FO-DC635U CONTENTS CHAPTER 1. GENERAL DESCRIPTION Circuit description of control PWB ....5-1 Caution............1-1 Circuit description of CIS unit ......5-15 Specifications ..........1-3 Circuit description of LIU PWB ....5-16 Operation panel..........1-4 Circuit description of operation panel PWB ..5-18...
FO-DC635U CHAPTER 1. FO-DC635U GENERAL DESCRIPTION Service Manual [1] Caution 1. Laser caution This laser printer is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH or IEC60825-1 standard. This means that this machine does not produce a hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Page 5
FO-DC635U 3. Caution for Battery replacement (French) ATTENTION (Danish) ADVARSEL ! Il y a danger d'explosion s' il y a remplacement incorrect Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. de la batterie. Remplacer uniquement avec une batterie du Udskiftning må kun ske med batteri af samme fabrikat og type.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
FO-DC635U [3] Operation panel Display This displays messages and prompts to help you operate the machine. The backlight turns on whenever a key is DOCUMENT COMMUNICATION SYSTEM touched, and then automatically turns off after a preset time if no further operations are performed. The display can be...
Page 8
FO-DC635U TIMER key UP and DOWN arrow keys Press this key to set a fax operation to be performed Volume setting: Press these keys to change the speaker automatically at a later time. volume when the SPEAKER key has been pressed, or the ringer volume at any other time.
FO-DC635U [4] Transmittable documents 4. Cautions on Transmitting Documents • Documents written in yellow, greenish yellow, or light blue ink can- 1. Document Sizes not be transmitted. • Ink, glue, and correcting fluid on documents must be dry before the...
FO-DC635U [5] Installation 2) Connecting the telephone line cord Insert one end of the line cord into the jack on the back of the 1. Site selection machine marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line wall telephone jack.
Page 11
FO-DC635U 3. Installing the print cartridges (Toner cartridge: 3) If you are replacing the drum cartridge, remove the old cartridge and dispose of it according to local regulations. FO-50ND)(Drum cartridge: FO-47DR) Follow the steps below to install or replace the toner and drum car- tridges.
The handle can be left standing up. when approximately 1000 pages before the drum needs replace- ment). Use the following replacement drum cartridge. Sharp FO-47DR drum cartridge 4. Loading printing paper BLUE You can load up to 250 sheets of letter or legal paper (max. 20 lbs.) in the paper tray.
FO-DC635U 4) Replace the received document tray. 4) Place a stack of paper in the cassette, print side up. • The received document tray must be attached for the machine • Make sure the stack of paper is not higher than the two tabs on to operate properly.
Page 14
FO-DC635U 3) Close the operation panel, making sure it clicks into place. 4) Remove the jammed paper. • Make sure no torn pieces of paper remain in the print compart- ment and rollers. 7. Clearing a jammed printing paper 5) Replace the drum cartridge.
Page 15
FO-DC635U 8. Replacing the Verification Stamp (FO-45VS) 9. Installing the Dual Line Kit (FO-60DL) If you are using the Verification Stamp function, you will need to Note: The FO-60DL Dual Line Kit cannot be installed if the FO-NP1 replace the ink cartridge in the stamp unit when it runs out of ink (when Network Printer Kit is installed.
Page 16
FO-DC635U 5) a: Attach the LIU board to the metal plate, positioning the modular 9) Connect the cable to the LIU board and the dual line control board. jacks as shown. The bottom edge of the board should fit into the Secure the core band with the 10 mm screw.
Page 17
FO-DC635U 10. Installing the paper cassette option FO-CS2 (2nd) Important! Be sure to turn off the power and unplug the power cord before proceeding. 1) Remove the packing material and tape from the second paper cas- sette. 2) Remove the covers from the sides of the first cassette (the cassette...
Page 18
FO-DC635U 11. Caution when installing paper cassette option FO-CS2(2nd) to FO-DC635 When installing the option FO-CS2 to FO-DC635U as a 2nd paper cassette, the short pins and cables on the paper cassette PWB must be recon- nected. FO-DC635 1st Paper Cassette...
