Table of Contents
Advertisement
d) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
e) Use the power tool, accessories and tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the manufacturer. A charger that
is suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may cause
irritation or burns.
SERVICE
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool is
maintained.
Electrical Safety
The electric motor has been designed for one voltage only. Always check that the
power supply corresponds to the voltage on the rating plate. 230 V AC means your
tool will operate on alternating current. As little as 10% lower voltage can cause loss
of power and can result in overheating. All D
tool does not operate, check the power supply. Your D
therefore no earth wire is required.
WALT tools are factory tested; if this
E
WALT tool is double insulated,
E
• Young children and the infirm. This appliance is not intended for use by
young children or infirm persons without supervision. Young children should be
supervised to ensure that they do not play with this appliance.
• Replacement of the supply cord. If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised D
to avoid a hazard.
Extension Cords
CAUTION: Use only extension cords that are approved by the country's Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.
MINIMUM GAUGE FOR CORD SETS
For Cable length (m): 7.5
Use Cable with minimum rating (Amperes)
Tool Amperes
0 - 3.4
7.5
3.5 - 5.0
7.5
5.1 - 7.0
10
7.1 - 12.0
15
12.1 - 20.0
20
Safety Information for Lasers and IR Thermometers
WARNING: Laser Radiation Exposure. Do not disassemble or modify the
IR thermometers. There are no user serviceable parts inside. Serious eye injury
could result.
WARNING: Hazardous Radiation. Use of controls or adjustments or performance
of procedures other than those specified herein may result in hazardous radiation
exposure.
• Do not operate the IR thermometers in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.
• Use the IR thermometer only with the specifically designated D
batteries. Use of any other batteries may create a risk of fire.
• Store the IR thermometer out of reach of children and other untrained
persons. Lasers are dangerous in the hands of untrained users.
2
WALT Service Centre in order
E
15
25
30
45
60
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
10
15
10
10
10
15
15
15
15
15
20
20
20
20
20
25
–
WALT
E
Advertisement
Table of Contents
