may be suitable for one tool may injury.
  • Page 6 • NEVER CUT FERROUS METALS (those with any iron or steel content), CEMENT SAW BLADE GUARD AND SPLITTER BOARD OR MASONRY. Certain man-made materials have special instructions for Your table saw is equipped with a blade guard and splitter assembly that covers the blade cutting on table saws.

  • Page 7: Specifications

    been damaged during shipping. If any parts are missing or damaged, contact your dealer to • lead from lead-based paints, replace them before attempting to assemble the tool. • crystalline silica from bricks and cement and other masonry products, and Refer to Figure 2 for the loose items and hardware included with the saw: •...
  • Page 8 3. Remove the arbor nut (Y) and outer washer (Z) and set aside. FIG. 4 4. Place the blade (C) on the arbor making sure the FIG. 6 teeth of the blade point downward and toward the front of the saw. 5.
  • Page 9 TO ATTACH THE PUSH STICK (FIG. 4) 1. Remove the throat plate. (Refer to Throat The push stick included with the DW745 mounts to the right of the saw under the blade Plate.) wrench storage. To attach the push stick to the saw, align the slots in the handle of the stick 2.
  • Page 10 2. Drive four 3-1/2" (88.9 mm) long screws through the holes in the metal frame. Make sure the screws extend through the frame and securely attach to the supporting work surface. If marring the supporting work surface is a concern, the DW745 can be mounted to scrap FIG. 17 FINE ADJUSTMENT KNOB (FIG. 17) wood which can then be clamped onto the desired work surface.
  • Page 11 NOTE: Your saw is fully and accurately adjusted at the factory at the time of manufacture. If FENCE ALIGNMENT ADJUSTMENT (Blade Parallel to Fence) readjustment due to shipping and handling or any other reason is required, follow the steps If you experience fence alignment problems and want to correct an out of parallel between below to adjust your saw.

  • Page 12: Saw Blades

    Part A – Adjusting the Bevel Scale System (Fig. 22, 23) 2. Do not saw warped, bowed or cupped wood. The work piece must have one straight, 1. Remove the blade guard from the saw and raise the blade all the way up in the table. smooth side to go against the rip fence or miter gauge.

  • Page 13: Bevel Ripping

    the blade and use a push stick to feed the work piece if there is less than 6" (152 mm) Crosscutting between the fence and the blade. WARNING: NEVER touch the “free end” of the work piece or a “free piece” that is cut FIG.

  • Page 14: Maintenance

    For further detail of warranty coverage and warranty repair informa- Your table saw is equipped with a dust shroud tion, visit www.dewalt.com or call 1-800-4-D WALT (1-800-433-9258). This warranty does and dust collection port. For best results,...
  • Page 15 English...
  • Page 16 Push Stick Pattern Modèle de poussoir Patrón de la vara de empuje Adjust length of push stick so hand will clear blade guard and rip fence. Régler la longueur du poussoir de sorte que la main sera dégagée du protège-lame et du guide longitudinal. Ajuste el largo de las varas de empuje para que la mano no obstruya el protector de la hoja y la guía de corte longitudinal.
  • Page 18 WALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286 (DEC06) Form No. XXXXXX-XX DW745 Copyright © 2006 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box...
  • Page 19 DeWALT DW745 Описание Характеристики...

Table of Contents