FO-DC635U 12. Quick reference guide SPEED DIAL To store a Speed Dial number, press and enter a number 12.1. SENDING FAXES START/ Place your document (up to 50 letter-size pages) face down in the doc- from 1 to 200 (press if you entered a 3-digits).
FO-DC635U CHAPTER 2. FO-DC635U ADJUSTMENTS Service Manual [1] Adjustments General Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary. 1. Adjustments Adjustments of output voltage (FACTORY ONLY) 1. Install the power supply unit in the machine.
Page 21
If F100 is Replacement parts open, replace it with a new one. ICP-S0.5 (Sharp code: VHViCPS05//-1) 4) F101 (ICP-S1.8) is installed in order to protect IC’s from an over- ICP-S0.7 (Sharp code: VHViCPS07//-1) current generated in the TX motor drive circuit.
FO-DC635U [2] Diagnostics and service soft switches 1.2. Print diagnosis This diagnosis is concerned with the print which is used for production 1. Operating procedure and service support. Entering the diagnostic mode Two kinds of diagnoses are supported. 1.1. Fax diagnosis...
Page 23
FO-DC635U 2. Diagnostic items description • Switching ON/OFF of ECM during the use of image memory. • OFF to ON of telephone billing function which is using the image 2.1. Fax diagnosis memory is used (Note: In the existing set, the telephone billing code function is specified from OFF to ON when the timer sys- 2.1.1 (A) Soft switch mode...
Page 24
FO-DC635U 2.1.4 (D) Auto feeder mode 2.1.7 (G) Optical adjust mode By executing the document insertion and discharge, the automatic The optical system is adjusted. feeding function can be checked. And the document sensor can be • By pressing down the “START” key, the document reading lamp checked as well.
Page 25
FO-DC635U 2.1.12 (L) Flash Memory check NOTE: Before entering this mode, a FAX/TEL number or an E-MAIL must be stored in the RAPID key [01]. (This program will not This is a mode to check that the flash memory acts normally. The flash be executed if there is no data stored, or otherwise a program memories shown in the following table are checked.
Page 26
FO-DC635U • When the REPORT key is input, the memory dump list is produced 2.1.21 (U) LCD check mode from the displayed address (here, it is limited at the 16-byte bound- This is an item to check that the LCD acts normally.
Page 27
FO-DC635U 2.2. Print diagnosis 2.2.2 Rapid key 02: Check pattern 1 The lateral stripe 2 pattern is printed on one sheet. 2.2.1 Rapid key 01: Area print mode 1 (Black 2 line and white 2 line are repeated.) The effective printing area frame is printed in the specified sheet size.
Page 28
FO-DC635U 2.2.7 Rapid key 07: Paper feed aging 2 3. After input of 6 digits, shift to another counter with the "#" and " " keys as necessary. When all necessary counters are com- This is a mode that is used for aging related to printing, and there are pletely input, press the START key.
Page 29
FO-DC635U 2.2.12 Rapid key 12: Life clear mode 2. In the state 1, input the DEL key, and the counter will be respec- tively cleared. The mode is used to respectively clear the life counter of the printer 3. “CLEARED” is displayed and clearing is complete. After ending one and the counter of the auto feeder.
Page 30
FO-DC635U 4. Soft switch description 4.1. Soft switch • Soft switch (U: For U.S.A./C: For Canada) DATA Switch setting and function Initial ITEM Remarks setting Recall interval OPTION Set to 1~15 Binary input No. = 1 4 (Data No.) eg. Recall interval is set to 5 min.
Page 31
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Time display format 24 hours 12 hours-AM/PM Date display format Month-Day-Year Day-Month-Year Header print Footer print DIS receive acknowledge Follows the setting of SW7 No.3. Once during G3 transmission 1...
