Shutting Down The Projector; Troubleshooting Your Setup - Toshiba TDP-MT8 User Manual

MT8 User's Guide.fm Page 11 Friday, November 22, 2002 9:09 AM

Shutting down the projector

Power Save
7KH SURMH.WRU KDV D 3RZHU 6DYH IHDWXUH LQ WKH 6\VWHP PHQX WKDW DXWRPDWL
.DOO\ WXUQV WKH ODPS RII DIWHU QR VLJQDOV DUH GHWH.WHG IRU  PLQXWHV $IWHU 
DGGLWLRQDO PLQXWHV ZLWK QR VLJQDO WKH SURMH.WRU SRZHUV GRZQ ,I DQ D.WLYH
VLJQDO LV UH.HLYHG EHIRUH WKH SURMH.WRU SRZHUV GRZQ WKH LPDJH LV GLVSOD\HG
<RX PXVW SUHVV WKH Power EXWWRQ WR GLVSOD\ DQ LPDJH DIWHU  PLQXWHV KDYH
SDVVHG
Turning off the projector
7R WXUQ RII WKH SURMH.WRU SUHVV WKH Power EXWWRQ DQG YHULI\ WKDW \RX ZDQW WR
WXUQ WKH SURMH.WRU RII E\ SUHVVLQJ WKH SRZHU EXWWRQ DJDLQ ZLWKLQ  VH.RQGV
7KH ODPS WXUQV RII DQG WKH /(' EOLQNV JUHHQ IRU DERXW RQH PLQXWH ZKLOH WKH
IDQV .RQWLQXH WR UXQ WR .RRO WKH ODPS :KHQ WKH ODPS KDV .RROHG WKH /('
OLJKWV JUHHQ DQG WKH IDQV VWRS 8QSOXJ WKH SRZHU .DEOH WR .RPSOHWHO\ SRZHU
RII WKH SURMH.WRU

Troubleshooting your setup

,I \RXU LPDJH DSSHDUV .RUUH.WO\ RQ WKH V.UHHQ VNLS WR WKH QH[W VH.WLRQ
SDJH   ,I LW GRHV QRW WURXEOHVKRRW WKH VHWXS
7KH /(' RQ WRS RI WKH SURMH.WRU·V NH\SDG LQGL.DWHV WKH VWDWH RI WKH SURMH.WRU
DQG .DQ KHOS \RX WURXEOHVKRRW
Table 2: LED behavior and meaning
LED color/behavior
solid green
blinking green
blinking red
The projector will not start up if the LED
is blinking red. You must correct the prob-
lem, disconnect and reconnect the power
cable, then power on the projector.
See page 34 for more information on
blinking red LEDs.
solid red
7KH IROORZLQJ WDEOH VKRZV VRPH SRWHQWLDO SUREOHPV ,Q VRPH .DVHV PRUH
WKDQ RQH SRVVLEOH VROXWLRQ LV SURYLGHG 7U\ WKH VROXWLRQV LQ WKH RUGHU WKH\
DUH SUHVHQWHG :KHQ WKH SUREOHP LV VROYHG \RX .DQ VNLS WKH DGGLWLRQDO
VROXWLRQV
11
Meaning
The projector is plugged in, or the projec-
tor has been turned on and the software
has initialized. The projector has been
turned off and the fans have stopped.
The Power button has been pressed and
the software is initializing, or the projec-
tor is powering down and the fans are
running to cool the lamp.
A fan (blinks 4 times) or lamp (blinks 3
times) failure has occurred. Turn off the
projector and wait one minute, then turn
the projector on again. Also check for a
blocked vent or a stopped fan (blinks 5
times).
An unidentifiable error: please contact
Technical Support.