ABB FENA-01 Hardware Manual
  1. Manuals
  2. Brands
  3. ABB Manuals
  4. Adapter
  5. FENA-01
  6. Hardware manual

ABB FENA-01 Hardware Manual

Ethernet adapter module
Hide thumbs Also See for FENA-01:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
ABB Drives
Hardware Manual
Ethernet Adapter Module
FENA-01

Advertisement

Table of Contents
loading

Related Manuals for ABB FENA-01

Summary of Contents for ABB FENA-01

  • Page 1 ABB Drives Hardware Manual Ethernet Adapter Module FENA-01...
  • Page 3 Ethernet Adapter Module FENA-01 Hardware Manual 3AUA0000022986 REV A EFFECTIVE: 31.3.2008 © 2008 ABB Oy. All Rights Reserved.

  • Page 5: Safety Instructions

    Safety instructions Overview This chapter states the general safety instructions that must be followed when installing and operating the FENA-01 Ethernet Adapter module. The material in this chapter must be studied before attempting any work on, or with, the unit.
  • Page 6 Safety instructions...

  • Page 7: Table Of Contents

    Ethernet ........... . 11 The FENA-01 Ethernet Adapter module ......12 Compatibility .
  • Page 8 FENA-01 ........

  • Page 9: Introduction

    Introduction Intended audience The manual is intended for people responsible for installing, commissioning and using the FENA-01 Ethernet Adapter module. The reader is expected to have a basic knowledge of electrical fundamentals, electrical wiring practices and how to operate the drive.

  • Page 10: What This Manual Contains

    Safety instructions are featured in the first few pages of this manual. Overview contains short descriptions of the Ethernet networking, the FENA-01 Ethernet Adapter module and a delivery checklist. Mechanical installation contains placing and mounting instructions for the module. Electrical installation contains wiring, bus termination and earthing instructions.

  • Page 11: Overview

    Ethernet standards support a variety of physical media (coaxial cable, twisted pair, fiber optics) and topologies (bus and star). The FENA-01 Ethernet Adapter supports twisted pair as the physical media in a star topology. An example of an allowable topology is shown in Figure 1.

  • Page 12: The Fena-01 Ethernet Adapter Module

    The FENA-01 Ethernet Adapter module The FENA-01 Ethernet Adapter module is an optional device for ABB drives which enables the connection of the drive to an Ethernet network. Through the FENA-01 Ethernet Adapter module it is possible to: • give control commands to the drive (Start, Stop, Run enable, etc.)
  • Page 13 Hub, Switch or Router Diagnostic LEDs (See chapter “Diagnostics” in appropriate Protocol Manual) Ethernet connector X1 (see chapter "Electrical installation") Chassis Screw (see chapter "Electrical installation") Figure 2. The construction of the Ethernet link and the FENA-01 Adapter module. Overview...

  • Page 14: Compatibility

    Compatibility The FENA-01 is compatible with Ethernet standards IEEE 802.3 and IEEE 802.3u. Note that compatibility with these Ethernet standards does not imply support for any higher level protocols (eg, Modbus/TCP). Verify support for desired protocol and features with the appropriate Protocol Manual.

  • Page 15: Mechanical Installation

    WARNING! Follow the safety instructions given in this manual and the drive documentation. Mounting The FENA-01 is to be inserted into an available fieldbus adapter slot. The module is held in place with plastic pins and one screw. The screw also provides the electrical connection between the module and drive frame for cable shield termination.
  • Page 16 Mechanical installation...

  • Page 17: Electrical Installation

    Avoid parallel runs. Use bushings at cable entries. Ethernet connection The network cable is connected to the RJ45 connector (X1) on the FENA-01 module. Standard CAT5 UTP, FTP or STP cables can be used. When CAT5 FTP or STP is used, jumper J1 connects the cable shield internally either: •...
  • Page 18 Electrical installation...

  • Page 19: Definitions And Abbreviations

    FENA-01 Ethernet Adapter module The FENA-01 Ethernet Adapter module is one of the optional fieldbus adapter modules available for ABB drives. The FENA-01 is a device through which an ABB drive is connected to an Ethernet network. Parameter A parameter is an operating instruction for the drive. Parameters can be read and programmed using the drive control panel, or through the FENA-01 module.
  • Page 20 Definitions and abbreviations...

  • Page 21: Technical Data

    Technical data FENA-01 Enclosure: Mounting: Into the option slot on the drive. Degree of protection: IP20 Ambient conditions: The applicable ambient conditions specified for the drive in its manuals are in effect. Indicators: Three bicolor LEDs (HOST, MODULE, NETWORK) Connectors: •...

  • Page 22: Fieldbus Link

    Power supply: +3.3 V ±5% max. 400 mA (supplied by the drive) General: • Estimated min. lifetime: 100 000 h • All materials UL/CSA-approved • Complies with EMC standards EN 61000-6-4:2001and EN 61800-3 Fieldbus link Compatible Devices: Ethernet Standard IEEE 802.3 and IEEE 802.3u devices.
  • Page 24 ABB Oy ABB Inc. AC Drives Automation Technologies P.O. Box 184 Drives & Motors FI-00381 HELSINKI 16250 West Glendale Drive FINLAND New Berlin, WI 53151 Telephone +358 10 22 11 +358 10 22 22681 Telephone 262 785-3200 Internet http://www.abb.com 800-HELP-365...

Table of Contents