Page 32
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Memory retransmission OPTION times Binary input No. = 1 4 (Data No.) eg. Retransmission time set to 10 times. SW10 Memory retransmission OPTION interval Binary input No. = 5 8 (Data No.) V.34 mode transmission...
Page 33
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Reserved Reserved Reserved Reserved SW15 Cl Signal OFF detect (ms) 1200 enable time No. 5 No. 6 No. 7 No. 8 Reserved Reserved Reserved Reserved Distinctive ringing No. 5 No. 6 No.
Page 34
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Service condition for line-1 Line-1 No. 1 No. 2 No. 3 TX/RX (AUTO) TX/RX (MANU) RX only (AUTO) RX only (MANU) SW22 Other Setting Default Setting Reserved Reserved Reserved Reserved...
Page 35
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting JBIG (Joint Bi-level Image Group) JBIG (Joint Bi-level Image Group) option Modem speed V.33 V.17 V. 29 V. 27ter SW28 14400 1200 1440 12000 9600 7200 9600 7200 4800 2400 Reception speed fixed V.
Page 36
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting V.34 mode transmission speed Sending speed = 2400 (bps) x (N+1) Example : 2400 (bps) x 12 = 28800 (bps) 2400 (bps) is set for N=0. 33600 (bps) is set for N=14.
Page 40
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Duplex scan (Black line Continuous Black Line Count detection when reading for No. 1 No. 2 No. 3 No. 4 copies) Not used Other Duplex scan (Black page Black Line Percent detection when reading for No.
Page 41
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting F.A.S.T. (RMS) mode F.A.S.T. line Line 2 Line 1 Verification stamp OPTION Invalid if not mounted Day light saving OPTION SW61 Key buzzer volume High No. 5 No. 6 Reserved...
Page 42
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting The 2nd priority cassette No. 1 No. 2 No. 3 OPTION It is effective None only when Tray No.31-1/2 are 1st Cass. set up of man- Tray Other Combination SW66...
Page 43
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Reserved Reserved Reserved Reserved SW72 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW73 Data reduction (Except AUTO 100% Set up to 100% except the The number in notation: Setting prohibi-...
Page 44
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Cassette define LTR/A4: Tray Cassette define LTR/A4: When W cas- sette Cassette define LTR/A4: Ignore when W cassette SW77 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Metric based resolution Metric based resolution prefer red Don’t care...
Page 45
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Reserved Reserved Reserved Reserved SW83 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW84 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Waiting time of duplex scan SW85 Binary input No.
Page 46
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Reserved Reserved Reserved Reserved SW89 Reserved Reserved Reserved Reserved Method of detecting CI fre- Firmware Modem quency Network scan (Compatibil- G3 (1d) fax G3 (1d) Modified Huffman ity with IDM Viewer for TIFF...
Page 47
FO-DC635U DATA Switch setting and function Initial ITEM Remarks setting Network print: Auto con- Value tinue On/off Time 120s Network print: Default LETTER paper size SW96 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW97 Reserved Reserved Reserved Reserved Reserved...
Page 48
FO-DC635U 4.2. Soft switch function description SW4 No. 1 ~ No. 3 Communication results printout It is possible to obtain communication results after each transaction. SW1 No. 1 ~ No. 4 Recall interval Normally, the switch is set (No. 1: 0, No. 2: 0, No. 3: 1) so that the Choice is made for a recall interval for speed and rapid dial numbers.
Page 49
FO-DC635U SW5 No. 7 Substitute reception conditions SW8 No. 1, No. 2 Compromised equalizer Selection of substitute reception according to existence of TEL num- The specific line equalizer is inserted. ber from transmitting side. Initial setting allows substitute reception No. 1 No.
Page 50
FO-DC635U SW12 No. 4, No. 5 EOL detection timer SW16 No. 5 ~ No. 8 Distinctive ringing Used to make a choice of whether to use the 25-second or 13-second When the ringing setting is turned off, all of the CI signal are received.
Page 51
FO-DC635U SW19 No. 6 ~ No. 8 Reserved SW25 No. 1 ~ No. 4 Number of rings for auto-receive (0: No ring receive) Set to "0". When the machine is set in the auto receive mode, the number of rings SW20 No.
Page 52
FO-DC635U SW29 No. 4 Non-modulated carrier in V.29 transmission mode SW32 No. 3 Reserved Though transmission of a non-modulated carrier is not required for Set to "1". transmission by the V29 modem according to the CCITT Recommen- SW32 No. 4 ~ No. 6 Reserved dation, it may be permitted to send a non-modulated carrier before the image signal to avoid an echo suppression problem.
Page 53
FO-DC635U SW37 No. 7 Reserved SW41 No. 1 Reserved Set to "0". Set to "1". SW37 No. 8 Reserved SW41 No. 2 ~ No. 4 Reserved Set to "1". Set to "0". SW38 No. 1 ~ No. 4 Reserved SW41 No. 5 Reserved Set to "0".
Page 54
FO-DC635U SW48 No. 6, No. 7 Reserved SW60 No. 7 Admin transfer of DESKTOP-SCAN Set to "0". Determine whether or not to use “Stan to Desktop” as a forwarding address in the Document Admin function. SW48 No. 8 Reserved SW60 No. 8 Reserved Set to "1".
Page 55
FO-DC635U SW64 No. 2 Reserved SW66 No. 1 ~ No. 3 The 2nd priority cassette Set to "0". To select the second priority cassette. SW64 No. 3 Continuous serial polling 000: Not used (To set in case of using only paper feeder that has been set in the tray priority cas- Turns ON/OFF the continuous polling function.
Page 56
FO-DC635U SW70 No. 2 Reserved SW74 No. 2 Print out of total time and total number of pages on activity report Set to "0". Used to make a choice of whether the total communication time and SW70 No. 3 Reserved pages are recorded in the activity report.
Page 57
FO-DC635U SW76 No. 7 MTF correction in half-tone mode SW80 No. 5 Addition of header (Sender information) In the half tone mode, image area is separated from character area ON/OFF of addition of header (sender information) to various list is and processed separately to eliminate unclear character transmission.
Page 58
FO-DC635U SW86 No. 4, No. 5 Reserved SW90 No. 6 Reserved Set to "0". Set to "1". SW86 No. 6 Inbound print setting SW90 No. 7 Reserved Select an image print setting on the machine when using the Inbound Set to "0".
FO-DC635U SW96 No. 4 Network print: Default paper size When the selected paper size was other than the size that can be set in this unit (LTR, LGL, A4), an alternative paper size can be set with this SW. SW96 No. 5 ~ No. 7 Reserved Set to "0".
FO-DC635U CHAPTER 3. FO-DC635U MECHANICAL DESCRIPTION Service Manual [1] Mechanical description Refer to the service manual of FO-4470U. [2] Printer description Refer to the service manual of FO-4470U. [3] Disassembly and assembly procedures Refer to the service manual of FO-4470U and FO-DC535U.
FO-DC635U 17. Paper take-up roller Refer to the service manual of FO-4470U. 18. Print head unit (PH) Refer to the service manual of FO-4470U. 19. Paper empty sensor (PE1) Refer to the service manual of FO-4470U. 20. Fusing unit (1/2) Refer to the service manual of FO-4470U.
FO-DC635U CHAPTER 5. FO-DC635U CIRCUIT DESCRIPTION Service Manual [1] Circuit description 2. Description of each block 2.1. Main control block 1. General description This block consists of 32 bit RISC microcomputer HD6417706F133 In this machine, the facsimile control block except the printer control is (main component), flash ROM, 64 Mbit SDRAM, Main ASIC, Sub mainly composed of the units shown in Fig.
Page 68
FO-DC635U 2.1.3 W9864G6EH-7 (IC25): pin-54, TSOP (64 Mbit SDRAM) The program stored in the flash memory (IC12) mentioned in the above item 2) is downloaded to this SDRAM and used as a program execution memory. It is also used as various work memories and com- munication buffers.
Page 69
FO-DC635U HD6417706F133 (IC24) Terminal description (1/2) Name Function Name Function Address bus — RTC power supply (1.9 V) Vcc-RTC* Address bus XTAL2 On-chip RTC crystal oscillator pin Address bus EXTAL2 On-chip RTC crystal oscillator pin Address bus — RTC power supply (0 V)
Page 70
FO-DC635U HD6417706F133 (IC24) Terminal description (2/2) Name Function Name Function TxD2/ SCIF transmit data 2/SC port O/I/O DACK1/ DMA acknowledge 1/input/output SCPT[2] PTE[1] port E SCK2/ SCIF clock 2/SC port O/I/O DRAK0/ DMA request acknowledge/input/ SCP[3] PTE[2] output port E...
Page 71
FO-DC635U 2.1.4 LC272D0BT-WA6 (IC6): pin-216, QFP (MAIN ASIC) 6) CIS control and image processing The block has the following functions. That is control the CIS and The device is the embed-array, which has the following functions. A/D converts the scanning image data from analogue to digital, and 1) CPU interface executes the converted image data processing.
Page 72
FO-DC635U LC272D0BT-WA6 (IC6) Terminal description (1/2) Name Function Name Function Ground Ground Data bus XNICACK Acknowledge signal for NIC Data bus XNICINT Interrupt request from NIC board Data bus XNICCS Chip select (NIC Board) Data bus XJBG1 Reserved Data bus...
Page 73
FO-DC635U LC272D0BT-WA6 (IC6) Terminal description (2/2) Name Function Name Function Ground Ground TEST0 Test pin 0 TXAI1 Current control 1 (Phase A) TEST1 Test pin 1 TXAI0 Current control 0 (Phase A) XINSC Image block Clock in CRNT0 Current change signal 0...
Page 74
FO-DC635U 2.1.5 LC24199B-WJ0-E (IC21): pin-208, QFP (SUB ASIC) 4) RTC (Real Time Clock) LSI control Using serial communication to RTC, the device set and read the The device is the gate-array, which has the following functions. time. 1) PCU (Print Control Unit) interface...
Page 75
FO-DC635U LC24199B-WJ0-E (IC21) Terminal description (1/2) Name Function Name Function Ground Ground Not connect Not connect XCI1 CI detect signal DPOPCL10 GPO bus for PCL board ERLY0 Reserved for 200V DPOPCL11 GPO bus for PCL board GAINC0 Reserved for 200V...
Page 76
FO-DC635U LC24199B-WJ0-E (IC21) Terminal description (2/2) Name Function Name Function Ground Ground SD DICT in SDDCT Address bus DPANIC0 Address bus for NIC board Address bus DPANIC1 Address bus for NIC board Address bus DPANIC2 Address bus for NIC board...
Page 77
FO-DC635U 2.2. Backup memory block • TTL and CMOS compatible DTE interface This block consists of flash memory for the image memory and 256 - ITU-T V.24 (EIA/TIA-232-E) (data/control) Kbit SRAM backed up with a battery. The image memory has a stan-...
Page 78
FO-DC635U 2.3.3 Configurations, Signaling Rates, and Data Rates Configuration Modulation Carrier Frequency Data Rate Symbol Rate Bits/Symbol Bits/Symbol Constellation (Hz) ± 0.01% (bps) ± 0.01% (Symbols/Sec.) Data Points V.90 PCM — 56000 R/V.34 8000 Dynamic — — rates T(Note 4)
Page 80
FO-DC635U 2.4. Scanner control block 2.5. Speaker amplifier The speaker amplifier monitors the line under the on-hook mode, out- 2.4.1 Image signal process block puts the buzzer sound generated by SUB ASIC, ringer sound, DTMF The CIS is driven by MAIN ASIC (IC6), and the output video signal generated from the modem, and line sound.
FO-DC635U Pin name Pin No. Pin Description SENSE1 Set current detection pins. SENSE2 Connect these pins, fed back through noise filters, to E1, and E2. Current control pins by connecting between this pin and GND. DGND 4,11 Internal diode anode connection...
FO-DC635U [4] Circuit description of LIU PWB 1. LIU block operation description 1.1. Block diagram CONTROL TXA2 TXOUT TXOUT SURGE DIODE ACTIVE TXA1 LINE PROTECTION BRIDGE CHOKE CIRCUIT MODEM RXIN RXIN (FM336PLUS) DETECTOR EXT.TEL DETECTOR VREF SPKR CML0 CML0 CML0...
Page 83
FO-DC635U 1.3.7 Signal selection [Signals for status recognition according to input signals] The following signals are used to control the transmission line of FAX Signal Name Function signal. For details, refer to the signal selector matrix table. XCI0 Incoming call (CI) detection signal...
FO-DC635U [5] Circuit description of operation panel PWB 1. Operational description b) Structure and external shape Structure: 320 x 240 monographic display module 1) Operation panel PWB This dot matrix LCD module consists of an LCD panel, a print The operation panel PWB includes the ten key scan circuit and the PWB mounting electrical parts, a TCP electrically connecting LED lighting circuit.The LS145 is controlled through LD0~LD3 (4...
FO-DC635U [6] Circuit description of power supply PWB This unit supply input AC 120 V/60 Hz, +24 V, +5 V as block diagram shows. (See Fig. 12) Power relay +24VS AC OUT /HEATER_ON AC output circuit block /PWRLY Optical isolator...
FO-DC635U CHAPTER 6. FO-DC635U CIRCUIT SCHEMATICS AND PARTS LAYOUT Service Manual [1] Control PWB circuit 1. Main Control PWB Circuit CPU Block (1a/12) Main Control PWB Circuit CPU Block (1/2) 1/12 C274 C275 C219 +3.3VSHA C276 C218 C277 C217 +1.9VD...
Page 89
FO-DC635U 2. Main Control PWB Circuit CPU Block (1b/12) Main Control PWB Circuit CPU Block (2/2) 1/12 A[25:0] ( 2-1A)( 3-1A)( 4-6A)( 5-4A) ( 7-5C)(11-6A)(12-2F) R451 XTAL2 R303 R452 EXTAL2 D[31:0] 4.7K ( 2-2A)( 3-2A)( 4-6A)( 5-4A) ( 7-4C)(11-6A)(12-4D)(12-2D) AUDATA[0]/PTF[0]...
Page 117
FO-DC635U 4. Operation Panel PWB parts layout Note: Since the parts of PWB cannot be supplied, change it as a unit. DESCRIPTION PARTS CODE Panel PWB unit DCEKP425CXHP2 The OPERATION PANEL PWB of the model employs LED PWB unit DCEKP425CXHL3 lead-free solder.
Page 121
FO-DC635U 3. 1st Paper Cassette PWB parts layout (Top side) The 1ST PAPER CASSETTE PWB of the model employs lead-free solder. 4. 1st Paper Cassette PWB parts layout (Bottom side) The 1ST PAPER CASSETTE PWB of the model employs lead-free solder.
FO-DC635U CHAPTER 7. FO-DC635U OPERATION FLOWCHART Service Manual [1] G3 Protocol Refer to the service manual of FO-4470U. [2] Super G3 Protocol Refer to the service manual of FO-4470U. [3] Power on sequence Refer to the service manual of FO-4470U.
Page 129
FO-DC635U [3] Exterior etc.(3) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [3] Exterior etc.(3) Drive unit CMOTZ2146XH01 Core RCORF2149XHZZ Screw(3x10) XEBSD30P10000...
Page 130
FO-DC635U [4] Operation panel unit 26 24 PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [4] Operation panel unit LCD case,upper GCABA2406XHSB LCD case,under GCABB2408XHSB LCD cushion PCUSS2185XHZZ LCD FCC cable QCNWN293BXHZZ LED FCC cable QCNWN295BXHZZ LCD unit RUNTZ2095SCZZ Operation panel PWB unit...
Page 131
FO-DC635U [5] Document guide upper unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [5] Document guide upper unit Back bracket LANGF2819XHZZ Document guide upper plate LPLTM3011XHZZ Separator plate LPLTP2819XHZZ Transfer plate LPLTP2821XHZZ Document guide stopper LSTPP2052XHZZ Release lever MLEVP2304XHSC...
Page 132
FO-DC635U [6] Scanner frame unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [6] Scanner frame unit Scanner feed clutch CBSHP2079XH02 DR bearing LBSHP2113XHZZ Scanner frame LFRM-2201XHZA Scanner support plate LPLTM3012XHZZ CIS spring MSPRC3138XHZZ Pinch roller spring MSPRD3086XHZZ Stopper spring...
Page 133
FO-DC635U [7] Frame PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [7] Frame High voltage PWB unit [HV1] 0KW4127620702 Cooling fan motor [M2] 0KW4127610101 Washer 0KW1200152102 Rubber foot 0KW4122235013 Rubber foot 0KW4122234901 Auxiliary member 0KW4122235102 Print head ass'y [PH] 0KW4571075200...
Page 134
FO-DC635U [8] Paper transport section PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [8] Paper transport section Tension spring 0KW4127301903 0KW4127302601 0KW4127300701 Roller 0KW4127300201 Toner empty PWB unit [PWB-G] 0KW4127011301 Roller 0KW4127300101 0KW4127300802 Gear(14T) 0KW4127301401 Gear(32T) 0KW4127301003 Wire harness ass'y...
Page 135
FO-DC635U [9] Fusing unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [9] Fusing unit Heater,120V [H1] 0KW4127650202 Paper exit sensor [PS3] 0KW4127090102 Actuator 0KW4127551801 Holder 0KW4127553403 0KW4127557101 Bushing 0KW4127557201 Roller 0KW4127553601 Separator Separator 0KW4127553301 Pressure spring 0KW4109551601 Fusing bushing...
Page 136
FO-DC635U [10] Drive/Transfer unit 37 38 PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [10] Drive/Transfer unit Torsion spring 0KW4127201302 Interlock switch [S2] 0KW4109630501 0KW4127048301 I/C guide assy Drive gear assy 0KW4127030601 Main motor [M1] 0KW9314210121 Paper take up sensor switch...
Page 137
F O - D C 6 3 5 U [11] 1st paper cassette(1) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [11] 1st paper cassette(1) Cassette case GCASP2164XHSB LHLDW2238XHZZ Lock down holder LPLTM3237XHZZ Cassette push up plate Cassette push up plate holder LPLTP3230XHZZ Cassette back guide LPLTP3231XHZA...
Page 139
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [12] 1st paper cassette(2) Cassette cabinet GCABG2412XHSB Lever joint 1 LPLTP3023XHZZ Lever joint 2 LPLTP3044XHZZ Release lever MLEVP2309XHZZ Pinch roller spring MSPRC3095XHZZ Release lever spring MSPRD3093XHZZ Pinch roller NROLP2334XHZA Pinch roller shaft...
Page 140
FO-DC635U [13] Packing material & Accessories...
Page 141
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [13] Packing material & Accessories Operation Manual TINSE4515XHTZ Paper size labels TLABP391EXHZC Rapid key labels TLABZ392EXHZA Toner cartridge(Initial starter cartridge) DUNT-429CSCZZ Toner cartridge protection SPAKA344EXHZZ ADF exit tray CPLTP2803XHC5 Received document tray(with label)
Page 142
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] Control PWB unit Capacitor(50WV 2200PF) [C114] VCKYCY1HB222K Capacitor(50WV 2200PF) [C115] VCKYCY1HB222K Capacitor(50WV 2200PF) [C116] VCKYCY1HB222K Capacitor(50WV 2200PF) [C117] VCKYCY1HB222K Capacitor(50WV 2200PF) [C118] VCKYCY1HB222K VCKYCY1HB222K Capacitor(50WV 2200PF) [C119] Capacitor(50WV 0.1µ F)
Page 143
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] Control PWB unit Capacitor(25WV 0.1µ F) [C247] VCKYCY1EF104Z Capacitor(10WV 1µ F) [C248] VCKYCY1AF105Z Capacitor(25WV 0.1µ F) [C256] VCKYCY1EF104Z Capacitor(25WV 0.1µ F) [C258] VCKYCY1EF104Z Capacitor(50WV 1000PF) [C259] VCKYCY1HB102K VCKYCY1EF104Z Capacitor(25WV 0.1µ F) [C262] Capacitor(25WV 0.1µ...
Page 144
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] Control PWB unit Capacitor(25WV 0.1µ F) [C404] VCKYCY1EF104Z Capacitor(50WV 0.1µ F) [C407] VCKYCY1HF104Z Capacitor(25WV 0.1µ F) [C601] VCKYCY1EF104Z Capacitor(50WV 0.01µ F) [C602] VCKYCY1HB103K Capacitor(16WV 100µ F) [CE1] VCEAEA1CW107M RC-EZ3097XHZZ Capacitor(10WV 220µ F) [CE2] Capacitor(16WV 10µ...
Page 145
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] Control PWB unit IC(BA10393F) [IC23] VHIBA10393F-1 IC(HD6417706F133) [IC24] RH-IX2293XHZZ IC(W9864G6EH-7) [IC25] RH-IX0009FCPZ IC(TC58DVM72A) [IC26] RH-IX2363SCZZ (SN74LV245A) [IC29] VHI74LV245APW RH-IX2444XHZZ IC(FM336Plus) [IC30] IC(SN74LV4053APW) [IC31] RH-IX2320XHZZ IC(HA17358AFEL) [IC32] RH-IX2346XHZZ IC(SN74HCT244NSR) [IC33] RH-IX2300XHZZ...
Page 146
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] Control PWB unit Resistor(1/16W 470Ω ± 5%) [R128] VRS-CY1JB471J Resistor(1/16W 1KΩ ± 5%) [R129] VRS-CY1JB102J Resistor(1/16W 10KΩ ± 5%) [R130] VRS-CY1JB103J Resistor(1/16W 1.0MΩ ± 5%) [R131] VRS-CY1JB105J Resistor(1/16W 56KΩ ± 1%)
Page 147
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] Control PWB unit Resistor(1/16W 33Ω ± 5%) [R254] VRS-CY1JB330J Resistor(1/16W 10KΩ ± 5%) [R256] VRS-CY1JB103J Resistor(1/16W 10KΩ ± 5%) [R261] VRS-CY1JB103J Resistor(1/16W 1KΩ ± 5%) [R262] VRS-CY1JB102J Resistor(1/16W 10KΩ ± 5%)
Page 148
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] Control PWB unit Resistor(1/16W 33Ω ± 5%) [R451] VRS-CY1JB330J Resistor(1/16W 33Ω ± 5%) [R452] VRS-CY1JB330J Resistor(1/16W 10Ω ± 5%) [R455] VRS-CY1JB100J Resistor(1/16W 68Ω ± 5%) [R457] VRS-CY1JB680J Resistor(1/16W 10KΩ ± 5%)
Page 149
FO-DC635U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] Control PWB unit Resistor(1/16W 10KΩ ± 5%) [R607] VRS-CY1JB103J Resistor(1/16W 10KΩ ± 5%) [R608] VRS-CY1JB103J Resistor(1/16W 1KΩ ± 5%) [R609] VRS-CY1JB102J Resistor(1/16W 10KΩ ± 5%) [R613] VRS-CY1JB103J Resistor(1/16W 1KΩ ± 5%)